Page 1
Twin Topping Warmer | with Pump
MODEL:
TWIN FS COMPLETE BASE ONLY
120V USA 81220 81210
230V CONT. EUROPE 81250 81270
230V AUSTRALIA 81420 81430
230V UNITED KINGDOM 84910 84830
MODEL:
TWIN FS/FSP COMPLETE BASE ONLY
120V USA 81290 81210
230V CONT. EUROPE 80280 81270
230V AUSTRALIA 80850 81430
230V UNITED KINGDOM 84950 84830
MODEL:
TWIN FSP COMPLETE BASE ONLY
120V USA 81230 81210
230V CONT. EUROPE 81260 81270
230V AUSTRALIA 81460 81430
230V UNITED KINGDOM 84990 84830
Thank You
...for purchasing our topping warmer.
Its temperature sensing thermostat helps reduce
food costs while delivering a superior product.
SERVE BETTER WITH DISTINCTIVE DESSERTS
Page 2
SAFETY
According to food and safety regulations, most
foods must be stored and/or served at certain
temperatures or they could become hazardous.
Check with local food and safety regulators for
WARNING-
ELECTRICAL SHOCK COULD OCCUR
This unit must be earthed or grounded.
This requires all three prongs (terminals) on cord
plug to be plugged into power source.
specific guidelines.
Be aware of the product you are serving and the
temperature the product is required to maintain.
Server Products, Inc. can not be responsible for
the serving of potentially hazardous product.
PARTS
PARTS MAY VARY DEPENDING ON UNIT
FS FSP
LID
82509
PUMP
81320
Page 2
ADAPTER
82507
LADLE
82561
SPACER
82063
WATER
VESSEL
BASIN
BASE
(see cover
for part
number)
230V units include:
STAINLESS STEEL JAR
94009
Page 3
UNIT SET-UP
WASH ALL PARTS PROPERLY BEFORE EVERY USE. See page 6.
SEE SEPARATE PUMP MANUAL FOR PUMP INSTRUCTIONS.
FILL WATER VESSEL BASINS
1
• Fill 2.5 cups (20 oz/0.59 liter) of water up to
water level line inside each basin.
• Do not overfill.
TIP: Check water levels
throughout the holding period
to ensure even heating.
Filtered water is recommended
to deter corrosion.
INSERT SPACERS
2
PUT FOOD CONTAINERS
3
INTO WATER VESSEL BASINS
• Product being served must be
inside #10 cans or stainless steel jars.
Never place food directly into water
vessel basin of unit.
TIP: Simplify change-outs
with stainless steel jars.
Order item #94009.
INSTALL LID ACCESSORIES
4
OR PUMP(S)
PLUG CORD into power source.
5
PRESS SWITCHES to the “ON” position.
6
SET THERMOSTAT KNOBS
7
to food manufacturer’s recommended
serving temperature(s).
• Pull knobs out to turn and adjust.
• Push knobs in to lock.
• Dial indicators use increments of 5ºF.
• Thermostat range is 75º—210ºF.
(24º—99ºC)
• To heat unit faster, thermostat may
TEMPORARILY be rotated to maximum.
Page 3
Page 4
RETHERMALIZATION HOT FOOD HOLDING
Rethermalization of food products is achieved by
this appliance when it elevates the food product
temperature from a refrigerated 40°F (4°C) to a
safe serving temperature of 165°F (74°C) within a
period of 2 hours.
PRE-HEAT UNIT
1 1
for at least 5 minutes
• Correct amount of water in basin.
• Lid closed.
• Thermostat knob set at maximum setting.
ADD FOOD PRODUCT
2 2
• Put food container into the water
vessel basin.
• Maximum capacity of food product is
3 quarts (96 oz./12 cups). Do not overfill.
MAINTAIN SAFE
3
HOT FOOD HOLDING
•
After food reaches safe serving temperature
of 165°F (74°C), maintain product
temperature at or above 150°F (66°C).
• Adjust controller if needed to avoid
overheating food.
with:
NSF International and ANSI (American National Standards Institute) list the
Twin FS model as a “Rethermalization and Hot Food Holding unit (Standard 4).”
The Twin FS/FSP & Twin FSP models are listed as a “Rethermalization unit (Standard 4).”
Hot Food Holding is achieved with this appliance
when it maintains a food product temperature at or
above 150°F (66°C), in all locations throughout the
product, for a minimum of 2 hours, even if any lid,
cover, or pump is removed. The lid, cover, or pump is
recommended to help maintain product temperature.
PRE-HEAT UNIT
for at least 5 minutes
• Correct amount of water in basin.
• Lid closed.
• Thermostat knob set at maximum setting.
with:
ADD FOOD PRODUCT
• Put food which has already been
preheated to 150°F (66°C) into
container in water vessel basin.
• Maximum capacity of food product is
3 quarts (96 oz./12 cups). Do not overfill.
MONITOR FOOD CLOSELY FOR FOOD SAFETY.
The United States Public Health Service
recommends that hot food be held at a minimum
of 140°F (60°C) to help prevent bacteria growth.
COLD FOOD IS NOT TO BE ADDED TO THE
UNIT FOR RETHERMALIZATION WHILE HOT
FOOD IS BEING HELD.
SMART TIP
ALWAYS USE SPACERS
BENEATH FOOD CONTAINERS
Page 4
WITH SPACER
WITHOUT SPACER
Food may overheat from resting
on the bottom.
Water may overflow into food
container.
Excess product may be left in
food container.
Page 5
UNIT TAKE-DOWN
SEE SEPARATE PUMP MANUAL FOR PUMP INSTRUCTIONS.
PRESS SWITCHES to the “OFF” position.
1
UNPLUG CORD
2
CAUTION- HOT
Allow unit to cool before continuing.
REMOVE PUMP(S) OR LID(S)
3
REMOVE FOOD CONTAINERS
4
& SPACERS
EMPTY WATER FROM
5
WATER VESSEL BASINS
after each use.
TIP: Remember to empty the
water each day rather than add—
This will greatly extend the life
of your warmer.
DRY
6
thoroughly with a soft dry cloth.
Proper drying after each use helps
maintain the stainless steel.
Page 5
Page 6
CLEANING
SEE SEPARATE PUMP MANUAL
FOR PUMP INSTRUCTIONS.
WARNING-
ELECTRICAL SHOCK COULD OCCUR
• Electrical components of unit could be
damaged from water exposure or any liquid.
• Never immerse unit into water or any liquid.
• Never use any water jet or pressure sprayer
on unit.
• Ensure unit is “OFF” and unplugged.
CAUTION- HOT
Allow unit to cool before cleaning.
WASH REMOVABLE PARTS
1
• Before first use and after use daily,
disassemble and clean unit.
• Ensure unit is “OFF” and unplugged.
• Wash with dishwashing soap and hot water.
RINSE fully with clear water.
2
SANITIZE all parts according to local
3
sanitization requirements. All parts in contact
with food must be sanitized.
DRY all parts fully with a clean soft cloth.
4
CLEAN EXTERNAL SURFACES
5
• Wipe daily with a clean damp cloth.
• Dry with a clean soft cloth.
• Glass and surface cleaners approved for use
in food contact areas may be used.
CARE OF STAINLESS STEEL
This warmer and accessories are
constructed of stainless steel—
one of the best materials for food
serving and storage.
If you notice corrosion beginning on any stainless
steel surface, you may need to change the
cleansing agent, sanitizing agent, or the cleaning
procedures you are using.
Page 6
• A mildly abrasive nylon or brass brush may
be used to remove any stubborn food or
mineral deposits on interior surfaces of unit.
• Fully rinsing and drying all parts can help
prevent corrosion. Elements and minerals in
tap water can accumulate on stainless steel
parts and create corrosion.
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use products containing acids,
alkalines, chlorine, or salt. These agents can
corrode stainless steel.
• Do not use metal scrapers or cleaning pads
that could scratch surfaces.
Page 7
WIRING
G
2 1
2
1
UNIT 81210 | 120V | USA
1 8
BLACK
WHITE
REEN
7
9
Cord Assembly
1 6
Wire Assembly
2 7
Rocker Switch
3 8
Thermal Cutout
4 9
Thermostat
5
500W Heating Element
Wire Nut
Strain Relief Bushing
Hole Bushing
UNITS 81270, 81430, 84830 |
230V | CONT. EUROPE, AU, UK
2A 1A
2 3 4
2 1
N
BLUE
BROW
13
12
FLAG
2
FLAG
1
5
6
1
YELLOW
GREEN
2
4
3
2A 1A
2 1
2 1
5
FLAG FLAG
11
10
9 78
Cord Assembly
1
Bushing/Strain Relief
2
Thermal Cut-Out
3
Wire Assembly, 9"
4
Rocker Switch
5
Wire Assembly, 13”
6
Wire Assembly, 9”
7
500W Heating Element
8
Thermostat
9
Wire Assembly, 4"
10
Wire Assembly, 13"
11
Wire Assembly, 9"
12
Hole Bushing
13
6
Page 7
Page 8
TROUBLESHOOTING
UNIT DOES NOT HEAT?
• Ensure cord is securely plugged in.
• Ensure power is available from source.
• Ensure unit is on.
• Ensure thermostat knob is set correctly.
that the correct amount of water is in basin.
• Ensure
• Do not allow any of the electrical components
to get wet. Moisture may cause the unit to
trip breaker or GCFI. If moisture is suspected,
discontinue use. Allow unit to fully air dry.
SERVER PRODUCTS
LIMITED WARRANTY
Server Products equipment is backed by a
two-year limited warranty against defects in
materials and workmanship.
For complete warranty information go to:
www.Server-Products.com
PREVENT PITTING ON INSIDE
SURFACE OF VESSEL
• Empty water from water vessel basin each day.
• Thoroughly dry basin each day.
• If possible, use filtered water to fill vessel basin.
GENERAL SERVICE,
REPAIR OR RETURNS
Before sending any item to Server Products for service,
repair, or return, contact Server Products customer
service to request a Return Authorization Number.
Merchandise must be sent to Server Products with this
number. Service is extremely prompt. Typically, units
are repaired and ship out within 48 hours of receipt.
Merchandise being returned for credit must be in new
and unused condition and not more than 90 days
old and will be subject to a 20% restocking charge.
Electrical parts (thermostats, heating elements, etc.)
are not returnable.
Servicing Cord: Specific tools are required for safe
and proper power supply cord removal and installation.
If cord must be replaced, only a representative of the
OEM (original equipment manufacturer) or a qualified
technician may replace cord. Cord must meet code
designation H05 RN-F requirements.
NEED HELP?
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA
262.628.5600 | 800.558.8722
SPSALES@SERVER-PRODUCTS.COM
Page 8
Please be prepared with your Model, Part and
Series Numbers. This information and other
important data is located on the lid and/or base
of the unit.
Manual #01834-RevE 031517
Loading...