SEVIC SV070270D, VISION LIBERTY COMBO 2 Operating Manual

Download

- 1 -

SV070270D

- Operating manual

VISION LIBERTY COMBO 2

- 2 -

Introduction

Thank you for choosing the 7” portable DVD player. The unit applies the latest state of the art electronics and is designed for use in hotels, offices or your home. The DVD Player is constructed to provide years of reliable, trouble-free service, and is compact so that you can take it with you anywhere and is designed for quick and easy setup. Please read all documentation prior to using this product. The documentation will assist you in obtaining the best equipment performance. Save this manual for later use.

Important Notice

It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver’s seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. In the interest of safety, this system should never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle.

Safety Precaution

For safety reasons, when changing video media, it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system. Enjoy your entertainment system but always remember-safety of all passengers remains the number one priority.

- -3

Important Safety Instruction

This product has been listed as class 1 laser product. The mark is on the rear panel.

CAUTION

1. The product contains a low-power laser device. In order to ensure the safety of the laser device, do not remove any cover and attempt to repair the unit. If any service is needed, please contact the distributor or its authorized service center.

2. To reduce the risk of electric shock, do not remove the cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. Unplug the product from the wall outlet before servicing or when it is unused for a long period of time.

3. The manufacturer should not hold responsibility for the damage caused by any

substitutions and modifications of the product without authorization from the manufacturer or authorized unit.

4. Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type.

WARNING

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CLASS 1 LASER PRODUCTCLASS 1 LASER PRODUCT

- 4 -

Important Safety Instruction

Notes

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Maintain well ventilated conditions around

the product. Do not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9. Read, heed and follow all instructions to ensure correct and safe installation and

interconnection of the apparatus;

10. The apparatus shall not be exposed to dripping or splashing and that no objects

filled with liquids, such as vases, shall be placed on the apparatus;

11. The mains plug shall remain readily operable;

12. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13. Only use attachments/accessories specified by the manufacturer.

14. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

15. Unplug the apparatus during lightning storms or when unused for long periods of

time.

16. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

- -5

Table Of Contents

Introduction-------------------------------------------------------------------------------------------Important Safety Instruction--------------------------------------------------------------------Table of Contents ----------------------------------------------------------------------------------Main Features ---------------------------------------------------------------------------------------View of Main Unit-----------------------------------------------------------------------------------Remote Control -------------------------------------------------------------------------------------System Connections ------------------------------------------------------------------------------

Connecting to AC Adapter -------------------------------------------------------------------------Connecting to a TV-----------------------------------------------------------------------------------Connecting to a NormalAmplifier ---------------------------------------------------------------Connecting to a Digital Amplifier -----------------------------------------------------------------Connecting to External AV Signal Source------------------------------------------------------Connecting to DC Adapter-------------------------------------------------------------------------Playback Preparations ---------------------------------------------------------------------------Using Of Remote Control --------------------------------------------------------------------------Using Wired Headphone ---------------------------------------------------------------------------Using Wireless Headphone -----------------------------------------------------------------------Disc Formats Supported By This Player -------------------------------------------------------Rechargeable Battery Pack---------------------------------------------------------------------About Rechargeable Battery Pack---------------------------------------------------------------Battery Pack Attaching and Placement---------------------------------------------------------Charging the Battery Pack ------------------------------------------------------------------------Detaching the Battery Pack -----------------------------------------------------------------------Playback Operation -------------------------------------------------------------------------------DVD Playback-----------------------------------------------------------------------------------------CD Playback-------------------------------------------------------------------------------------------JPEG Playback---------------------------------------------------------------------------------------DIVX Playback-----------------------------------------------------------------------------------------

System Setup ---------------------------------------------------------------------------------------Troubleshooting ------------------------------------------------------------------------------------Specifications-----------------------------------------------------------------------------------------

1 2 4 5 6 8 10 10 10 11 11 12 12 12 13 13 14 15 16 16 17 18 19 20 21 23 24 24 26 29 30

- 6 -

Main Features

High Quality Audio and Video

Excellent Sound

Dolby Digital output to produce excellent audio output signal.

High Resolution

MPEG2 decoding format achieves more than 500 lines of horizontal resolution.

LCD (Liquid Crystal Display) Screen

Designed with a 7” color LCD screen.

Special Functions

Supports parental-lock features.

AV Input

External audio, video input can be connected to most external AV sources.

Digital Out

Convenient optical digital audio output jack for connecting with most amplifiers.

Headphone Output

Movie or music audio in private.

Switching Power Adapter

Automatically adapts to voltage required.

Advanced Playing Function

Compatibility

DVD, CD, CD-R, CD-RW and JPEG discs are compatible.

ON-Screen Display

ON-screen displays in your choice of English /Spanish/ French /Italy/German.

Viewing Performance

Multi-speed, fast forward, fast backward, slow play and repeat playback.

Zoom Function

Allows the viewer to zoom in the picture.

Search By Time

Search for a certain time on a disc.

Last Memory Playback

Continues playing from a stopped point as long as power is applied to the DVD Player.

Region Code

DVD players and discs are coded by region. These regional codes must match the played discs. If the codes don’t match, the disc cannot be played. This player’s default code is region 2.

- 7 -

View of Main Unit

Front and Right Panel

1. PIC button

Press to enter the brightness, color or contrast adjusting mode, then use the +/button to adjust the items. Press and hold the button for about 1~2 seconds to shift screen aspect ration between 16:9 and 4:3.

2. /-button

Press to go to beginning of a previous track/chapter. Press to decrease the brightness, color or contrast level in the adjusting mode.

3. +/ button

Press to go to next track/chapter. Press to increase the brightness, color or contrast level in the adjusting mode.

4. / PLAY/PAUSE button

Press to start playback or pause playback.

5. / STOP/ EJECT button

Press to stop playback. Press again to go to the beginning of the movie. Press to eject the disc.

6. ON/OFF button

Press and hold for 1.5 seconds to turn Power On or OFF.

7. Infrared (IR) Audio Signal Emitter/ (IR) Remote Sensor

IR Transmitter for optical wireless IR headphones. IR Sensor for remote control operation.

- 8 -

View of Main Unit

8. Power ON Indicator

Light turns green when the player is in work status. It will turn off automatically when enter standby mode.

9. Speakers

Provides high quality Audio outputs.

10. Disc Tray

When loading the disc into the disc tray, it will be automatically slotted in.

11. LCD Screen

Provides a high-resolution picture.

Left Panel

1. Headphone Jack

Used to connect to wired headphone for private listening. When headphone is connected, the speakers will automatically turn off.

2. Speaker/Headphone Volume Adjusting control

Used to adjust the headphone and speaker volume.

3. Video Input/Output Jack

Used for connection to an external monitor or video source.

4. Audio Input/Output and Optical Digital Output Jack

Used for connection to an external amplifier or digital processor or external audio source.

5. AV IN/OUT Switch

Switch to IN to input an external audio/video source. Switch to OUT when the player is connected to an external monitor.

6. DC 12V Input Jack

For connecting to power supply, including Car Adapter.

- 9 -

Remote Control

1. PWR button

Press to turn ON or OFF the power.

2. SUBT button

When a DVD with subtitles is playing, press to select a subtitle language or to turn subtitle OFF.

3. TITLE button

Press to display titles if present on the disc.

4. Direction buttons

Press to select menu items.

5. ENTER button

Press to confirm the items or settings.

6. SETUP button

Press to access the DVD player’s setup menu.

7. 0-9 Number buttons

Select 0-9 numbers by pressing these buttons.

8.  PREV SKIP button

Press to go to beginning of the previous track/chapter.

- 10 -

Remote Control

9.  NEXT SKIP button

Press to go to next track /chapter.

10. A-B Repeat button

Used to play a section of the DVD from point A to point B. Press once to select the starting point (A) press again to select the end point (B). Press a third time to stop the A-B Repeat

11. REP button

Press to repeat a chapter, track, title, or the entire disc.

12. EJECT button

Press to eject disc.

13. AUDIO button

Press to access various audio languages, when the DVD disc contains multiple audio languages.

14. BACK LIGHT button

Press to turn the screen on or off.

15. MENU button

Press to open the disc menu.

16. INFO button

Press for detailed information on the disc. Keep pressing the button to

remove information from screen.

17. STOP button

Press once to stop playback. Press the PLAY/PAUSE button to resume normal playback. Press the button twice to stop playback completely.

18. /PLAY/PAUSE button

Press to start playback. Press again to pause playback.

19. GOTO button

Press to select the desired disc starting time, track or title.

20. +10 button

Select numbers greater than 9 by pressing the (+10) button first, and then additional number buttons as needed.

21.  FWD SCAN button

Press to search forward.

22.  REV SCAN button

Press to search backward.

23. SLOW button

Press to activate slow playback.

24. ZOOM button

Press to enter and cycle through zoom functions, use the direction buttons to move around the screen.

- 11 -

System Connections

 Always ensure that the DVD player, TV and any other electrical equipment to be

connected to the DVD player are switched OFF.

 Ensure that you observe the color coding when connecting audio and video

cables.

Connecting to AC Adapter

Connect the supplied adapter to the side of the DVD player in the jack marked “DC 12V IN”. Plug the two-prong end of the power cord to an AC100-240V outlet. If you have difficulty inserting the plug, turn it over and reinsert it. If the DVD Player will not be used for a long time, disconnect the plug from the outlet.

Connecting To a TV

Audio/video connections

The easiest way to connect the DVD player to a television is via the supplied Audio/Video cable. Connect the audio/video cable from the DVD player to the

audio/video inputs of the TV. And also switch the AV IN/OUT to OUT.

- 12 -

System Connections

Connecting to a Normal Amplifier

The DVD player can be connected to an amplifier. Please refer to the equipment’s manual before connecting. After connecting, switch the AV IN/OUT to OUT.

Connecting to a Digital Amplifier

The DVD Player can be connected to an amplifier with a digital optical input. The cable is not supplied, but can be purchased at most home electronics retailer. Refer to the operation manual of the digital amplifier when connecting. After connecting, switch the AV IN/OUT to OUT.

- 13 -

System Connections

Connecting to External AV Signal Source

The unit supports AV signal input function. Use the audio/video cable to connect the unit to the external AV signal source such as a DVD, VCR etc. after connecting, switch theAV IN/OUT button toAV IN.

Connecting to DC Adapter

To use the Vehicle DC Adapter disconnect the Battery pack and connect the supplied Vehicle Power Plug Adapter into the DVD Player’s Power Jack and the other end into the Vehicle DC outlet (Cigarette Lighter Socket) as shown below.

 Do not operate the unit or view video software while driving a vehicle.  Place the unit in a secure position for viewing.  Do not leave battery attached when using car adaptor as power source.  Make sure the unit and the car adapter are not connected when starting the car.

- 14 -

Playback Preparations

Using of Remote Control

1. Remove the empty battery receptacle. Refer to the drawing above.

2. Insert the battery into the receptacle and insert the receptacle into the remote.

3. For best results, aim the remote directly at the player’s receiving window within

15 feet, and angles of not exceeding 60 degrees.

4. The path between the remote control and remote sensor should be free of

obstructions.

5. Under normal use the battery will last for one year.

6. Remove battery if the remote is not to be used for a long time or during storage.

- 15 -

Playback Preparations

Using wired Headphone

Connect headphone into the headphone Jack onthe left side of the unit. As shown below:

Quick Tips:

 Excessively loud volume could

damage your hearing.

 Turn down the volume before you

connect the headphones, and then raise the volume to comfortable level.

 Sound from the DVD Player’s

external speaker will stop when headphones are connected.

Using Wireless Headphone

The unit also supports IR function. You can use a wireless headphone when

listening the music. Please take the steps below when using the wireless headphone.

1. For best results, when using wireless headphone sit facing the screen, within the range of 12 feet and angles of 60 degrees, and without obstacles between wireless headphones and infrared audiosignal emitter.

2. Set the IR ON in the audio setup menu first.

3. If there is no sound, make sure the batteries in the headphones are not discharged.

- 16 -

Playback Preparations

Disc Formats Supported By This Player

DISC LOGO DIAMETER

PLAYBACK TIME/ PLAYABLE SIDES

133 mi n ( SS-SL) 242 min (SS-DL )

266 min (DS-SL)

DVD 12cm

484 min ( DS-DL)

CD 12cm 74 min

JPEG 12cm

DIVX 12cm

The disc maker specifies the operation of some DVD discs. Please refer to the instruction manual with the disc.

Care of Discs

Do not touch the playing surface of the compact disc.

Do not stick paper labels on the disc.

Storage of Discs

Do not expose discs to direct sunlight or excessive temperatures

Cleaning of Discs

If a disc has fingerprints or dust on it, lightly wipe the disc with soft cloth from

the center of the disc outward in a circular manner.

Never use record cleaning sprays, or any other solvents to clean your discs.

- 17 -

Rechargeable Battery Pack

About Rechargeable Battery Pack

Your portable DVD player comes with a lithium ion rechargeable battery that attaches to the bottom of the player. Your new battery should be fully charged before initial use. Charging time is normally about 5 hours. A fully charged battery delivers about 2.5 hours of use, but playing time varies from disc to disc. If the battery will not be used for a long period of time, first fully charge the battery prior to storage.

Working conditions and precautions of the battery

 New batteries should be fully charged before initial use.  Battery should only be used and charged when temperatures are between

32-100F.

 Never put the battery in fire or water.  Do not expose the battery to high temperatures or store in hot, sunny

places.

 Maintain well-ventilated conditions around the product, avoiding heat. Don’t

put the product on bed, sofa or anything that may block ventilation to the product.

 Do not open the battery.  Never charge the battery for more than 8 hours. Detach battery immediately

after charging is complete if not being used. When charging the battery pack, the light on the battery will turn red, when the charging is complete or the battery is being used, the light will turn green.

 Detach battery when not in use.  When the battery is weak, a mark which indicates the battery is weak will

appear on the LCD screen, and about one minute later, the player will turn powerOFF automatically.

Notes: in the case of using adapter, the LCD screen will be lighter than with the rechargeable battery.

- 18 -

Rechargeable Battery Pack

Warning:

Do not touch any metal objects to the battery connectors, as it will put the battery in standby mode. To exit the standby mode, connect the battery and DVD player to AC or DC power.

Battery Pack Attaching and Placement

The DVD Player’s power supply is the AC power adapter or the battery pack, which are provided with the player. The battery pack also can be used as a stand. Refer to the following steps for attaching the Battery Pack:

1. Place the DVD Player on a soft and smooth surface with its back cover facing UP to avoid scratching the screen.

2. Position the Battery Pack directly toward the battery slot on the back cover of the DVD Player.

3. Align the pins on the battery pack with holes on the player.

With one hand on the DVD Player to prevent it from moving, and push the battery pack into the DVD Player. Then slide the Battery Pack toward the back of the DVD Player until you hear it click and lock into place.

- 19 -

Rechargeable Battery Pack

After attaching the Battery Pack, place the DVD Player LCD screen in normal position. The attached Battery Pack serves as a stand. The battery pack can be locked with the main unit. As shown below:

When used in a vehicle, the DVD Player is placed into a sturdy carrying Bag/Mount. The Bag/Mount is easy to attach to a headrest and fits on most vehicle headrest

types. This is convenient for the rear seat passengers to view the screen.

Charging the Battery Pack

The battery must be attached to the DVD player to charge it. Plug the Power Adapter into the Player’s DC 12V IN Jack, which is located on left Side of the DVD Player. Plug the other end of the Power Cord into a wall Outlet.

- 20 -

Rechargeable Battery Pack

Detaching the Battery Pack

If the DVD Player is not going to be used for long periods of time, the Battery Pack should be detached. When the DVD Player is turned OFF, the DVD Player is still consuming some power in STANDBY mode. This could lead to discharging the battery.

1. Place the player on a soft and smooth surface with its back cover up to avoid scratching the screen.

2. Press the button located on the backside of the unit to unlock the battery pack and while pressing the button pullthe battery pack out from the DVD Player.

Note: Please detach the battery pack when Car Adapter is connected with the unit. When attaching or detaching the battery pack, make sure to protect the

LCD screen.

- 21 -

Playback Operation

Pre-Operation

1. Connect the DVD Player to power supply.

2. Press the “POWER” switch to turn on the power of the unit.

3. Hand the disc with its printed side toward you (Refer to the picture below). Push

the disc in about ¾of the way. The disc will be imbibed into the player from the

rest of the way automatically.

4. Adjust the volume with the “VOLUME” adjust knob (also adjust headphone volume if using headphones).

Read all instructions carefully before using your DVD Player for the first time.

WARNING: Do not play poor-quality discs to avoid damaging the lens.

General operation of some buttons

Play/Pause

Press the /Play/Pause button once to pause playback. Press the /Play/Pause button again to resume normal playback.

Stop

During playback, press the STOP or / button once to stop playback of a disc. Press the/ button and the DVD Player will resume playback of the disc from the point where it stopped.

A-B

During normal playback, press the A-B button to select the segment that you want to play repeatedly. Press once to select the beginning point “A”, press again to select the ending point “B” and play the segment repeatedly. Press the A-B button again to cancel the repeat segment.

- 22 -

Playback Operation

This function is not available for JPEG disc.

Zoom

For DVD disc, press the ZOOM button to display the image as Q1-Q2-Q3-Q4-QOFF in sequence. For JPEG disc, press the ZOOM button enlarge and reduce the picture as follows: Q4/3-Q3/2-Q2-Q3-Q1/2-Q3/4-Qoff. For DIVX disc, press the ZOOM button to display the image as Q1-Q2-Q3-QOFF in sequence. During zooming, you can use the direction buttons to move the picture.

This function is not available for CD disc.

Backlight

Pressing this button will turn the LCD screen on or off. This function is useful when the player is connected to an external monitor or when playing CD and other discs. Turning the screen off while playing CD or other discs will conserve battery life.

INFO button

During playback, press the INFO button on theremote control for detailed information on the disc playing.

PIC button

Press the PIC button to change the level of brightness, color and contrast. Then use the +/- button on the front panel to adjust the value.

Keep press to shift aspect ratio between 16:9 and 4:3.

DVD Playback

Start playback

When the DVD menu appears, press the direction buttons () to select a feature.

Press ENTER or button to start playback.

Title Menu

Press TITLE button on the remote control to view the Title Menu during payback of a disc. Themenu will appear on the LCD screen.

- 23 -

Playback Operation

Press direction buttons () or the number buttons to select the title or disc option you wish to play. Press the ENTER button to start playback of a disc.

 This feature is not available on all discs.  Title and Menu are only available for DVD discs.

& Previous and Next

Press the  PREV button on the remote control, and playback will start from the previous track. Press the  NEXT button on the remote control and playback of the disc will start from the next track.

&Fast Forward & Rewind

Press the  and  buttons to Fast Forward or Fast Rewind a track on a disc during playback (x2, x4, x8, x16).

Slow Forward

Press the SLOW button to Slow Forward a track on a disc during playback (1/2, 1/4,1/6, 1/8).

Repeat

Continually pressing the REP button to select Repeat Chapter, Repeat Title and Off.

Subtitle

A DVD disc can be recorded with up to 32 subtitles. Press the SUBT button on the remote control during playback to select the one you

prefer.

 This function is available on a DVD that is recorded with multi-subtitles.

Audio

DVDs contain up to 8 audio bitstreams. For Example: English, French, etc. Press the AUDIO button on the remote control during playback to select the Audio

bitstream. The DVD Player will play the next audio bitstream every time you press the AUDIO button.

 This function is only available for discs that contain several audio bitstreams.

- 24 -

Playback Operation

Search by time

Press the GOTO button to select desired disc starting time, chapter or title. Press the GOTO button to display a menu on the screen:

Search: Time _ _:_ _:_ _ Title/Chapter _ _ _/_ _ _

Press the direction buttons to select the item you prefer, then use the number buttons to input the time (in the sequence of hour, minute and second) or the title/chapter

number you prefer. Press the ENTER button to confirm and it will start playback from the selected time or play the selected title/chapter automatically.

CD Playback

Load a CD disc into the disc tray, the playback will start automatically. Press the ENTER or button to start playback. Press the / button on the remote control

to stop playback.

&  Previous and Next

Press the  PREV button on the remote control, and playback will start from the previous track.

Press the  NEXT button on the remote control and playback of the disc will start from the next track.

&Fast Forward & Rewind

Press the  and  buttons to Fast Forward or Fast Rewind a track on a disc during playback (x2, x4, x8, x16).

Slow Forward

Press the SLOW button on the remote control to Slow Forward a track on a disc during playback (1/2, 1/4,1/8, 1/16).

Repeat Playback

Press the REP button to repeat Single,All and Off in sequence.

Search By Time

Press the GOTO button to select desired disc starting time, track starting time or track. During CD playback, press it once to display as follows:

Track Search: Time _ _:_ _:_ _ Track _ _ _

Press it again to display as follows:

Disc Search: Time _ _:_ _:_ _ Track _ _ _

Use 0-9 buttons on the remote control to select directly.

AUDIO button

Press the AUDIO button to select desired sound effect. Press it repeatedly and it will display as follows:

Left Right Stereo

Several seconds later, the display will exit from screen automatically.

- 25 -

Playback Operation

JPEG Playback

JPEG is a common picture format. Hundreds of pictures can be stored in a disc in this format.

Normal Playback

Load a JPEG disc into the DVD Player. After reading the disc, the DVD Player will display the images on the disc in sequence. Press the STOP button to return to the root menu. Press the TITLE button to enter the preview menu. Use the direction buttons to select the items you wish to view and then press the ENTER button to confirm and start playback. During playback of the disc, use the  and  buttons to select the picture forward and backward.

Picture Zooming and Moving

The ZOOM button is used to turn the zoom function on and off and move function. Press the ZOOM button on the remote control to enlarge the picture. During zooming status, you can use direction buttons to move the picture for viewing. When the ZOOM function is turned off, the picture will display normally.

 Some JPEG discs can be played normally but with no rotate or zoom functions

depending on how the disc was produced.

DIVX Playback

DIVX is the name of a revolutionary new video code which is based on the new MPEG-4 compression standard for video. You will be able to play DIVX movies using this DVD player.

1. Load a MPEG4 disc in the disc tray, the player will search and play disc automatically.

2. Press the STOP button to return to the root folder (menu). Use the  buttons

on the remote control to select desired file. Then press the ENTER or button to confirm your selection.

Pause

Press the button once to pause playback. Press the button again to resume normal playback.

Stop

During playback, pressthe STOP button once to return to the root menu. Press the button to resume normal playback.

- 26 -

Playback Operation

Previous and Next

Press the  button to go to the previous file. Press the  button to go to the next file.

Fast Playback

Press the  and  button to start fast forward and reverse playback during disc playing. Press it repeatedly to fast playback at the speed of 2X, 4X, 8X, 16X and

normal in sequence.

Press the MENU button during playback to return to root folder. Press the button to resume normal playback.

Repeat

During playback, press the REP button to repeat a file, folder in sequence. Press it repeatedly to display as follows: Repeat Single Repeat All Off.

Slow

Press the SLOW button repeatedly to start slow playback as following: s.f.1/2 – s.f.1/4 –s.f.1/6 – s.f.1/8 (s.f.: slow forward). Pressthe button to resume normal playback.

Goto

Press the GOTO button to select desired disc starting track or track starting time. During DIVX playback, press it repeatedly to display as follows:

Search: Time_ _:_ _:_ _ Track _ _ _. Press the 0-9 buttons directly to select according to your preference.

Press the ENTER button on the remote control to confirm.

Info

Press the INFO button for detailed information on the disc playing. Press it again to remove information from screen.

- 27 -

System Setup

Setup Menu

You can change the default settings to your own preference. Press the SETUP button on the remote control to display the settings menu. The menu includes Language setup, Video setup, Audio setup and Rating setup. Pressthe orbutton on the remote control to select a category.

Language Setup

Select Language. Press the ENTER button to enter the Language setup menu, the screen will displaythe following:

In this menu, use the  or button to select an item. Press the ENTER button to enter, use the  or button to select item. Press the ENTER button to confirm selection and return. Press the button to return to the previous menu.

OSD Menu

There are several OSD menu languages that can be selected such as English, Chinese, German, French, Spanish and Italian.

Subtitle

You can select English, Chinese, German, French, Spanish, Italy, Auto or OFF. Selecting Auto, the DVD Player will display the default subtitle on the screen. If the disc is without subtitles, during playback, no subtitle will be displayed. Select OFF and no subtitle will be displayed on the screen.

Audio

There are several audio languages available. You can select English, Chinese， German, etc.

Language Video Audio Rating

OSD Menu English Subtitle Auto Audio English

DVD Menu English Restore Default OK

- 28 -

System Setup

DVD Menu

There are several menu languages available. You can select English, Chinese， German, etc.

Restore Default

Select the item and press ENTER button to return to the original settings.

Video Setup

Press thebutton to select Video setup menu, then press the ENTER button to enter the menu. The screen will display the following:

Video System

You can select the video type between NTSC, PAL or auto.

TV Shape

You can select 4:3 PS, 4:3 LB or 16:9. Select the corresponding aspect ratio for your TV shape or DVD aspect ratio (Full Screen 4:3/ Wide Screen 16:9).

Close Caption

You can set the captions to ON or OFF during playback of a disc.

Audio Setup

Press the  button to select Audio setup menu. Press ENTER button to enter the menu. The screen will display the following:

Language Video Audio Rating

Video System NTSC TV Shape 16:9 Close Caption Off

Language Video Audio Rating

Downmix Stereo IR Off

- 29 -

System Setup

Downmix

You can select Stereo, Left, Right or Mix audio output mode.

This item is used to set the infrared audio signal to ON or OFF. When ON is selected, there will be infrared audio signal emitted from the infrared audio signal emitter. When OFF is selected, no infrared audio signal is emitted.

Rating Setup

Press thebutton to select Rating setup menu, then press the ENTER button to enter the menu. The screen will display as below:

In this menu, use the  or button to select an item. Press the ENTER button to enter, use the  or  button to select item. Press the ENTER button to confirm selection and return. Press the button to return to the previous menu.

Password

Parental control features are password protected. The original setting is unlocked. This setting allows you to use number buttons to input any password.

NOTE: The default password is 3308.

Rating

DVDs that are equipped with the child lock function are rated according to their contents and settings vary from disc to disc. Depending on the disc, you can replace or lock out violent scenes, or lock out playback of the disc altogether. Press the ENTER button to select. An interactive menu will appear on the screen.

DIVX registration

Display the information concerned with DIVX.

Language Video Audio Rating

Password --------Rating 8.Adult DIVX registration Display

- 30 -

Troubleshooting

Symptom What To Check

The DVD Player will not play.

• Make sure the AV IN/OUT switch ON the side of the player is in the OUT position for standard play.

• Make sure a disc is loaded.

• Make sure the disc isn’t loaded backwards.

• Disc should be clean and not warped.

• Player’s region code should be the same as region code of DVD disc.

• The DVD was exposed to humid conditions. If it has, remove the disc and keep the DVD Player powered up for at least two hours.

There is no sound.

• Make sure system connections are correct.

• Make sure the speakers are turned ON.

• Make sure the sound setup of DVD disc is correct.

• Is the disc dirty or warped? Clean or replace disc.

There is no picture.

• Make TV is turned ON and in correct video mode.

• Make sure your system connections are correct.

Poor AV performance. • Is your disc dirty or warped? Clean or replace disc.

Cannot continue to play or plays a section repeatedly.

• Make sure the player is not in A-B repeat status.

• PressA

-B button to cancel it A-B repeat status.

• Is your disc dirty or warped? Clean or replace disc.

There is no sound when using wireless headphone

• Make sure the IR is set to ON in the audio setup menu.

• Make sure the batteries of the headphone are fresh.

The remote control does not work.

• Make sure there aren’t any obstructions between the remote control and the DVD Player.

• Make sure you are pointing the remote control at the DVD Player.

• Make sure batteries are inserted correctly (check polarity).

• Replace weak batteries.

Other possibilities: Static or other external interference may cause the player to function abnormally. Unplug the power-supply cord from the outlet and plug it in again to reset the player so that normal operation can resume. If you are still having problems, then disconnect the power to the DVD Player and consult a qualified technician.

WARNING: Do not touch any metal objects to the Battery connectors, as it will put the Battery in standby mode. To exit the standby mode, connect the Battery and

DVD Player to AC or DC power.

- 31 -

Specifications

TFT Screen Size 7 inches Laser Wavelength Wavelength: 780/650nm

Video System NTSC/PAL Frequency Response 20Hz～20KHz ±2.5dB

Audio Signal-To-Noise Rate ≥ 75 dB Audio Distortion + Noise ≤ -70dB (1KHz) Channel Separation ≥ 70dB (1KHz) Dynamic Range ≥ 80dB (1KHz)

Audio Out Analog Audio Out

Out Level: 1.5V±

0.2

1.0

, Load: 10KΩ

Video Out Video Out

Out Level: 1V

P -P

±0.1, Load: 75Ω

Unbalanced Negative

Power AC100-240V～50/60Hz Power Consumption ＜13W Dimension w/o Battery 200mm×154mm×29mm (L/W/H) Weight w Battery About 0.68kg

DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

SEVIC SV070270D, VISION LIBERTY COMBO 2 Operating Manual

Specifications and Main Features

Frequently Asked Questions

User Manual