SGS Thomson Microelectronics LD1117VC, LD1117V50C, LD1117V50, LD1117V33, LD1117F12 Datasheet
...
1/24October 2003
■ LOW DROPOUT VOLTAGE (1V TYP.)
■ 2.85V DEVICE PERFORMANCES ARE
SUITABLE FOR SCSI-2 ACTIVE
TERMINATION
■ OUTPUT CURRENT UP TO 800 mA
■ FIXED OUTPUT VOLTAGE OF: 1.2V, 1.8V,
2.5V, 2 .85V, 3.0V, 3.3V, 5.0V
■ ADJUSTABLE VERSION AVAILABILITY
(V
rel
=1.25V)
■ INTERNAL CURRENT AND THERMAL LIMIT
■ AVAILABLEIN ± 1% (AT 25°C) AND 2% IN
FULL TEMPERATURE RANGE
■ SUPPLY VOLTAGE REJECTION: 75dB (TYP.)
DESCRIPTION
The LD1117 is a LOW DROP Voltage Regulator
able to provide up to 800m A of Output Current,
available even in adjustable version (V re f= 1.25V).
Concerning fixed v ers ions, are offered t he
following Output Voltages: 1.2V,1.8V,2.5V,2.85V,
3.0V 3.3V and 5.0V. The 2.85V type is ideal for
SCSI-2 lines active termination. The device is
supplied in: SOT-223, DPAK, SO-8, TO -220 and
TO-220FM. The SOT-223 and DPAK surface
mount packages optimize the thermal
characteristics even offering a relevant space
saving effect. High efficiency is assured by NPN
pass transistor. In fact in this case, unlike than
PNP one, the Quiescent Current flows mostly into
the load. Only a very commo n 10µF minim um
capacitor is ne eded for stability. On chip trimming
allows the regulator to reach a very tight out put
voltage tolerance, within ± 1% at 25°C. The
ADJUSTABLE LD1117 is pin to pin compatible
with the other standard. Adjustable voltage
regulators maintainin g the better performances in
terms of D rop and Tolerance.
LD1117
SERIES
LOW DROP F IXED AND ADJUSTABLE
POSITIVE VOLTAGE REGULATORS
BLOCK DIAGRAM
SOT-223DPAK
TO-220FM
SO-8
TO-220
LD1117 SERIES
2/24
ABSOLUTE MAXIMUM RAT INGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is
not implied. Over the above suggested Max Power Dissipation a Short Circuit could definitively damage the device.
THERMAL DATA
APPLICATION CIRCUIT (FOR 1.2 V)
APPLICATION CIRCUIT (FOR OTHER FIXED OUTPUT VOLTAGES)
Symbol Parameter² Value Unit
V
IN
DC Input Voltage
15 V
P
tot
Power Dissipation
12 W
T
stg
Storage Temperature Range
-40 to +150 °C
T
op
Operating Junction Temperature Range for C Version -40 to +125 °C
for standard Version 0 to +125 °C
Symbol Parameter SOT-223 SO-8 DPAK TO-220 TO-220FM Unit
R
thj-case
Thermal Resistance Junction-case
15 20 8 3 4 °C/W
R
thj-amb
Thermal Resistance Junction-ambient
50 60 °C/W
LD1117 SERIES
3/24
CONNECTION DIAGRAM (top v iew)
NOTE: The TAB is connected to the V
OUT
.
ORDERING CODES
SOT-223 SO-8 DPAK TO-220 TO-220FM
OUTPUT
VOLTAGE
LD1117S12 LD1117D12 (*) LD1117DT12 LD1117V12 (*) LD1117F12 (*) 1.2 V
LD1117S18 LD1117D18 LD1117DT18 LD1117V18 LD1117F18 1.8 V
LD1117S18C LD1117D18C LD1117DT18C LD1117V18C LD1117F18C 1.8 V
LD1117S25 LD1117D25 LD1117DT25 LD1117V25 LD1117F25 2.5 V
LD1117S25C LD1117D25C LD1117DT25C LD1117V25C LD1117F25C 2.5 V
LD1117S28 LD1117D28 LD1117DT28 LD1117V28 LD1117F28 2.85 V
LD1117S30 LD1117D30 LD1117DT30 LD1117V30 LD1117F30 3 V
LD1117S30C LD1117D30C LD1117DT30C LD1117V30C LD1117F30C 3 V
LD1117S33 LD1117D33 LD1117DT33 LD1117V33 LD1117F33 3.3 V
LD1117S33C LD1117D33C LD1117DT33C LD1117V33C LD1117F33C 3.3 V
LD1117S50 LD1117D50 LD1117DT50 LD1117V50 LD1117F50 5 V
LD1117S50C LD1117D50C LD1117DT50C LD1117V50C LD1117F50C 5 V
LD1117S LD1117D LD1117DT LD1117V LD1117F ADJUSTABLE
FROM 1.25 TO
15V
LD1117SC LD1117DC LD1117DTC LD1117VC LD1117FC ADJUSTABLE
FROM 1.25 TO
15V
SOT-223 SO-8
TO-220FM
DPAK
TO-220
LD1117 SERIES
4/24
(*) Available on request
ELECTRICAL CHARACTERISTICS OF LD1117#12 (refer to the test circuits, TJ= 0 to 125° C,
C
O
= 10 µF, R = 120 Ω b etwe en GND and OUT pi ns , unless otherwise specified)
ELECTRICAL CHARACTERISTICS OF LD1117#18 (refer to the test circuits, T
J
= 0 to 125° C,
C
O
= 10 µF unless otherwise specified)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
ref
Reference Voltage IO=10to800mA Vin-VO= 1.4 to 10 V 1.140 1.20 1.260 V
∆V
O
Line Regulation Vin-VO= 1.5 to 13.75 V IO= 10 mA 0.035 0.2 %
∆V
O
Load Regulation Vin-VO=3V IO= 10 to 800 mA 0.1 0.4 %
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage 15 V
I
adj
Adjustment Pin Current Vin≤ 15 V 60 120 µA
∆I
adj
Adjustment Pin Current
Change
Vin-VO= 1.4 to 10 V
I
O
=10to800mA
15µA
I
O(min)
Minimum Load Current Vin=15V 2 5 mA
I
O
Output Current Vin-VO=5V TJ= 25°C 800 950 1300 mA
eN Output Noise (%V
O
) B =10Hz to 10KHz TJ= 25°C 0.003 %
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in-VO
=3V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA 1 1.1 V
I
O
= 500 mA 1.05 1.15
I
O
= 800 mA 1.10 1.2
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
O
Output Voltage Vin= 3.8 V IO=10mA TJ= 25°C 1.78 1.8 1.82 V
V
O
Output Voltage IO= 0 to 800 mA Vin= 3.3 to 8 V 1.76 1.84 V
∆V
O
Line Regulation Vin= 3.3 to 8 V IO= 0 mA 1 6 mV
∆V
O
Load Regulation Vin= 3.3 V IO= 0 to 800 mA 1 10 mV
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage IO= 100 mA 10 V
I
d
Quiescent Current Vin≤ 8V 5 10 mA
I
O
Output Current Vin= 6.8 V TJ= 25°C 800 950 1300 mA
eN Output Noise Voltage B =10Hz to 10KHz T
J
= 25°C 100 µV
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in
= 5.5 V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA 1 1.1 V
I
O
= 500 mA 1.05 1.15
I
O
= 800 mA 1.10 1.2
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
LD1117 SERIES
5/24
ELECTRICAL CHARACTERISTICS OF LD1117#25 (refer to the test circuits, TJ= 0 to 125° C,
C
O
= 10 µF unless otherwise specified)
ELECTRICAL CHARACTERISTICS OF LD1117#28 (refer to the test circuits, T
J
= 0 to 125° C,
C
O
= 10 µF unless otherwise specified)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
O
Output Voltage Vin= 4.5 V IO=10mA TJ= 25°C 2.475 2.5 2.525 V
V
O
Output Voltage IO= 0 to 800 mA Vin= 3.9 to 10 V 2.45 2.55 V
∆V
O
Line Regulation Vin= 3.9 to 10 V IO= 0 mA 1 6 mV
∆V
O
Load Regulation Vin= 3.9 V IO= 0 to 800 mA 1 10 mV
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage IO= 100 mA 15 V
I
d
Quiescent Current Vin≤ 10 V 5 10 mA
I
O
Output Current Vin= 7.5 V TJ= 25°C 800 950 1300 mA
eN Output Noise Voltage B =10Hz to 10KHz T
J
= 25°C 100 µV
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in
= 5.5 V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA 1 1.1 V
I
O
= 500 mA 1.05 1.15
I
O
= 800 mA 1.10 1.2
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
O
Output Voltage Vin= 4.85 V IO=10mA TJ= 25°C 2.82 2.85 2.88 V
V
O
Output Voltage IO= 0 to 800 mA Vin= 4.25 to 10 V 2.79 2.91 V
∆V
O
Line Regulation Vin= 4.25 to 10 V IO= 0 mA 1 6 mV
∆V
O
Load Regulation Vin= 4.25 V IO= 0 to 800 mA 1 10 mV
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage IO= 100 mA 15 V
I
d
Quiescent Current Vin≤ 10 V 5 10 mA
I
O
Output Current Vin= 7.85 V TJ= 25°C 800 950 1300 mA
eN Output Noise Voltage B =10Hz to 10KHz T
J
= 25°C 100 µV
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in
= 5.85 V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA 1 1.1 V
I
O
= 500 mA 1.05 1.15
I
O
= 800 mA 1.10 1.2
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
LD1117 SERIES
6/24
ELECTRICAL CHARACTERISTICS OF LD1117#30 (refer to the test circuits, TJ= 0 to 125° C,
C
O
= 10 µF unless otherwise specified)
ELECTRICAL CHARACTERISTICS OF LD1117#33 (refer to the test circuits, T
J
= 0 to 125° C,
C
O
= 10 µF unless otherwise specified)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
O
Output Voltage Vin=5V IO=10mA TJ= 25°C 2.97 3 3.03 V
V
O
Output Voltage IO= 0 to 800 mA Vin= 4.5 to 10 V 2.94 3.06 V
∆V
O
Line Regulation Vin= 4.5 to 12 V IO= 0 mA 1 6 mV
∆V
O
Load Regulation Vin= 4.5 V IO= 0 to 800 mA 1 10 mV
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage IO= 100 mA 15 V
I
d
Quiescent Current Vin≤ 12 V 5 10 mA
I
O
Output Current Vin=8V TJ= 25°C 800 950 1300 mA
eN Output Noise Voltage B =10Hz to 10KHz T
J
= 25°C 100 µV
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in
=6V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA 1 1.1 V
I
O
= 500 mA 1.05 1.15
I
O
= 800 mA 1.10 1.2
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
O
Output Voltage Vin= 5.3 V IO=10mA TJ= 25°C 3.267 3.3 3.333 V
V
O
Output Voltage IO= 0 to 800 mA Vin= 4.75 to 10 V 3.235 3.365 V
∆V
O
Line Regulation Vin= 4.75 to 15 V IO= 0 mA 1 6 mV
∆V
O
Load Regulation Vin= 4.75 V IO= 0 to 800 mA 1 10 mV
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage IO= 100 mA 15 V
I
d
Quiescent Current Vin≤ 15 V 5 10 mA
I
O
Output Current Vin= 8.3 V TJ= 25°C 800 950 1300 mA
eN Output Noise Voltage B =10Hz to 10KHz T
J
= 25°C 100 µV
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in
= 6.3 V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA 1 1.1 V
I
O
= 500 mA 1.05 1.15
I
O
= 800 mA 1.10 1.2
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
LD1117 SERIES
7/24
ELECTRICAL CHARACTERISTICS OF LD1117#50 (refer to the test circuits, TJ= 0 to 125° C,
C
O
= 10 µF unless otherwise specified)
ELECTRICAL CHARACTERISTICS OF LD1117 (ADJ USTABLE) (refer to the tes t circuits,
T
J
= 0 to 125° C, CO= 10 µF unless otherwise specified)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
O
Output Voltage Vin=7V IO=10mA TJ= 25°C 4.95 5 5.05 V
V
O
Output Voltage IO= 0 to 800 mA Vin= 6.5 to 15 V 4.9 5.1 V
∆V
O
Line Regulation Vin= 6.5 to 15 V IO= 0 mA 1 10 mV
∆V
O
Load Regulation Vin= 6.5 V IO= 0 to 800 mA 1 15 mV
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage IO= 100 mA 15 V
I
d
Quiescent Current Vin≤ 15 V 5 10 mA
I
O
Output Current Vin=10V TJ= 25°C 800 950 1300 mA
eN Output Noise Voltage B =10Hz to 10KHz T
J
= 25°C 100 µV
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in
=8V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA 1 1.1 V
I
O
= 500 mA 1.05 1.15
I
O
= 800 mA 1.10 1.2
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
ref
Reference Voltage Vin-VO=2V IO=10mA TJ= 25°C 1.238 1.25 1.262 V
V
ref
Reference Voltage IO=10to800mA Vin-VO= 1.4 to 10 V 1.225 1.275 V
∆V
O
Line Regulation Vin-VO= 1.5 to 13.75 V IO= 10 mA 0.035 0.2 %
∆V
O
Load Regulation Vin-VO=3V IO= 10 to 800 mA 0.1 0.4 %
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage 15 V
I
adj
Adjustment Pin Current Vin≤ 15 V 60 120 µA
∆I
adj
Adjustment Pin Current
Change
Vin-VO= 1.4 to 10 V
I
O
=10to800mA
15µA
I
O(min)
Minimum Load Current Vin=15V 2 5 mA
I
O
Output Current Vin-VO=5V TJ= 25°C 800 950 1300 mA
eN Output Noise (%V
O
) B =10Hz to 10KHz TJ= 25°C 0.003 %
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in-VO
=3V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA 1 1.1 V
I
O
= 500 mA 1.05 1.15
I
O
= 800 mA 1.10 1.2
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
LD1117 SERIES
8/24
ELECTRICAL CHARACTERISTICS OF LD1117#18C (refer to the test circuits, TJ= -40 to 125°C,
C
O
= 10 µF unless otherwise specified)
ELECTRICAL CHARACTERISTICS OF LD1117#25C (refer to the test circuits, T
J
= -40 to 125°C,
C
O
= 10 µF unless otherwise specified)
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
O
Output Voltage Vin= 3.8 V IO=10mA TJ= 25°C 1.76 1.8 1.84 V
V
O
Output Voltage IO= 0 to 800 mA Vin= 3.9 to 10 V 1.73 1.87 V
∆V
O
Line Regulation Vin= 3.3 to 8 V IO= 0 mA 1 30 mV
∆V
O
Load Regulation Vin= 3.3 V IO= 0 to 800 mA 1 30 mV
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage IO= 100 mA 10 V
I
d
Quiescent Current Vin≤ 8V 5 10 mA
I
O
Output Current Vin= 6.8 V TJ= 25°C 800 950 1300 mA
eN Output Noise Voltage B =10Hz to 10KHz T
J
= 25°C 100 µV
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in
= 5.5 V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA TJ= 0 to 125°C 1 1.1 V
I
O
= 500 mA TJ= 0 to 125°C 1.05 1.15
I
O
= 800 mA TJ= 0 to 125°C 1.10 1.2
V
d
Dropout Voltage IO= 100 mA 1.1 V
I
O
= 500 mA 1.2
I
O
= 800 mA 1.3
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
Symbol Parameter Test Conditions Min. Typ. Max. Unit
V
O
Output Voltage Vin= 4.5 V IO=10mA TJ= 25°C 2.45 2.5 2.55 V
V
O
Output Voltage IO= 0 to 800 mA Vin= 3.9 to 10 V 2.4 2.6 V
∆V
O
Line Regulation Vin= 3.9 to 10 V IO= 0 mA 1 30 mV
∆V
O
Load Regulation Vin= 3.9 V IO= 0 to 800 mA 1 30 mV
∆V
O
Temperature Stability 0.5 %
∆V
O
Long Term Stability 1000 hrs, TJ= 125°C 0.3 %
V
in
Operating Input Voltage IO= 100 mA 15 V
I
d
Quiescent Current Vin≤ 10 V 5 10 mA
I
O
Output Current Vin= 7.5 V TJ= 25°C 800 950 1300 mA
eN Output Noise Voltage B =10Hz to 10KHz T
J
= 25°C 100 µV
SVR Supply Voltage Rejection I
O
= 40 mA f = 120Hz TJ= 25°C
V
in
= 5.5 V V
ripple
=1V
PP
60 75 dB
V
d
Dropout Voltage IO= 100 mA TJ= 0 to 125°C 1 1.1 V
I
O
= 500 mA TJ= 0 to 125°C 1.05 1.15
I
O
= 800 mA TJ= 0 to 125°C 1.10 1.2
V
d
Dropout Voltage IO= 100 mA 1.1 V
I
O
= 500 mA 1.2
I
O
= 800 mA 1.3
Thermal Regulation T
a
= 25°C 30ms Pulse 0.01 0.1 %/W
Loading...