SENA TECHNOLOGIES SP29 User Manual

FreeWire

Bluetooth CB and Audio Adapter

SENA www.sena.com User’s Guide

CONTENTS

1. INTRODUCTION

2. PACKAGE CONTENTS

3. INSTALLING THE FREEWIRE

3.1 Installing on the Handle Bar

3.2 Placing on the Mounting Cradle

4. POWERING ON/OFF AND CHARGING

4.1 Powering On

4.2 Battery Check

4.3 Charging

5. PAIRING THE FREEWIRE WITH BLUETOOTH DEVICES

6. USING THE FREEWIRE

6.1 Connections

6.2 Using with a headset

6.4 Reset to Factory Default Settings

6.5 Fault Reset

7. QUICK REFERENCE
BATTERY INFORMATION
MAINTENANCE AND CARE
DISPOSAL
CERTIFICATION AND SAFETY APPROVALS

FCC Compliance Statement
FCC RF Exposure Statement
FCC Caution
Bluetooth License

WAIVER AND GENERAL RELEASE

Limitation of Liability
Return for Full Refund

WARNING

© 1998-2016 Sena Technologies, Inc. All rights reserved.
Sena Technologies, Inc reserves the right to make any changes and improvements to its product without providing prior
notice.

Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. FreeWire™, Prism™, Bluetooth
Audio Pack for GoPro®, Tufftalk™, 20S™, 10S™, 10C™, 10U™, 10R™, 3S™, SMH10™, SMH10R™, SMH5™, SMH5-FM™,
SMH3™, SPH10™, SPH10H™, SPH10H-FM™, SPH10S™, Expand™, Bluetooth Mic&Intercom™, Handlebar Remote™, Wristband
Remote™, SM10™, SR10™, SR10i™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be

used without the express permission of Sena.

GoPro® is a registered trademark of Woodman Labs of San Mateo, California. Sena Technologies, Inc. (“Sena”) is not affiliated with
Woodman Labs. The Sena Bluetooth Pack for GoPro® is an after-market accessory specially designed and manufactured by Sena
Technologies, Inc. for the GoPro® Hero3 and Hero4 allowing for Bluetooth capabilities. Harley-Davidson® is a registered trademarks of
H-D Michigan, Inc. and Harley-Davidson, Inc. Honda® and Gold Wing® are trademarks of Honda Motor Co., Ltd. Sena is not affiliated
with Harley-Davidson, H-D Michigan, Inc. or Honda Motor Co., Ltd. Other trademarks and tradenames are those of their respective
owners.

The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received. Including interference that may cause undesired operation

Note : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

ÿ Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisee aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en
compromettre le fonctionnement. ÿ

Caution: Any changes or modifications in construction of this device which are not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.

Hereby, SENA TECHNOLOGIES.Inc Declares that this Freewire is in compliance with the essential requirements and

other relevant provisions of directive 1999/5/EC.

1. INTRODUCTION

Thank you for choosing the Sena FreeWire. The FreeWire is a Bluetooth CB radio and audio adaptor. You can connect
the FreeWire to the motorcycle onboard audio system and make the audio system transfer stereo audio (music, FM radio,
navigation etc.) to a Sena Bluetooth headset.

You can communicate through the built-in CB radio in the onboard audio system using the FreeWire. Also, if you have a
mobile phone connected to the motorcycle onboard audio system by a cable, you can have mobile phone calls using your
headset.

When a rider and a passenger connect the FreeWires to each port and pair a Sena headset to each FreeWire, they can

communicate with each other using the bike’s internal communication network.

Please read this User’s Guide carefully before using the FreeWire. Also refer to www.sena.com for the latest version of
the User’s Guide and additional information related to Sena Blueooth products.

The FreeWire Features:

● Support for onboard built-in CB radio communication

● Wirelessly stream stereo audio to Sena Bluetooth headset

● Support for internal communication between a rider and a passenger each using a FreeWire

● AUX input for GPS, radar detector or laser detector

● Mix the audio sources from the AUX input and the onboard audio system

● 12V bike-powered kit with On/Off controlled by the ignition switch

● Firmware upgradeable

Technical Specifications:

● Bluetooth 4.1

● Advanced Audio Distribution Profile (A2DP)

● Operating time: 7 hours

● Battery charging time: 2.5 hours

● Lithium polymer battery

● Dimensions: 83 mm X 45 mm X 25 mm (3.3 in X 1.8 in X 1.0 in)

● Weight: 50 g (1.76 oz)

● CE, FCC, IC

2. PACKAGE CONTENTS

2.1 FreeWire for Harley-Davidson Package

• Main Unit

• Handlebar Mounting Kit

• Mounting Cradle

• USB Power & Data Cable (Micro USB type)

• Micro USB to 7 Pin DIN Cable for Harley-Davidson

• 3.5 mm Stereo Audio Cable - Straight

• Cigarette Charger (Jack Type)

2.2 FreeWire for Honda Goldwing Package

• Main Unit

• Handlebar Mounting Kit

• Mounting Cradle

• USB Power & Data Cable (Micro USB type)

• Micro USB to 5 Pin DIN Cable for Honda Goldwing

• 3.5 mm Stereo Audio Cable - Straight

• Cigarette Charger (Jack Type)

3. INSTALLING THE FREEWIRE

3.1 Installing on the Handlebar

1. Attach the mounting kit on the back of the FreeWire along the guide rail.

2. Place the main unit on the handlebar, wind the rubber band around the handlebar, and hang it on the hook.

3.2 Placing on the Mounting Cradle

1. Locate a proper surface on your motorcycle body, clean the body surface location with a moistened towel, and

allow to dry thoroughly.

2. Peel off the cover of the adhesive tape of the mounting cradle and attach the unit on the proper surface of your

motorcycle.