Sencore Impulse User Manual
1
User Manual
2
V1.0
About Manual
This manual describes the detailed installation, setup and operation of the Sencore
impulse. Read carefully to make sure all steps are completed properly. For additional
support assistance, visit www.sencore.com/support.
Important
To avoid injury or product damage, make sure to review and understand all safety
instructions.
Use a quality cabling and make sure the connections are in good operating
condition. Use
provided power supply, or one with an equivalent rating. Do not open the device as it
may result in electrical shock to the user.
Specifications and functions may be changed for
improvement without
advanced notification.
Notices
Trademark Acknowledgments
All trademarks shown in this manual are trademarks of their respective owners.
Publication Disclaimer
Sencore assumes no responsibility for errors or omissions that may appear in this
publication. We reserve the right to change this publication at any time without notice.
This document is not to be construed as conferring by implication, estoppel, or
otherwise any license or right under any copyright or patent, whether or not the use of
any information in this document employs an invention claimed in any existing or later
issued patent.
Copyright
Information in this publication is subject to change without notice. No part of this
publication may be reproduced or transmitted in any form, by photocopy, microfilm,
xerography, or any other means, or incorporated into any information retrieval system,
electronic or mechanical, for any purpose, without the express permission of its owner.
3
Safety Instructions
Respect all warning symbols to avoid personal injury. Before you work on any
equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing injury.
Electric Shock Hazard
This equipment meets applicable safety standards. Refer to this equipment's
Identification label or contact factory for details about regulatory compliance
approvals.
Electric shock can cause personal injury or even death. Avoid direct contact with
dangerous voltages at all times. The protective ground connection, where
provided, is essential to safe operation and must be verified before connecting
the power supply.
Heed the following safety warnings and guidelines:
• Only trained and qualified personnel should be allowed to install, replace,
or service this equipment.
• Only qualified service personnel are allowed to remove chassis covers.
Any repairs should be performed by the factory.
• No user-serviceable parts inside. Do not open.
Important Safety Reminders
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this device near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with
Sencore’s instructions.
• Do not install near any heat sources such as radiators, heat registers,
stoves, or other devices (including amplifiers) that produce heat.
• Protect the power cord from being walked on or pinched particularly at
wall plugs, convenience receptacles, and the point where they exit from
the device.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the device. When a cart is used, use caution
when moving the cart-device combination to avoid injury from tipping
over.
WARNING:
4
• Use quality surge suppression device to prevent damage during lightning
storms.
• Refer all servicing to qualified service personnel. Servicing is required
when the device has been damaged in any way, such as damage to
power-supply cord, liquid has been spilled or objects have fallen into the
device, the device has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Installation Site
When selecting the installation site, comply with the following:
• Protective Ground - The protective ground lead of the building's electrical
installation should comply with national and local requirements.
• Environmental Condition - The installation site should be dry, clean, and
ventilated. Do not use this equipment where it could be at risk of contact with
water.
Installation Requirements
Installation of the equipment must comply with local and national electrical codes.
WARNING:
5
Content
!
About This Manual ................................................................................................... 2
Important ..................................................................................................................... 2
Notices ......................................................................................................................... 2
Trademark Acknowledgments ..................................................................................... 2
Publication Disclaimer .................................................................................................. 2
Copyright ..................................................................................................................... 2
Important Safety Reminders ......................................................................................... 3
Installation Site ............................................................................................................ 4
Installation Requirements ............................................................................................ 4
1
Overview ................................................................................................................... 6
1.1
General ............................................................................................................... 6
1.2 Architecture
.......................................................................................................... 6
2
Installation ................................................................................................................. 7
2.1
Introduction ......................................................................................................... 7
2.2
Installation Preparation ....................................................................................... 7
2.3
Equipment Wiring and Connection ....................................................................... 7
2.3.1
Power Connection ......................................................................................... 7
2.3.2
Connection Setup for Web Management ....................................................... 7
3
Operation Guide ........................................................................................................ 7
3.1
Powering Up and Initialization ............................................................................ 7
3.2
Operating the Front Panel Interface ................................................................... 8
3.3
Operating the Web Interface ................................................................................ 8
3.3.1
Access Interface PC Web-UI ........................................................................ 8
3.3.2
Status ............................................................................................................ 9
3.3.3
Broadcast/Live Stream Settings .................................................................. 10
3.3.4
Record Settings ........................................................................................... 12
3.3.5
System Setting ............................................................................................ 12
3.4
YouTube Streaming .......................................................................................... 14
Loading...