SGS 26CC Owner's Manual
FOR YOUR SAFETY
PLEASE READ THESE INSTRUCTIONS CAREFULLY
AND RETAIN THEM FOR FUTURE USE.
OWNER’S MANUAL
26CC PETROL STRIMMER
PAGE 2
PAGE 3
1. FOR SAFE OPERATION
Read operator’s instruction book before
operating this machine.
Read, understand and follow all warnings.
Wear head, eye and ear protection.
Use suitable work-wear to protect yourself.
Watch out for thrown objects & ricochets
The operator of the machine must ensure,
while working, that no persons or animals
come closer than 50 feet (15 meters).
Only use non--metallic, flexible
cutting attachments, i.e. trimmer
heads with trimmer line.
1. For Safe Operation 3 - 15
2. Components Diagram 16
3. Assembly 17 - 20
4. Filling with Fuel and Oil 21 - 24
5. Starting / Stopping 25 - 27
6. Operating Advice 28 - 29
7. Maintenance 30 - 34
8. Transporting 35
9. Troubleshooting 36
10. Technical Specification 37
11. Confirmation of Conformity 38
CONTENTS
WWW.SGS-ENGINEERING.COM
CALL FOR ASSISTANCE: 01332 576 850
PAGE 5
PAGE 4
1. FOR SAFE OPERATION
GLOVES
Gloves should be worn when necessary, e.g.,
when fitting cutting attachments.
HEARING PROTECTION
Wear hearing protection that provides adequate noise reduction.
EYE PROTECTION
Always wear approved eye protection. If you
use a visor then you must also wear approved
protective goggles. Approved protective goggles must comply with your countries relevent
safety standard.
BOOTS
Wear sturdy, non--slip boots.
CLOTHING
Wear clothes made of a strong fabric and
avoid loose clothing that can catch on twigs
and branches. Always wear heavy, long pants.
Do not wear jewellery, shorts sandals or go
barefoot. Secure hair so it is above shoulder
level.
1. FOR SAFE OPERATION
This section describes the machine’s safety equipment, its
purpose, and how checks and maintenance should be carried out to ensure that it operates correctly.
The life span of the machine can be reduced and the risk of
accidents can increase if machine maintenance is not carried
out correctly and if service and/or repairs are not carried out
professionally. If you need further information please contact
us at SGS Engineering.
Stop switch
Make sure the engine stops when you push and hold the
stop switch.
Never use a machine that has faulty safety
equipment! Carry out the inspection, maintenance and service routines listed in this section. If your machine fails any of these checks,
contact your service agent to get it repaired.
WWW.SGS-ENGINEERING.COM
CALL FOR ASSISTANCE: 01332 576 850
PAGE 7
PAGE 6
1. FOR SAFE OPERATION
WARNING: Never use a cutting attachment
without an approved guard.
Use of incorrectly wound trimmer line or an incorrect cutting
attachment increases the level of vibration.
WARNING: Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience
symptoms of overexposure to vibration. Such symptoms
include numbness, loss of feeling, tingling, pricking, pain,
loss of strength, changes in skin colour or condition.
1. FOR SAFE OPERATION
Muffler
The muffler is designed to reduce the noise
level and to direct the exhaust gases away
from the operator.
CAUTION! Muffler is fitted with a catalytic
converter designed to reduce exhaust gas
emissions.
For mufflers, it is very important that you follow the instructions on checking, maintaining, and servicing your machine.
See Checking, maintaining and servicing the machine’s
safety equipment section.
CAUTION: Mufflers fitted with catalytic
converters get very hot during use and remain
so for some time after stopping. This also
applies at idle speed. Contact can result in
burns to the skin.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to the
machine. The muffler on this unit is equipped with a special
spark arrestor mesh. The mesh should be checked and, if
necessary, cleaned by a servicing dealer. A blocked mesh will
cause the machine to overheat, which can lead to serious
damage.
WWW.SGS-ENGINEERING.COM
CALL FOR ASSISTANCE: 01332 576 850
Cutting attachment guard
This guard is intended to prevent
loose objects from being thrown
towards the operator. The guard also
protects the operator from accidental
contact with the cutting attachment.
Ensure that the guard is undamaged
and is not cracked. Replace the guard
if it has been exposed to impact or is
cracked.
PAGE 9
PAGE 8
1. FOR SAFE OPERATION
1. FOR SAFE OPERATION
This section describes how to choose and maintain your cutting equipment in order to:
• Obtain maximum cutting performance.
• Extend the life of the cutting equipment.
General rules
1. Only use cutting attachments with the guards recommended by SGS Engineering.
2. Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be replaced.
Never use a machine with faulty safety equipment. The machine’s safety equipment must be
checked and maintained as described in this
section.
Trimmer head
• Only use SGS Engineering recommended cutting
attachments.
• Smaller machines generally require small trimmer heads
and vice versa. This is because when clearing using trimmer line, the engine must throw out the trimmer line
radially from the trimmer head, and overcome the resistance of the grass being cleared.
• The length of the trimmer line is also important. A longer
trimmer line requires greater engine power than a
shorter trimmer line of the same diameter.
• Make sure that the cutter on the trimmer guard is intact.
This is used to cut the trimmer line to the correct length.
• To increase the life of the trimmer line it can be soaked in
water for a couple of days. This will make the line tougher and last longer.
WWW.SGS-ENGINEERING.COM
CALL FOR ASSISTANCE: 01332 576 850
PAGE 11
PAGE 10
1. FOR SAFE OPERATION 1. FOR SAFE OPERATION
The only accessories you can operate with this
engine unit are the cutting attachments we recommend. Never use wire, rope, string, etc.
Never use the machine if you are tired, if you have
drunk alcohol, or if you are taking medication that
could affect your vision, your judgment or your
coordination.
Never use the machine in extreme weather conditions such as severe cold, very hot and/or humid
climates.
Never use a machine that has been modified in any
way from its original specification.
Wear personal protective equipment.
Never use a machine that is faulty. Carry out the
checks, maintenance and service instructions
described in this manual. Some maintenance and
service measures must be carried out by trained
and qualified specialists.
All covers and guards must be fitted before starting.
Make sure the spark plug cap and lead are not damaged. Otherwise you could get an electric shock.
All covers and guards must be fitted before starting.
Make sure the spark plug cap and lead are not damaged. Otherwise you could get an electric shock.
The machine operator must ensure that no people
or animals come closer than 50 feet (15 meters)
while working.
Stay clear of spinning line.
Secure or remove loose clothing or clothing with
loosely hanging ties, straps, tassels, etc. They can
be caught in moving parts.
Being fully covered also helps protect you from
debris and pieces of toxic plants thrown by spinning
line.
Keep handles free of oil and fuel.
Always keep the engine on the right hand side of
your body.
Hold the unit firmly with both hands.
Keep trimmer head below waist level.
The machine is only designed for trimming grass.
WWW.SGS-ENGINEERING.COM
CALL FOR ASSISTANCE: 01332 576 850
Loading...