Page 1
User Manual
Manuel de l’utilisateur
Guía delusuario
E11-G13- element classic
Z02-Hub –Sengled Hub
LED + Smart Control
Page 2
System Features:
Control Element lighting from anywhere at anytime
•
Schedule scenes based on timing, brightness and
•
•
View current power and historic energy consumption.
•
Control Sengled Element bulbs via local Wi-Fi network or Sengled
cloud
•
Track and report number of power cycles and usage hours
Element Bulb Features
•
Wireless control
•
Dimmable via Element app
•
Support for warm white 2700K color temperature
25,000 hour LED lifetime
•
Wide beam angle
•
Supports Zigbee HA 1.2.1
Element Hub Features:
•
Connects up to 50 Element bulbs via the Element mobile app
•
Wirelessly control groups and individual Element bulbs
•
Supports Zigbee HA 1.2.1
Element Bulb Specification
Model: E11-G13
•
Power: 9.0W
•
Brightness: 800 lumens
•
Beam Angle: 220°
•
Input: 100-130V AC, 50/60Hz, 85mA
•
Light Socket: E26
•
Operating Temperature: -4 °F ~ + 104 °F (-20
•
•
Storage Temperature: -40 °F ~ + 158 °F (-40
•
Operating Humidity: 10% ≤ RH ≤ 95%, non-condensing
•
Dimensions: Dia: 2.4in (61.5mm); H: 4.4in (112mm)
Element Hub Specification
•
Model: Z02-hub
•
Input: 5V DC, 300mA
•
Adapter Input: 100-240V AC, 30mA; Output: 5V DC, 1A
•
Dimensions: L: 78mm; W: 78mm; H: 26mm
•
Support Zigbee HA 1.2.1 and 2.4 GHz Wi-Fi
Box Contents
Two Element A19 Bulbs and One Hub
•
One Ethernet Cable
•
Quick Start Guide
•
User Manual
•
Limited Written Express Warranty
•
°C
~ + 40 °C)
°C
~ +70 °C)
EN
Page 3
EN
Local Operations
*To ensure the following steps work successfully, please power
on the bulb first and wait for at least four seconds before taking
any of the steps.
Reset the hub: The hub has to be reset when changing Wi-Fi
networks. Press and hold the white round button on the side of the
hub for at minimum eight seconds and then release it, the middle
blue signal indicator light on the front of the hub should flash eight
times if the reset is successful. Wait for up to 30 seconds for the
indicator light to steady.
Rejoin wireless network from the bulb: Power cycle the bulb (off
then back on) five times quickly. The bulb will blink two times
indicating network rejoin.
Reset factory default for the bulb: Power cycle the bulb (off then
back on) quickly for at minimum ten times. The bulb will blink five
times indicating pairing mode.
EZ-Mode commissioning from the bulb: Power cycle the bulb (off
then back on) seven times quickly to enable EZ-Mode. The bulb will
blink to indicate that it is in this mode for three minutes. To exit this
mode earlier, power off the bulb via the wall switch, wait for two
seconds and then power it back on.
System Setup Instructions
Please review the Quick Start guide for instructions on how to
•
set up the Element Hub
•
Please contact customer service via Sengled.com for
information on how to purchase additional bulbs. To add
additional bulbs, please follow the in-app instructions to scan,
power on and add the bulbs to their desired hub as shown below
Page 4
•
NOTE: Bulbs associated with another Sengled account must
first be deleted and factory reset. Refer to the Local
Operations section of the User Manual for instructions on
how to factory reset a bulb.
•
NOTE: Bulbs accidentally deleted from a Sengled account
must first be factory reset before being re-added.
Add Bulbs
Device detail Add Bulb
Scan code Mac address
(1)
(2)
Add Bulb
EN
(3)
(4)
Important Safety Instructions
This product is intended for indoor use only
•
Do not install the product near any heat sources, such as
•
heaters, radiators, stoves, heat registers or other apparatus
that produce heat
To reduce the risk of electric shock, do NOT disassemble.
•
There are no serviceable parts inside
Do not clean the device when it is on and connected to the
•
power supply
Page 5
For best protection against lightning,unplug or unscrewth-
EN
•
eproducts from its power source duringa storm
The bulb will be hot when in use and should not be touched
•
without taking care
Do NOT throw the LED bulb into regular trash at the end of
•
its life. Bring the bulb to a local recycling center for proper
disposal
CAUTION:
NOT FOR EMERGENCY LIGHTING
RISK OF ELECTRIC SHOCK-DO NOT USE WHERE DIRECTLY
EXPOSED TO WATER
E11-G13
FCC ID：2AGN8-E11G13 IC：20888-E11G13
Z02-hub
FCC ID：2AGN8-Z02HUB IC：20888-Z02-HUB
Federal Communications Commission (FCC)
Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generate, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
Page 6
EN
FCC Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment.
This equipment must be installed and operated in accordance
with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be collocated or
operating in conjunction with any other antenna or transmitter.
IC Radiation Exposure Statement for Canada
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent is otropically
radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Conformément à la réglementation d'Industrie Canada, le présent
émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et
son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement
d'une communication satisfaisante.
User manuals for transmitters equipped with detachable antennas
shall also contain the following notice in a conspicuous location:
This radio transmitter (identify the device by certification number,
or model number if Category II) has been approved by Industry
Canada to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for
each antenna type indicated. Antenna types not included in this
Page 7
list, having a gain greater than the maximum gain indicated for
EN
that type, are strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro
de certification ou son numéro de modèle s'il fait partie du
matériel de catégorie I) a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et
ayant un gain admissible maximal et l'impédance requise pour
chaque type d'antenne. Les types d'antenne non inclus dans cette
liste,ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with “Industry Canada RSS-102 for
radiation exposure limits set forth for an uncontrolled environment”.
This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
© 2016 Sengled, Incorporated. All rights reserved. Sengled
Element is a trademark of Sengled, Incorporated, registered in
the United States and other countries. Specifications are
subject to change without notice. Other trademarks and trade
names are the property of their respective owners.
Page 8
Rev 1.1 2016.04
© 2016 Sengled, Incorporated. All rights reserved.
www.sengled.com
Loading...