(+) Button - Increase the volume
(-) Button - Decrease the volume
Battery Check
Phone, Music Pairing
1. Press the Center Button for 12 seconds.
2. Press the (+) Button to enter into Phone Pairing
3. Search for Bluetooth devices on your mobile phone. Select the X-COM2 in the list of the devices
detected on the mobile phone.
4. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
Music Operation
Play or pause music: Press the Center Button for 1 second.
Track back: Press the (-) Button for 1 second.
Track forward: Press the (+) Button for 1 second.
Mobile Phone Call Making and Answering
Answering a call: Tap the Center Button
Ending a call: Press the Center Button for 2 seconds.
Voice dial: Press the Center Button for 3 seconds.
Speed dial: Press the (+) Button for 3 seconds.
Rejecting a call: Press the Center Button for 2 seconds.
Intercom Pairing
1. Press and hold the Center Button of two headsets for 5 seconds until red LEDs of both units start
to flash rapidly.
2. Simply tap the Center Button of any one of the two headsets.
Intercom Start/End
1st Friend: Tap the Center Button once.
2nd Friend: Tap the Center Button twice.
3rd Friend: Tap the Center Button triple times
Radio On/Off
Turn on the FM radio: Press the (-) Button for 1 second.
Turn off the FM radio: Press the (-) Button for 1 second.
Radio Scan Up FM Band
Start scanning: Press (+) Button for 1 second.
Stop scanning: Press (+) Button for 1 second.
Save presets while scanning
Save presets: Tap the Center Button
Radio Move to Preset Station
Move to next preset: Press the Center Button for 1 second (1 → 2 → … → 10)
Radio Seek Stations
Seek up stations: Double tap the (+) Button.
Seek down stations: Double tap the (-) Button.
Setting
Configuration Menu: Press the Center Button for 10 seconds.
Using the Sena Device Manager
Connect the headset to your computer via a USB cable. Launch the Sena Device Manager and click
DEVICE SETTING to configure the headset settings.
For details about downloading the Sena Device Manager, please refer to the leaflet included in the package.
Using the Sena Utility App
1. On your smartphone, download the Sena Utility App for Android or iPhone from Google Play or
App Store. Please refer to Sena.com for more details.
2. Pair your smartphone with the headset.
3. Run the Sena Utility App. Swipe the screen to the right and tap Setting to configure the headset
settings.
Troubleshooting
Factory Reset
If you want to restore the X-COM2 to factory default settings, use the Factory Reset in the configuration
menu. The headset automatically restores the default settings and turns off.
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antennae
-Increase the separation between the equipment and the receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that may cause undesired operation of
the device.
FCC, IC RF Exposure Statement
This equipment complies with FCC, IC radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying RF exposure compliance. The
antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter,
except in accordance with FCC, IC multi-transmitter product procedures.
The distance between the antenna of the device and the head surface is at least 10mm and user 10mm
or more.
The highest SAR value reported under this standard during product certification for use next to the head
with the minimum separation distance of 10mm is below 1.09 W/Kg.
This product is compliance to FCC, IC RF Exposure requirements and refers to FCC website
https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: S7A-SP65, IC:8154A-SP65.
FCC, IC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for
compliance could void user’s authority to operate the equipment.
Certification et homologation de sécurité Déclaration de conformité FCC
Cet appareil est en conformité avec la partie 15 des règles de la FCC. Son fonctionnement est soumis
aux deux conditions suivantes :
(1) Cet appareil ne doit pas créer d’interférences préjudiciables et
(2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son
bon fonctionnement.
Cet équipement a été testé et jugé conforme aux limites pour un appareil numérique de classe B,
conformément à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection
raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère
et utilise de l’énergie radio fréquence et, s’il n’est pas installé et utilisé conformément. aux instructions, il
peut occasionner des interférences nuisibles au niveau des communications radios. Cependant, il
n’existe aucune garantie que ces interférences ne se produiront pas dans une installation particulière. Si
cet équipement génère des interférences nuisibles à la réception de la radio ou de la télévision (ce qu’il
est possible de déterminer en mettant l’équipement hors tension, puis sous tension), l’utilisateur est invité
à suivre une ou plusieurs des mesures suivantes pour corriger le problème des interférences en prenant
l’une des mesures suivantes :
-Modifier l’emplacement ou l’orientation de l’antenne de réception.
-É loigner l’appareil du récepteur.
-Brancher l’appareil sur une prise située sur un circuit différent de celui du récepteur.
-Consulter le revendeur ou un technicien expérimenté pour obtenir de l’aide.
É noncé FCC sur l’exposition aux radiations RF
Cet équipement est conforme aux réglementations FCC d’exposition aux radiations définies pour un
environnement non contrôlé. Les utilisateurs doivent respecter les instructions d’exploitation spécifiques
pour répondre aux exigences de conformité sur l’exposition aux RF. L’antenne utilisée pour cet appareil
ne doit pas fonctionner en même temps qu’une autre antenne ou émetteur, sauf s’il y a conformité avec
les procédures FCC des produits multi-émetteurs.
Énoncé d'Industrie Canada(IC)
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisee aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est
susceptible d’en compromettre le fonctionnement.
FCC, IC RF Exposure Statement
Cet équipement est conforme aux limites d'exposition aux radiations de la FCC, IC définies pour un
environnement non contrôlé. Les utilisateurs finaux doivent suivre les instructions d'utilisation spécifiques
pour satisfaire à la conformité d'exposition RF. L'antenne utilisée pour cet émetteur ne doit pas émettre
simultanément avec d'autres antennes ou émetteurs, sauf en conformité avec les procédures FCC, IC
relatives aux produits multi-émetteurs.
La distance entre l'antenne de l'appareil et la surface de la tête est d'au moins 10 mm et l'utilisateur de 10
mm ou plus.
La valeur SAR la plus élevée signalée en vertu de cette norme pendant la certification du produit devant
être utilisée à côté de la tête avec la distance minimale de séparation de 10 mm est inférieure à 1,09
W/Kg.
Ce produit est conforme aux exigences de la FCC, IC en matière d'exposition aux radiofréquences et
renvoie au site Web de la FCC à l'adresse https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm.
Recherche de l'ID FCC: S7A-SP65, IC: 8154A-SP65.
Précautions FCC , IC
Tout changement ou modification non expressément approuvé par la partie chargée de la mise en
conformité peut annuler le droit de l’utilisateur à utiliser l’équipement.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.