...for purchasing our InSweeten™ dispenser.
Now you can quickly deliver perfect portions
of bulk sweeteners with the push of the button
—equivalent to common portion packs.
PERFECTLY SWEETENED EVERY TIME!
Page 2
ASSEMBLY
SELECT PORTION TRIGGER
1
(if more than one is provided).
Trigger determines portion size dispensed.
WASH ALL PARTS
PROPERLY BEFORE USE. See page 5.
PORTION SIZETRIGGER
1/2 TSP
0.31 TSP
0.31 TSP
0.31 TSP
0.7 TSP
1 TSP
1 TSP
1 TSP
INSERT TRIGGER
2
With unit upside down on countertop, slide
spring end of trigger assembly into side slot.
Smooth side of trigger should face down.
INSTALL CLOSER PLATE
3
into unit body.
Hold closer plate by grasp tab.
Slowly push trigger assembly into unit body.
Ensure spring does not pop loose.
Insert closer plate rim tab into largest
interior opening of trigger.
WHITE
BLUE
PINK
YELLOW
WHITE
WHITE
GREEN
TAN
Portion size is also
stamped in trigger cavity.
Page 2
Page 3
INSTALL SPREADER
4
onto unit body,
rotating clockwise to tighten.
FILL UNIT
5
Flip unit right-side up and
add granular ingredient.
INSTALL LID
6
onto unit body,
rotating clockwise to tighten.
IMPORTANT: Refill
when product level
falls below fill line.
Page 3
Page 4
SAFETY
According to food and safety regulations, most
foods must be stored and/or served at certain
temperatures or they could become hazardous.
Check with local food and safety regulators for
specific guidelines. Server Products, Inc. cannot be
responsible for the serving of potentially hazardous
product.
DISASSEMBLY
REMOVE LID
1
EMPTY UNIT
2
Pour out any remaining ingredient.
IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly
to comply with local sanitization requirements.
NSF International listed.
REMOVE SPRING FROM TRIGGER
only if necessary for cleaning.
• Pry off spring with a flathead screwdriver.
• Push straight end of spring out of center groove
in circular tab of trigger.
3
4
5
Page 4
REMOVE SPREADER
REMOVE CLOSER PLATE
Set unit upside down on countertop.
Grasp tab of closer plate while holding
trigger in.
Pull closer plate up and out of unit.
Slowly release trigger to home position,
to ensure spring does not pop loose.
REMOVE TRIGGER ASSEMBLY
from side slot of unit.
RE-INSTALL SPRING
• Align straight end of spring into center groove in
circular tab of trigger.
• Use flathead screwdriver to press down on
straight end of spring.
• Snap spring into circular tab of trigger.
Page 5
CLEANING
WASH
1
After disassembly, wash all parts with
dishwashing detergent and hot water.
RINSE
2
Fully rinse all parts thoroughly with clear
water.
SANITIZE
3
all parts according to local sanitization
requirements. All parts in contact with food
must be sanitized.
AIR DRY
5
all parts fully before refilling.
YES!
Use dishwashing
soap and hot water
• Dishwasher safe
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use cleansing agents with high
concentrations of acid, alkaline or chlorine.
• Do not use metal scrapers or cleaning
pads that could scratch surfaces.
SERVER PRODUCTS
LIMITED WARRANTY
Server Products equipment is backed by a
two-year limited warranty against defects in
materials and workmanship.
For complete warranty information go to:
www.Server-Products.com
GENERAL SERVICE,
REPAIR OR RETURNS
Before sending any item to Server Products for service,
repair, or return, contact Server Products customer
service to request a Return Authorization Number.
Merchandise must be sent to Server Products with this
number. Service is extremely prompt. Typically, units
are repaired and ship out within 48 hours of receipt.
Merchandise being returned for credit must be in new
and unused condition and not more than 90 days old
and will be subject to a 20% restocking charge.
Page 5
Page 6
SWEETSTATION
™
RACKS
Lightweight, wall-mounted rack
securely holds dispensers in place
for single-handed operation.
Key slot mounting makes
removal easy.
SWEETSTATION™
RACK MOUNTING
• Select wall location or sturdy vertical surface
for mounting.
• Determine proper mounting hardware you will
need to supply.
• Consider best placement for ease of use.
• Locate (4) mounting holes 7" and 2-3/8"
apart as shown in diagram below.
SweetStation
Quad Shelf
87135
SweetStation
Triple Shelf
80085
™
™
2-3/8"
Page 6
7"
Registered trademarks of Sweet ‘N Low®, Splenda® and Equal® are property of their respective owners.
Page 7
TROUBLESHOOTING
INCONSISTENT PORTIONS?
Heat and moisture can cause ingredients
to settle and become packed in.
• Shake unit to dislodge light clumping.
• Ensure ingredients have not become clogged
within the unit—disassemble and inspect.
• Clean unit and air dry fully before refilling.
• Ensure ingredient level is above fill line.
TRIGGER WON’T PUSH IN?
• Ensure closer plate is properly installed with
rim tab in the largest opening of trigger.
NOYES
Please Visit
www.YouTube.com/user/ServerProducts
to see videos of more information.
Page 7
Page 8
INSWEETEN™ INDIVIDUAL PARTS
LID
87883
AVAILABLE
BODIES
14 OZ. BODY
87163
24 OZ. BODY
87162
CLOSER PLATE
87095
AVAILABLE
TRIGGER ASSEMBLIES
PORTION SIZETRIGGERPAR T
1/2 TSP
0.31 TSP
0.31 TSP
0.31 TSP
0.7 TSP
1 TSP
1 TSP
1 TSP
WHITE
BLUE
PINK
YELLOW
WHITE
WHITE
GREEN
TAN
NEED HELP?
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA
262.628.5600 | 800.558.8722
SPSALES@SERVER-PRODUCTS.COM
Page 8
SPREADER
87156
87177
87178
87179
87181
87176
87173
87174
87175
Please be prepared with the Part Numbers for your
items. Individual part numbers are listed above.
Manual #01695-RevD 102416
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.