SENA TECHNOLOGIES SP45 User Manual

SP45 (Momentum CAM) Manual

1. GETTING STARTED

1.1 Powering On and Off

Press and hold the Center Button for 3 second to turn the headset on or off.

1.2 Charging

1. Plugged into a computer’s USB port.

2. With a USB-equipped AC adapter via a wall-outlet charger.

Note: Please make sure to take off your helmet while charging. The headset automatically turns off during charging.

Depending upon the charging method, fully charged in about 2.5 hours.

1.3 Checking the Battery Level

There are two ways to check battery level:

1. Visually, with LEDs when powering on.

please visit sena.com.

1.5.2 Sena Smartphone App

The Sena Smartphone App allows you to configure settings, as well as access the User’s and Quick Start Guides.

To do so, pair your mobile phone with your Momentum Helmet. Run the Sena Smartphone App and configure

the settings directly from your smartphone. You can download the Sena Smartphone App for Android and Apple

operating systems.

2. CAMERA OPERATION

2.1 Camera On and Off

To turn on the camera, tap the Camera Button. The camera turns off automatically after five minutes of inactivity.

To turn off the camera manually, press and hold the Camera Button for 3 seconds.

2.2 Video Recording

To record a normal video, set the video mode setting in the camera configuration to be video mode. Press and

hold the Camera Button for 1 second to start video recording. The green LED will flash and you will hear a voice

prompt, “Recording”. Press and hold the Camera Button for 1 second to stop recording.

2.3 Loop Recording Mode

Loop Recording mode continuously records videos to create footages of assigned length of time. If the memory

reaches maximum, then the oldest footage will be deleted to store the most recent footage. To use loop recording,

set the video mode setting in the camera configuration to be loop recording mode. Press and hold the Camera

Button for 1 second to start recording. The green LED will flash and you will hear a voice prompt, “Recording”.

Press and hold the Camera Button for 1 second to stop recording. You will hear a voice prompt, “Recording

stopped”.

.3. MAINTENANCE AND CARE

3.1 Outer Shell

Use a soft cloth and a small amount of water to remove bugs from the exterior.

Note: Never use gasoline, diesel fuel, thinners or solvents to clean the helmet. These substances can cause serious

damage to the helmet, even though the resulting damage may not be visible. The full safety function of the helmet

can then no longer be guaranteed.

3.2 Inner Lining

The inner lining of the Helmet is completely removable. Its headliner can be washed by hand using mild soap at a

maximum temperature of 30°C (86°F). Allow the lining to dry at room temperature.

3.3 Storing the Helmet

Store the helmet in a dry, dark, well-ventilated location, out of the reach of children and animals. Always position

the helmet so that it cannot fall to the floor. Damage that occurs in this way is not covered by the warranty.

Safety Precautions

Please ensure that the product is properly used by observing the warnings and cautions below to
prevent any risk and/or damage to property.

Product Storage and Management

• Keep the product free of dust. It may damage mechanical and electronic parts of the product.

• Do not store the product in high temperatures as this may reduce the life span of electronic
devices, damage the battery, and/or melt plastic parts of the product.

• Excessive heat (e.g. exhaust heat) can cause damage to the decoration, the inner shell of the
helmet and the interior lining.

• Do not store the product in cold temperatures. Abrupt changes in temperatures may cause
condensation and damage electronic circuits.

• Do not clean the product with cleaning solvents, toxic chemicals, or strong detergents as this
may damage the product.

• Direct contact with motor fuel, thinners or solvents can destroy the structure of the inner and
outer shell. Make sure the helmet does not come into contact with such substances, even for
cleaning purposes.

• Do not paint the product. Paint may obstruct moving parts or interfere with the normal operation
of the product.

• Do not drop or otherwise shock the product. It may damage the product or its internal electronic
circuits.

• Do not disassemble, repair or modify the product as this may damage the product and invalidate
the product warranty.

• Do not store the product in humid environments, especially for long time storage.

• The helmet should be replaced after 5 to 7 years, depending on use and care. Although the outer
shell is in principle capable of a longer service life, the occurrence of material fatigue and wear to
other components, as well as the overall action of the helmet and the unknown conditions in which
the helmet has been used, make it advisable for your own safety to replace the helmet after this
period of use.

• Original components (in particular on the outer shell, inner shell and restraint system) should not
be altered or removed. The fitting of additional parts from other manufacturers that have not been
recommended can reduce the protective effect and renders the DOT certification and all warranty
and insurance claims invalid.

• Use only original parts, replacement parts and accessories that Sena has expressly approved for
your helmet.

Product Use

• Motorcycling is associated with particular risks and dangers for the rider and passenger. These
risks and dangers can be reduced, but not eliminated completely, by wearing a helmet. It is
impossible to state precisely what the protective effect of a helmet will be in the event of an
accident. Safe riding techniques, adapted to the particular road and weather conditions, are
essential for your safety.

• To provide adequate protection, the helmet must fit well and be securely fastened.

• Always fasten the chinstrap before setting off and check that the fastening system and strap are
correctly in position.

• Never ride with the chinstrap unfastened or incorrectly adjusted. The chinstrap must be correctly
positioned and must not come loose when pulled. The fastener is not correctly closed if the
chinstrap becomes loose when pulled.

• The full protective function of a helmet can no longer be guaranteed after an accident or impact.
Like the crumple zone of a car, the impact energy of a collision is absorbed by complete or partial
destruction of the structure of the outer and/or inner shell of the helmet. Because of the way
helmets are designed, this damage is rarely visible from the outside. The safety helmet is
designed to absorb only one impact. It is therefore essential to replace the helmet after a fall,
accident or other violent impact. For safety reasons, the old helmet should be rendered unusable.

• The helmet safety mechanism described above can also cause small cracks in the shell when
the helmet is dropped from a small height (less than 1 meter).

• Any helmet that has been subjected to a violent impact should be replaced.

• No helmet provides absolute protection from all conceivable impacts. This helmet has been
specially developed for motorcycle riding and is unsuitable for other purposes.

• Examine the helmet for damage at regular intervals. Small scratches will not impair the protective
function of your helmet.

• In some regions, it is prohibited by law to ride motorcycles while wearing headsets. Therefore be
certain to comply with all relevant laws in the region before using the product.

• Use of the product at a high volume for a long period of time may damage your eardrums or
hearing ability. Keep the volume at a modest level to prevent damage.

• Do not cause impact to the product or touch it with sharp tools as this may damage the product.

• Do not use the product in high-temperatures or apply heat to the product as this may cause
damage, explosion, or fire.

• Keep product away from pets or small children. It may damage the product.

• In any place where wireless communication is prohibited, such as hospitals or airplanes, turn off
the power and refrain from using the product. In a place where wireless communication is
prohibited, electromagnetic waves may cause hazards or accidents.

• Do not use the product near hazardous explosives. When it is near any explosion hazards, turn
off the power and heed any regulations, instructions, and signs in the area.

Battery

This product has an irreplaceable rechargeable battery inside. Therefore, when using the product,
make sure to adhere to the following:

• Never separate the battery from the product as this may damage the product.

• The battery performance may be reduced over time with usage.

• In recharging the battery, make sure to use an approved charger provided by the manufacturer.
Use of a non-approved charger may cause fire, explosion, leakage, and other hazards may also
reduce the life time or performance of the battery.

• Any 3rd party USB charger can be used with Sena products if the charger is approved by either
the FCC, CE, IC or other locally approved agencies that Sena accepts.

• Store the battery at temperatures of 15°C~25°C (59°F~77°F). Higher or lower temperatures may
reduce the capacity and life of the battery, or may cause temporary non-operation. Do not use the
product in sub-zero temperature, because it may cause serious reduction of the battery
performance.

• If you apply heat to the battery or throw it into a fire, it may explode.

• Do not use the product with a damaged battery. It may explode and/ or cause accidents.

• Never use a damaged charger. It may explode and/or cause accidents.

• Battery life may vary depending on conditions, environmental factors, functions of the product in
use, and devices used with it.

Certification and Safety Approvals
FCC Compliance Statement

This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,