2.4 Checking the Bluetooth Module’s
Battery Level 14
2.5 Volume Adjustment 15
2.6 Downloadable Sena Software 16
2.6.1 Sena Device Manager 16
2.6.2 Sena Smartphone App 16
2.7 Configuration Menu 16
3. PAIrING THE HELmET wITH
OTHEr BLuETOOTH DEvICES 21
3.1 Mobile Phone 21
3.2 Additional Mobile Phones, GPS, MP3
Player or Sena SR10 Two-Way Radio
Adapter 22
3.3 Advanced Selective Pairing:
Hands-Free or A2DP Stereo 23
TABLE OF CONTENTS CONTINUED
3.3.1 Phone Selective Pairing —
Hands-Free Profile 23
3.3.2 Media Selective Pairing —
A2DP Profile 24
4. mOBILE PHONE uSAGE 26
4.1 Making and Answering Calls 26
4.2 Speed Dialing 26
4.2.1 Assigning Speed Dial Presets 26
4.2.2 Using Speed Dial Presets 29
5. STErEO muSIC 32
5.1 Playing Music with Bluetooth Devices 32
5.2 Music Sharing 33
5.3 Audio Boost (Default: Enable) 34
6. INTErCOm SETuP 35
6.1 Intercom Pairing 35
6.2 Two-Way Intercom 37
6.3 Multi-Way Intercom 38
6.3.1 Starting a Three-Way Intercom
Conference 38
6.3.2 Starting a Four-Way Intercom
Conference 40
6.3.3 Ending Multi-Way Intercom 40
6.4 Three-Way Conference Phone Call
with Intercom Users 41
6.5 Group Intercom 42
6.6 Universal Intercom 43
6.7 Advanced Noise Control™
(Default: Enable) 45
TABLE OF CONTENTS CONTINUED
7. uSING THE fm rADIO 47
7.1 FM Radio On/Off 47
7.2 Seek and Save Radio Stations 47
7.3 Scan and Save Radio Stations 49
7.4 Temporary Station Preset 50
7.5 Navigating Preset Stations 51
7.6 Region Selection
(Default: Worldwide) 52
7.7 Radio Data System (RDS)
Alternative Frequency (AF) Setting
(Default: Enable) 52
8. GENErAL SETTINGS 54
8.1 Function Priority 54
8.2 Firmware Upgrades 54
8.3 Voice Prompts 54
8.4 Delete All Bluetooth Pairing
Information 56
9. rEmOTE CONTrOL 57
9.1 Pairing with the Remote Control 57
10. TrOuBLESHOOTING 59
10.1 Fault Reset 59
10.2 Factory Reset 60
11. mAINTENANCE AND CArE 61
11.1 Outer Shell 61
11.2 Inner Lining 61
11.3 Storing the Helmet 61
1. About the
cAvAlry b luetooth
hAlf helmet
1.1 General Information
MENU
General
Information
Product
Details
Wearing
the Helmet
Pre-Ride
Helmet
Inspection
Accessory
Installation:
Ear Plates
This product is a motorcycle helmet.
Do not use it for any other purpose than riding a
motorcycle. If you use the helmet for anything else,
it may not provide sufficient protection in an
accident.
No helmet can protect the wearer against all
possible impact scenarios.
For maximum protection, the Sena Cavalry
Bluetooth Half Helmet must fit properly on the head
and its retention strap securely fastened under the
chin. With the retention system comfortably but
firmly adjusted, the helmet should allow sufficient
peripheral vision when secured. If the helmet is too
large, it may move on your head while riding. If the
helmet can be moved when pulled from the back
Accessory
Installation:
Ear Pads
in an upward and forward direction, it’s not fitted
properly. This could cause the helmet to obstruct
your vision while riding or come off in an accident,
resulting in personal injury or death. Please refer
to Section 1.3: “Wearing the Helmet” for more
details about properly securing and wearing your
helmet.
The contents of this Sena Calvary Bluetooth Half
Helmet User’s Guide are subject to change without
notice. Its illustrations may differ from the actual
product. The copyrights for the User’s Guide belong
to Sena Technologies, Inc. Reproduction or copying
of the User’s Guide without permission is strictly
prohibited.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 6
General
DC Power Charging &
Bluetooth
Microphone
MENU
1. About the
cAvAlry b luetooth
hAlf helmet
1.2 Product Details
Information
Product
Details
Wearing
the Helmet
Pre-Ride
Helmet
Inspection
Accessory
Installation:
Ear Plates
Communication
Module
Chinstrap
Retention
D-Ring
Firmware Upgrade Port
Accessory
Installation:
Ear Pads
Speakers
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 7
1. About the
cAvAlry b luetooth
hAlf helmet
1.3 Wearing the Helmet
MENU
General
Information
Product
Details
Wearing
the Helmet
Pre-Ride
Helmet
Inspection
Accessory
1.3.1 Putting on the Helmet
1. Unfasten the chinstrap.
2. Gently pull the padded V-straps outward
and slide the helmet onto your head.
Note: A “chinstrap” is the nylon webbing
that goes through the D-Rings.
3. Route the chinstrap under your chin, then
thread it through both D-Rings.
4. To fasten securely, thread chinstrap back
through the D-Ring closest to your neck,
and pull.
Installation:
Ear Plates
Accessory
Installation:
Ear Pads
Thread through
the D-Rings
Chinstrap
Note: Check the chinstrap’s position and
tension regularly to ensure proper fit.
1.3.2 Removing the Helmet
1. Loosen the chinstrap by pulling the red tab
attached to the D-Rings.
2. Pull the chinstrap out from within the
D-Rings.
3. Gently pull the padded V-straps outward
and slide the helmet off your head.
Advice: Fastening the chinstrap after
removing the helmet will help avoid
scratching surfaces it’s placed upon.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 8
1. About the
cAvAlry b luetooth
hAlf helmet
1.4 Pre-Ride Helmet Inspection
MENU
General
Information
Product
Details
Wearing
the Helmet
Pre-Ride
Helmet
Inspection
Accessory
1.4.1 Checking the Exterior
Check the helmet regularly for damage.
Small, superficial scratches will not impair the
helmet’s protective qualities. In the case of
more serious damage (cracks, dents, flaking
and cracking paint, etc.), the helmet should no
longer be used.
Exterior Shell
Removable Visor
Installation:
Ear Plates
Accessory
Installation:
Ear Pads
Chinstrap
1.4.2 Checking the Chinstrap
1. Ensure that the chinstrap is properly routed
under your chin.
2. To test chinstrap tension, slip your index
finger under the chinstrap and pull. If the
chinstrap is loose under the chin, it needs to
be tightened. If the chinstrap loosens when
you pull on it, the helmet is not properly
fitted. Undo the chinstrap completely and
try fastening it again, then repeat the test.
3. If you are unable to fasten the chinstrap so
that it fits firmly against the chin, check that
your helmet is still the right size for you.
Note: Repeat the test after each
adjustment.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 9
General
Information
Product
Details
MENU
1. About the
cAvAlry b luetooth
hAlf helmet
Caution: Never ride with the chinstrap
unfastened or incorrectly adjusted. The
chinstrap should fit correctly and should not
become loose when pulled. The fastener
is not correctly closed if the chinstrap
becomes loose when pulled.
Wearing
the Helmet
Pre-Ride
Helmet
Inspection
Accessory
Installation:
Ear Plates
Accessory
Installation:
Ear Pads
1.5 Accessory Installation: Ear Plates
To amplify the sound from the speakers, you
can use the ear plates. Slide in the included
ear plates on both sides of the helmet. Make
sure they are aligned with your ears.
Ear Plates
Slide ear plates into slots
on both sides of the helmet
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 10
1. About the
cAvAlry b luetooth
hAlf helmet
1.6 Accessory Installation: Ear Pads
MENU
General
Information
Product
Details
Wearing
the Helmet
Pre-Ride
Helmet
Inspection
Accessory
To amplify the sound from the speakers and
cut wind noise in high speeds, you can use the
ear pads. Slide in the left and right ear pads
on corresponding sides of the helmet. Then
slide in each side of the chinstrap through the
bands on the ear pads.
Ear Pads
Installation:
Ear Plates
Accessory
Installation:
Ear Pads
Slide ear pads into slots on
both sides of the helmet
Slide in the chinstrap
through the ear pad’s band
Note: It is recommended that you install
the ear pads at all times to enhance the
sound quality of the helmet.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 11
Button
Enter Voice Confi guration Settings
(-) Button
FM Tuner On/Off
Powering On
MENU
2. GettinG started:
built-in bluetooth
system
2.1 Button Functions
Functions
Powering
On and Off
Charging
Checking the
Bluetooth
Battery
Level
Volume
Adjustment
Downloadable
(+) Button
Increase Volume
Track Forward
Scan Radio Stations
Speed Dial
Fault Reset Button
Blue & Red LED Lights
Decrease Volume
Track Back
Center Button
Answer/End Phone Call
Reject an Incoming Phone Call
Start/End Intercom Conversation
Play/Pause Music
Enter Intercom Pairing Mode
Sena Software
Configuration
Menu
2.2 Powering On and Off
Press and hold the Center Button and the
(+) Button at the same time for 1 second to
turn the headset on or off.
=
POWER ON
DEVICE
HOLD
1s
Powering Off
=
POWER OFF
DEVICE
HOLD
1s
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 12
2. GettinG started:
Charging the Bluetooth Communication Module
DC Power
Charging &
Firmware
built-in bluetooth
system
2.3 Charging
MENU
Button
Functions
Powering
On and Off
Charging
Checking the
Bluetooth
Battery
Level
Volume
The Bluetooth Communication Module can be
charged using many common methods via the
supplied USB power & data cable:
1. Plugged into a computer’s USB port
2. With a USB-equipped AC adapter via
a wall-outlet charger
Note: Please make sure to take off your helmet
while charging. The headset automatically turns
off during charging.
Adjustment
Downloadable
Sena Software
Configuration
Menu
Upgrade Port
Depending upon the charging method, the
Bluetooth Module will be fully charged in about
2.5 hours.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 13
MENU
Battery Level — Visual Method
2. GettinG started:
built-in bluetooth
system
2.4 Checking the Bluetooth Module’s
Button
Functions
Powering
On and Off
Charging
Checking the
Bluetooth
Battery
Level
Volume
Battery Level
There are two ways to check battery level:
1. Visually, with LEDs when powering on.
=
VISUAL
METHOD
=
HOLD
1s
Adjustment
Downloadable
Sena Software
Configuration
MEDIUM
Menu
Note: Blinking LEDs alternate from blue to red
HIGH
=
=
LOW
when battery power is low.
2. Audible method: Press and hold the Center Button and the (+) Button for 3 more seconds
as the headset powers on. A prompt will
announce the remaining battery level.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 14
Button
Battery Level — Visual Method
Battery Level — Audible Method
=
=
=
=
VISUAL
METHOD
HIGH
MEDIUM
LOW
1s
HOLD
Volume Up
MENU
2. GettinG started:
built-in bluetooth
system
Functions
Powering
On and Off
AUDIBLE
METHOD
Charging
Checking the
Bluetooth
Battery
Level
Volume
2.5 Volume Adjustment
You can raise or lower the volume by tapping the
(+) Button or the (-) Button. Volume is set and
Adjustment
maintained independently at different levels for
=
HOLD
3s
“Battery level
(high/medium/low)”
Downloadable
Sena Software
Configuration
Menu
each audio source (i.e., phone, intercom), even
when the headset is rebooted.
TAP
=
VOLUME UP
Volume Down
=
1x
TAP
1x
VOLUME
DOWN
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 15
2. GettinG started:
built-in bluetooth
system
2.6 Downloadable Sena Software
MENU
Button
Functions
Powering
On and Off
Charging
Checking the
Bluetooth
Battery
Level
Volume
Adjustment
2.6.1 Sena Device Manager
The Sena Device Manager allows you to
upgrade the Bluetooth Communication Module’s firmware and configure its settings
directly from your PC or Apple computer.
Using this software, you can assign speed dial
presets, FM radio station presets and more.
For more information on downloading the
Sena Device Manager, please visit sena.com.
Click Here to Visit Sena.com
2.6.2 Sena Smartphone App
Downloadable
Sena Software
Configuration
Menu
The Sena Smartphone App allows you to
configure the Bluetooth Communication Module’s settings, as well as access the User’s
and Quick Start Guides. To do so, pair your
mobile phone with your Cavalry Bluetooth
Half Helmet (please refer to Section 3:
“Pairing the Helmet with other Bluetooth
Devices” for more details). Run the Sena
Smartphone App and configure the settings
directly from your smartphone. You can
download the Sena Smartphone App for
Android and Apple operating systems.
2.7 Configuration Menu
The Bluetooth Communication Module can be
configured by following a series of voice prompts.
Further details about each of these settings will be
explained on the following pages.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 16
2. GettinG started:
Accessing the Confi guration Menu
Accessing the Confi guration Menu
Navigating Forward through the Menu
=
ACCESS
CONFIG.
MENU
10s
HOLD
built-in bluetooth
system
1. To access the Configuration Menu, press and
MENU
Button
Functions
hold the Center Button for 10 seconds until you
hear the voice prompt, “Configuration menu.”
Powering
On and Off
Charging
ACCESS
Checking the
CONFIG.
MENU
Bluetooth
Battery
Level
Volume
2. Tap the (+) Button or the (-) Button to navigate
between the menus. You will hear voice prompts
for each menu item. The list of functions is shown
=
HOLD
10s
Adjustment
in the Configuration Menu Chart on page 19.
Downloadable
Sena Software
Configuration
Menu
NAVIGATE
FORWARD
Navigating Backward through the Menu
=
“(Menu Prompt)”
TAP
1x
NAVIGATE
BACKWARD
TAP
=
“(Menu Prompt)”
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 17
1x
MENU
1x
TAP
1x
TAP
Accessing the Confi guration Menu
Navigating Forward through the Menu
Navigating Backward through the Menu
NAVIGATE FORWARD
NAVIGATE
BACKWARD
=
=
=
ACCESS
CONFIG.
MENU
“(Menu Prompt)”
“(Menu Prompt)”
10s
HOLD
2. GettinG started:
built-in bluetooth
system
3. You can enable/disable the feature or execute the
Button
Functions
Powering
command by tapping the Center Button.
Enable/Disable or Execute a Feature
On and Off
Charging
ENABLE OR
DISABLE
Checking the
Bluetooth
Battery
Level
EXECUTE
=
TAP
1x
Volume
Adjustment
Downloadable
Sena Software
Configuration
Menu
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 18
2. GettinG started:
built-in bluetooth
system
Configuration Menu Chart
MENU
Button
Functions
Powering
On and Off
Charging
Checking the
Bluetooth
Battery
Level
Volume
Tap the (+) Button or (-) Button
the specified number of times
TAP
1x
TAP
2x
TAP
3x
TAP
4x
TAP
5x
Phone PairingExecute
Second Mobile Phone PairingExecute
Phone Selective PairingExecute
Media Selective PairingExecute
Speed DialExecute
Tap the
Center Button
Adjustment
Downloadable
Sena Software
Configuration
Menu
TAP
6x
TAP
7x
TAP
8x
TAP
6x
TAP
5x
TAP
4x
Audio BoostEnable/Disable
Voice Prompt Enable/Disable
RDS AF SettingEnable/Disable
Advanced Noise ControlEnable/Disable
Delete All PairingsExecute
Remote Control Pairing Execute
TAP
3x
TAP
2x
TAP
1x
Universal Intercom PairingExecute
Factory ResetExecute
Exit ConfigurationExecute
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 19
3. PAIRING THE
Also pairs with:
Pairs with up to three Sena Headsets
Bluetooth
Communication Module
MENU
HELMET WITH
OTHER BLUETOOTH
DEVICES
Before using Cavalry’s Bluetooth system with other
Mobile
Phone
Additional
Mobile
Phones, GPS,
MP3 Player
or Sena
SR10 Two-
Way Radio
Adapter
Advanced
Bluetooth devices for the first time, they’ll need to
be “paired.” This enables them to recognize and
communicate with one another whenever they’re
within range.
The helmet’s Bluetooth Module can pair with multiple
Bluetooth devices such as a mobile phone, GPS,
MP3 player or Sena SR10 Two-Way Radio Adapter via
Mobile Phone Pairing and Second Mobile Phone
Pairing. The Bluetooth Helmet module can also be
paired with up to three other Sena headsets.
Selective
Pairing:
Hands-Free
or A2DP
Stereo
Mobile
Phone
MP3
Player
GPS
Devices
Sena
SR10
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 20
3. PAIRING THE
Access Phone Pairing in the Confi guration Menu
LED STATUS
1x
TAP
Access Phone Pairing in the Confi guration Menu
Alternating blue and red flashing lights indicate
device is now discoverable.
NAVIGATE FORWARD
1X
=
=
=
ACCESS
CONFIG.
MENU
LED STATUS
PIN NUMBER
“Phone pairing”
“Confi guration menu”
10s
HOLD
HELMET WITH
OTHER BLUETOOTH
DEVICES
3.1 Mobile Phone
MENU
Mobile
Phone
1. Execute Phone Pairing in the Configuration
Menu.
Additional
Mobile
Phones, GPS,
MP3 Player
=
or Sena
SR10 Two-
Way Radio
ACCESS
CONFIG.
MENU
Adapter
Advanced
“Confi guration menu”
Selective
HOLD
10s
Pairing:
Hands-Free
or A2DP
Stereo
=
NAVIGATE
FORWARD
1X
Alternating blue and red
=
fl ashing lights indicate
device is now discoverable.
TAP
1x
“Phone pairing”
2. With your mobile phone in Bluetooth-pairing
mode, select Sena Cavalry in the list of devices
detected.
3. If your mobile phone asks for a PIN, enter 0000.
=
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 21
3. PAIRING THE
Access Second Mobile Phone
MENU
HELMET WITH
OTHER BLUETOOTH
DEVICES
3.2 Additional Mobile Phones, GPS, MP3
Mobile
Phone
Additional
Mobile
Phones, GPS,
MP3 Player
or Sena
SR10 Two-
Way Radio
Adapter
Advanced
Selective
Player or Sena SR10 Two-Way Radio
Adapter
1. Execute Second Mobile Phone Pairing in the
Configuration Menu.
Pairing in the Confi guration Menu
HOLD
=
ACCESS
CONFIG.
MENU
10s
Pairing:
Hands-Free
or A2DP
Stereo
NAVIGATE
FORWARD
2X
=
“Confi guration menu”
TAP
2x
“Second mobile phone pairing”
Blue fl ashing lights indicates
=
device is now discoverable.
LED STATUS
2. With your mobile phone in Bluetooth-pairing
mode, select Sena Cavalry in the list of devices
detected.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 22
Mobile
1x
TAP
Access Phone Pairing in the Confi guration Menu
Alternating blue and red flashing lights indicate
device is now discoverable.
NAVIGATE FORWARD
1X
=
=
=
ACCESS
CONFIG.
MENU
LED STATUS
PIN NUMBER
“Phone pairing”
“Confi guration menu”
10s
HOLD
Access Phone Selective Pairing
Phone
Additional
Mobile
Phones, GPS,
3. PAIRING THE
HELMET WITH
OTHER BLUETOOTH
DEVICES
3. If your mobile phone asks for a PIN, enter 0000.
=
MENU
MP3 Player
3.3 Advanced Selective Pairing:
or Sena
Hands-Free or A2DP Stereo
SR10 Two-
Way Radio
Adapter
Advanced
Selective
Pairing:
Hands-Free
or A2DP
Stereo
Phone Pairing allows the Bluetooth Module to establish two Bluetooth profiles: Hands-Free or
A2DP Stereo
. Advanced Selective Pairing allows
the module to separate the profiles to enable
connection with two devices.
3.3.1 Phone Selective Pairing —
Hands-Free Profile
1. Execute Phone Selective Pairing in the
Configuration Menu.
in the Confi guration Menu
=
ACCESS
CONFIG.
MENU
“Confi guration menu”
=
HOLD
10s
TAP
3x
NAVIGATE
FORWARD
3X
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 23
3. PAIRING THE
3x
TAP
Access Phone Selective Pairing in the Confi guration Menu
NAVIGATE FORWARD
3X
=
=
ACCESS
CONFIG.
MENU
LED STATUS
“Confi guration menu”
10s
HOLD
3x
TAP
Access Phone Selective Pairing in the Confi guration Menu
Blue flashing lights indicates
device is now discoverable.
NAVIGATE
FORWARD
3X
=
=
=
ACCESS
CONFIG.
MENU
LED STATUS
PIN NUMBER
“Phone selective pairing”
“Confi guration menu”
10s
HOLD
Access Media Selective Pairing
4X
HELMET WITH
OTHER BLUETOOTH
DEVICES
MENU
Mobile
Phone
Additional
Mobile
Phones, GPS,
MP3 Player
or Sena
SR10 Two-
Way Radio
Adapter
Advanced
Selective
Pairing:
Hands-Free
“Phone selective pairing”
Blue fl ashing lights indicates
=
device is now discoverable.
2. With your hands-free device in Bluetoothpairing mode, select Sena Cavalry in the list
of devices detected.
3. If it asks for a PIN, enter 0000.
=
or A2DP
Stereo
3.3.2 Media Selective Pairing —
A2DP Profile
1. Execute Media Selective Pairing in the
Configuration Menu.
in the Confi guration Menu
=
ACCESS
CONFIG.
MENU
HOLD
10s
NAVIGATE
FORWARD
“Confi guration menu”
TAP
=
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 24
4x
3. PAIRING THE
4x
TAP
Access Media Selective Pairing in the Confi guration Menu
NAVIGATE FORWARD
4X
=
=
ACCESS
CONFIG.
MENU
“Confi guration menu”
10s
HOLD
4x
TAP
Access Media Selective Pairing in the Confi guration Menu
Red flashing light indicates
device is now discoverable.
NAVIGATE
FORWARD
4X
=
=
=
ACCESS
CONFIG.
MENU
LED STATUS
“Media selective pairing”
“Confi guration menu”
10s
HOLD
HELMET WITH
OTHER BLUETOOTH
DEVICES
MENU
Mobile
Phone
Additional
Mobile
Phones, GPS,
MP3 Player
or Sena
SR10 Two-
Way Radio
Adapter
Advanced
Selective
“Media selective pairing”
Red fl ashing light indicates
=
device is now discoverable.
LED STATUS
2. With your A2DP device in Bluetooth-pairing
mode, select Sena Cavalry in the list of
devices detected.
3. If it asks for a PIN, enter 0000.
Pairing:
Hands-Free
or A2DP
Stereo
PIN NUMBER
=
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 25
Making and
Answer a Call
Answering
Calls
Speed
MENU
4. Mobile phone usage
4.1 Making and Answering Calls
TAP
=
1x
Dialing
ANSWER
End/Reject a Call
=
END/REJECT
Make a Call with Voice Dialer
=
HOLD
2s
HOLD
3s
VOICE DIAL
Note: If you have a GPS device connected,
you will not hear its voice navigations during a
phone call.
4.2 Speed Dialing
4.2.1 Assigning Speed Dial Presets
1. Execute Speed Dial in the Configuration
Menu by holding down the Center Button
for 10 seconds, then using the (+) and
(-) Buttons to scroll through the menu. Please refer to Section 2.7: “Configuration
Menu” for more details.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 26
Making and
Assigning Speed Dial Presets
5x
TAP
1x
TAP
NAVIGATE FORWARD
5X
=
=
=
ACCESS
CONFIG.
MENU
“Speed dial”
“Confi guration menu”
Assigning Speed Dial Presets
Navigate Forward through Preset Numbers
EXECUTE
10s
HOLD
MENU
4. Mobile phone usage
Answering
Calls
Speed
Dialing
ACCESS
CONFIG.
MENU
NAVIGATE
FORWARD
5X
=
=
HOLD
10s
“Confi guration menu”
TAP
5x
“Speed dial”
=
EXECUTE
TAP
1x
2. Tap the (+) Button or the (-) Button to set
up the three available Speed Dial Presets.
You will hear the voice prompt, “Speed dial” followed by the preset number.
NAVIGATE
FORWARD
1X
TAP
=
1x
“Speed dial (#)”
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 27
5x
TAP
1x
TAP
1x
TAP
NAVIGATE FORWARD
5X
=
=
=
=
ACCESS
CONFIG.
MENU
“Speed dial”
“Confi guration menu”
“Speed dial (#)”
Assigning Speed Dial Presets
Navigate Forward through Preset Numbers
EXECUTE
NAVIGATE
FORWARD
1X
10s
HOLD
5x
TAP
1x
TAP
1x
TAP
1x
TAP
NAVIGATE FORWARD
5X
=
=
=
=
=
ACCESS
CONFIG.
MENU
“Speed dial”
“Confi guration menu”
“Speed dial (#)”
“Speed dial (#)”
Navigate Forward through Preset Numbers
Navigate Backward through Preset Numbers
On Your Mobile Phone, Dial Number
EXECUTE
NAVIGATE
FORWARD
1X
NAVIGATE
BACKWARD
1X
10s
MENU
4. Mobile phone usage
Making and
Answering
Dialing
Calls
Speed
Navigate Backward through Preset Numbers
=
NAVIGATE
BACKWARD
1X
“Speed dial (#)”
TAP
1x
3. On your mobile phone, call the number
to which you want to assign a Speed Dial Preset. The call will be terminated
immediately. Then, you will hear the
voice prompt, “Save speed dial (#).”
This confirms that the number was saved.
MOBILE
PHONE
Dial the phone number
=
on your mobile phone
“Save speed dial (#)”
4. Use this procedure to save other Speed
Dial Presets.
5. To exit the menu, tap the (+) Button or
the (-) Button until you hear the voice
prompt, “Cancel,” then tap the Center Button to confirm.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 28
1x
TAP
1x
TAP
1x
TAP
=
=
=
=
“Speed dial (#)”
“Speed dial (#)”
“Save speed dial (#)”
Navigate Forward through Preset Numbers
Navigate Backward through Preset Numbers
On Your Mobile Phone, Dial Number
Exit Menu
Dial the phone number on your mobile phone
EXECUTE
NAVIGATE
FORWARD
1X
NAVIGATE
BACKWARD
1X
MOBILE
PHONE
Enter Speed Dial Mode
4. Mobile phone usage
Making and
MENU
Answering
Speed
Calls
EXIT
MENU
Dialing
CONFIRM
CANCEL
=
“Cancel”
=
TAP
1x
TAP
1x
4.2.2 Using Speed Dial Presets
1. Press and hold the (+) Button for 3 seconds
to enter into the Speed Dial menu. You will
hear the voice prompt, “Speed dial.”
HOLD
=
SPEED DIAL
“Speed dial”
3s
2. Tap the (+) Button or the (-) Button to
navigate between the Speed Dial Presets.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 29
Enter Speed Dial Mode
SPEED DIAL
=
“Speed dial”
3s
HOLD
1x
TAP
1x
TAP
1x
TAP
“Speed dial (#)”
Enter Speed Dial Mode
Navigate Forward through Speed Dial Preset Numbers
Navigate Backward through Speed Dial Preset Numbers
Call a Speed Dial Preset Number
NAVIGATE
FORWARD
SPEED DIAL
NAVIGATE
BACKWARD
SPEED DIAL
REDIAL
=
=
=
=
“Speed dial”
3s
HOLD
Making and
MENU
4. Mobile phone usage
Navigate Forward through Speed Dial Preset Numbers
Answering
=
Calls
Speed
NAVIGATE
FORWARD
Dialing
Navigate Backward through Speed Dial Preset Numbers
=
NAVIGATE
BACKWARD
3. To redial the last number called, tap the
Center Button when you hear the prompt,
TAP
1x
TAP
1x
“Last number redial.”
Redial Last Number
“Last number redial”
=
4. To call one of your Speed Dial Presets,
TAP
1x
tap the Center Button when you hear the
prompt, “Speed dial (#).”
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 30
Making and
1x
TAP
1x
TAP
Enter Speed Dial Mode
Navigate Forward through Speed Dial Preset Numbers
Navigate Backward through Speed Dial Preset Numbers
NAVIGATE
FORWARD
SPEED DIAL
NAVIGATE
BACKWARD
=
=
=
“Speed dial”
3s
HOLD
Answering
Calls
Speed
MENU
4. Mobile phone usage
Call a Speed Dial Preset Number
“Speed dial (#)”
Dialing
SPEED DIAL
=
TAP
1x
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 31
MENU
Play/Pause Music
Volume Up
5. Stereo muSic
5.1 Playing Music with Bluetooth Devices
Playing
Music with
Bluetooth
Devices
Music
Sharing
Audio Boost
1. To play or pause music, press and hold the
Center Button for 1 second until you hear a
double beep.
=
PLAY/PAUSE
“[Beep, Beep]”
HOLD
1s
2. To adjust the volume, tap the (+) Button or the
(-) Button.
TAP
=
VOLUME UP
Volume Down
=
1x
TAP
1x
VOLUME
DOWN
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 32
5. Stereo muSic
Play/Pause Music
=
PLAY/PAUSE
“[Beep, Beep]”
1s
HOLD
Sharing Music with an Intercom Friend
3. To track forward or back, press and hold the
MENU
Playing
Music with
Bluetooth
Devices
Music
Sharing
Audio Boost
(+) Button or the (-) Button for 1 second.
Next Track
=
SKIP TRACK
FORWARD
Previous Track
=
HOLD
1s
HOLD
1s
SKIP TRACK
BACKWARD
5.2 Music Sharing
You can share the music you’re listening to with an
Intercom Friend during an intercom conversation.
To start or terminate sharing music, press the
Center Button for 1 second during an intercom
conversation until you hear a double beep. Both
you and your Intercom Friend can control music
playback.
during Intercom Conversation
SHARE
MUSIC
HOLD
=
“[Beep, Beep]”
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 33
1s
5. Stereo muSic
Accessing Audio Boost in the Confi guration Menu
5.3 Audio Boost (Default: Enable)
MENU
Playing
Music with
Bluetooth
Devices
Music
Sharing
Audio Boost
An Audio Boost setting can be found in the
Configuration Menu. Enabling Audio Boost
increases the maximum volume limit. Disabling
Audio Boost reduces the maximum volume limit
while delivering more balanced sound.
HOLD
=
ACCESS
CONFIG.
MENU
10s
“Confi guration menu”
=
NAVIGATE
FORWARD
6X
“Audio boost”
TAP
6x
ENABLE OR
DISABLE
TAP
=
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 34
1x
1x
TAP
LED STATUS
On Either One of the Devices
Pairing with Intercom Friends
Blue flashing LED confirms
intercoms are paired.
YOU
INTERCOM
FRIEND B
B
A
or
YOU
INTERCOM
FRIEND B
B
A
&
=
=
=
“Intercom pairing”
5s
HOLD
Red flashing light indicates
device is now discoverable.
=
LED STATUS
Pairing with Intercom B
MENU
Multi-Way
Three-Way
Conference
Intercom
Pairing
Two-Way
Intercom
Intercom
6. INTERCOM SETUP
6.1 Intercom Pairing
Up to three people can communicate via intercom
with the Cavalry Bluetooth Helmet simply by pairing
their headsets.
A
CB
D
Phone
Call with
Intercom
Users
1. Press and hold the Center Buttons of two
Group
Intercom
Universal
Intercom
Advanced
Noise
Control™
Bluetooth Modules for 5 seconds until you hear
the voice prompt, “Intercom pairing.”
A
YOU
HOLD
&
=
5s
INTERCOM
B
FRIEND B
“Intercom pairing”
Red fl ashing light indicates
=
device is now discoverable.
LED STATUS
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 35
6. INTERCOM SETUP
Pairing with Intercom B
On Either One of the Devices
YOU
INTERCOM
FRIEND B
B
A
&
=
“Intercom pairing”
5s
HOLD
Red flashing light indicates
device is now discoverable.
=
LED STATUS
MENU
Intercom
Pairing
Two-Way
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
2. Tap the Center Button on either Bluetooth
Module and wait until the LEDs of both turn blue.
A
YOU
or
B
=
1x
TAP
Call with
Intercom
INTERCOM
Users
Group
Intercom
Universal
LED STATUS
Intercom
Advanced
Noise
Control™
3. Repeat steps 1 and 2 to pair with Intercom
Intercom Friends
FRIEND B
Blue fl ashing LED confi rms
=
intercoms are paired.
Friends C & D.
Additional paired headsets are set up as
Intercom Friends. The intercom pairing order is
“Last-Come, First-Served.” To distinguish between
multiple headsets paired to the Cavalry Bluetooth
Half Helmet for intercom use, Sena designates
the headset paired last as Intercom Friend 1. The
previous intercom set up is designated Intercom
Friend 2; the headset paired prior to Intercom
Friend 2 becomes Intercom Friend 3.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 36
Intercom
Last-Come, First-Served
Friend 1
Friend 2
Friend 3
Start/End Two-Way Intercom with Intercom Friend 1
MENU
6. INTERCOM SETUP
Pairing
Two-Way
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
Call with
Intercom
Users
A
YOU
A
YOU
AD
B
Intercom
Friend 1
C
Intercom
Friend 1
B
Intercom
Friend 2
C
B
Group
Intercom
Universal
Intercom
Advanced
Noise
Control™
YOUIntercom
Intercom
Intercom
6.2 Two-Way Intercom
You can start or end an intercom conversation with
an Intercom Friend by tapping the Center Button.
1. Tap once for Intercom Friend 1.
D
=
1x
TAP
INTERCOM
FRIEND 1
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 37
Intercom
1x
TAP
D
Start/End Two-Way Intercom with Intercom Friend 1
Start/End Two-Way Intercom with Intercom Friend 2
=
INTERCOM
FRIEND 1
2x
TAP
1x
TAP
D
C
Start/End Two-Way Intercom with Intercom Friend 1
Start/End Two-Way Intercom with Intercom Friend 2
Start/End Two-Way Intercom with Intercom Friend 3
=
=
INTERCOM
FRIEND 1
INTERCOM
FRIEND 2
Pairing
MENU
6. INTERCOM SETUP
2. Tap twice for Intercom Friend 2.
Two-Way
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
Call with
Intercom
Users
Group
C
=
INTERCOM
FRIEND 2
3. Tap three times for Intercom Friend 3.
B
=
INTERCOM
FRIEND 3
TAP
2x
TAP
3x
Intercom
6.3 Multi-Way Intercom
Universal
Intercom
Advanced
Noise
Control™
Multi-Way Intercom enables conference-call-style
conversations with up to three Intercom Friends
at the same time. While Multi-Way Intercom is in
progress, mobile phone connection is temporarily
disconnected. However, as soon as Multi-Way Intercom terminates, the mobile phone connection
will be reestablished.
6.3.1 Starting a Three-Way Intercom
Conference
You (A) can have a Three-Way Intercom
Conference with two other Intercom
Friends (B & C) by establishing two intercom
connections simultaneously.
1. Pair your headset (A) with those of two
other Intercom Friends (B & C). Please
refer to Section 6.1: “Intercom Pairing” for
pairing instructions.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 38
6. INTERCOM SETUP
Pair with Intercom Friends B & C
Starting an Intercom Conversation
Pair with Intercom Friends B & C
CB
A
You
Intercom
Friend B
Intercom
Friend C
Starting an Intercom Conversation with Intercom Friend B
Pair with Intercom Friends B & C
CB
A
You
Intercom
Friend B
Intercom
Friend C
C
B
A
You
Friend B
Intercom
Friend B
Friend C
Intercom
Friend C
MENU
Intercom
Pairing
Two-Way
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
Call with
Intercom
A
CB
You
Intercom
Friend B
Intercom
Friend C
2. Start an intercom conversation with one of
the two friends in your intercom group. For
example, you (A) may start an intercom
conversation with the Intercom Friend (B). Or, Intercom Friend (B) may start an
intercom call with you (A).
Users
Group
Intercom
Universal
Intercom
Advanced
Control™
Noise
with Intercom Friend B
A
B
Intercom
Friend B
You
Intercom
Friend C
C
3. Then, you (A) can call the second Intercom
Friend (C), or the second Intercom Friend
(C) may join the intercom by making an intercom call to you (A).
Starting an Intercom Conversation
with Intercom Friend C
A
B
You
Intercom
C
Intercom
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 39
6. INTERCOM SETUP
Starting an Intercom Conversation with Intercom Friend B
Starting an Intercom Conversation with Intercom Friend C
Pair with Intercom Friends B & C
CB
A
You
Intercom
Friend B
Intercom
Friend C
Three-Way Conference
C
C
B
B
A
A
You
You
Friend B
Intercom
Friend B
Intercom
Friend B
Friend C
Intercom
Friend C
Intercom
Friend C
Starting a Four-Way Intercom
4. Now you (A) and two Intercom Friends
MENU
Intercom
Pairing
Two-Way
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
Call with
Intercom
(B & C) are having a Three-Way Intercom
Conference.
A
B
You
Intercom
6.3.2 Starting a Four-Way Intercom
Conference
C
Intercom
Users
Group
Intercom
Universal
Intercom
Advanced
Noise
Control™
With three Intercom Friends connected, a
new participant (D) can make it a Four-Way Intercom Conference by making an intercom
call to either (B) or (C).
B
Intercom
Friend B
YOU
A
Intercom
Friend C
C
D
Intercom
Friend D
6.3.3 Ending Multi-Way Intercom
1. Press the Center Button for 1 second
until you hear a beep to terminate all
intercom connections.
2. Tap the Center Button to disconnect from
your first Intercom Friend. Double tap the
Center Button to disconnect from your
second Intercom Friend.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 40
MENU
Invite an Intercom Friend into Phone Conference
1x
TAP
Invite an Intercom Friend into Phone Conference
ADD AN
INTERCOM
FRIEND
TO CALL
DISCONNECT
=
1x
TAP
1x
TAP
Invite an Intercom Friend into Phone Conference
Disconnect Intercom Friend from Conference
ADD AN
INTERCOM
FRIEND
TO CALL
DISCONNECT
INTERCOM
CALL
=
=
6. INTERCOM SETUP
6.4 Three-Way Conference Phone Call
Intercom
Pairing
Two-Way
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
Call with
Intercom
Users
with Intercom Users
You can have a Three-Way Conference Phone Call
by adding an Intercom Friend to the mobile phone
conversation.
1. During a mobile phone call, tap the Center Button to invite one of your Intercom Friends
to the conversation.
TAP
=
ADD AN
INTERCOM
FRIEND
TO CALL
1x
Group
Intercom
Universal
2. To disconnect the intercom during a conference
phone call, tap the Center Button.
Disconnect Intercom Friend from Conference
Intercom
Advanced
=
Noise
Control™
INTERCOM
3. To disconnect the mobile phone call during a
conference phone call, press the Center Button
for 2 seconds.
End Phone Call
TAP
1x
=
END
MOBILE
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 41
HOLD
2s
Intercom
Start Group Intercom
Pairing
Two-Way
MENU
6. INTERCOM SETUP
Note: When you have an incoming intercom call
during a mobile phone call, you will hear a voice
prompt, “Intercom requested.”
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
Call with
Intercom
Users
Group
Intercom
6.5 Group Intercom
Group Intercom allows you to instantly create a
Multi-Way Conference Intercom with three of the
most recently paired headsets.
1. Pair intercoms with up to three people you want
in the Group Intercom.
2. Tap the (+) Button and the (-) Button
simultaneously to begin Group Intercom. The
alternating blue and red flashing lights indicates
that the device is now in Group Intercom mode
and you will hear a voice prompt, “Group
intercom.”
Universal
Intercom
Advanced
Noise
Control™
START
GROUP
INTERCOM
LED STATUS
=
=
TAP
1x
Alternating blue and red
fl ashing lights indicate device is
now in Group Intercom mode.
“Group intercom”
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 42
MENU
1x
TAP
Start Group Intercom
START
GROUP
INTERCOM
LED STATUS
=
=
“Group intercom”
Alternating blue and red flashing lights indicate device is
now in Group Intercom mode.
1x
TAP
Start Group Intercom
End Group Intercom
START
GROUP
INTERCOM
LED STATUS
=
=
“Group intercom”
“Group intercom connected”
Alternating blue and red flashing lights indicate device is
now in Group Intercom mode.
6. INTERCOM SETUP
3. When all of the headsets are connected together,
Intercom
Pairing
Two-Way
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
Call with
everyone will hear the voice prompt, “Group
intercom connected.”
“Group intercom connected”
4. To terminate Group Intercom, press the Center
Button for 1 second during Group Intercom.
You will hear a voice prompt, “Group intercom
terminated.”
Intercom
Users
Group
Intercom
Universal
Intercom
Advanced
Noise
Control™
=
END GROUP
INTERCOM
“Group intercom terminated”
6.6 Universal Intercom
Universal Intercom allows you to have intercom
conversations with users of non-Sena Bluetooth
headsets. You can pair the Cavalry Bluetooth
HOLD
1s
Helmet with only one non-Sena headset at a time.
The intercom distance depends on the performance
of the Bluetooth headset to which it’s connected.
When a non-Sena Bluetooth headset is paired with
the Bluetooth Helmet, if another Bluetooth device
is paired via Second Mobile Phone Pairing, it will
be disconnected.
1. Execute Universal Intercom in the Configuration
Menu. Please refer to Section 2.7:
“Configuration Menu” for more details.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 43
Intercom
Access Universal Intercom in the Confi guration Menu
3x
TAP
Access Universal Intercom in the Configuration Menu
NAVIGATE
BACKWARD
3X
=
=
ACCESS
CONFIG.
MENU
“Universal intercom”
“Confi guration menu”
10s
HOLD
Pairing
Two-Way
6. INTERCOM SETUP
=
MENU
HOLD
10s
Intercom
ACCESS
CONFIG.
MENU
Multi-Way
Intercom
“Confi guration menu”
Three-Way
Conference
Phone
Call with
=
Intercom
Users
NAVIGATE
Group
Intercom
BACKWARD
3X
TAP
3x
Universal
“Universal intercom”
Intercom
Advanced
Noise
=
Control™
EXECUTE
2. Put the non-Sena Bluetooth headset in Pairing
Mode. The Cavalry Bluetooth Half Helmet will
automatically pair with a non-Sena Bluetooth
headset.
3. You can have Two-Way Intercom or Multi-
TAP
1x
Way Intercom communication with up to three
Intercom Friends using non-Sena headsets by
following the procedures described below.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 44
Intercom
Example of a Three-Way Universal Intercom
Pairing
Two-Way
MENU
6. INTERCOM SETUP
Intercom
Multi-Way
Intercom
Three-Way
Conference
Phone
Call with
Intercom
Users
Group
Intercom
You
Non-Sena
Headset
Example of a Four-Way Universal Intercom
YouSena
Headset
Non-Sena
Headset
Sena
Headset
Non-Sena
Headset
Universal
6.7 Advanced Noise Control™
Intercom
(Default: Enable)
Advanced
Noise
Control™
An Advanced Noise Control setting can be found
in the Configuration Menu. Please refer to Section
2.7: “Configuration Menu” for more details.
If Advanced Noise Control
noise is reduced during intercom conversations.
If Advanced Noise Control is disabled, the
background noise is mixed with your voice while
using the intercom.
is enabled, background
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 45
6. INTERCOM SETUP
Access Advanced Noise Control
DISABLE
MENU
Intercom
in the Confi guration Menu
Pairing
Two-Way
Intercom
ACCESS
Multi-Way
CONFIG.
MENU
Intercom
Three-Way
Conference
Phone
Call with
Intercom
Users
=
=
HOLD
10s
“Confi guration menu”
TAP
6x
Group
Intercom
Universal
Intercom
Advanced
Noise
Control™
NAVIGATE
BACKWARD
6X
ENABLE OR
=
“Noise control”
TAP
1x
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 46
7. USING THE FM RADIO
FM Radio On
Seek Stations Forward
7.1 FM Radio On/Off
MENU
FM Radio
On/Off
Seek and
Save Radio
Stations
Scan and
Save Radio
Stations
Temporary
Station
Preset
To turn on or shut off the FM radio, press the
(-) Button for 1 second until you hear a double
beep.
HOLD
=
FM RADIO
ON
“[Beep, Beep]”
1s
Navigating
Stations
Region
Selection
Radio Data
System (RDS)
Alternative
Frequency
Preset
(AF)
FM Radio Off
=
FM RADIO
OFF
“[Beep, Beep]”
7.2 Seek and Save Radio Stations
HOLD
1s
The “Seek” feature searches for radio stations.
1. Double tap the (+) Button or the (-) Button to
search for radio stations.
TAP
=
SEEK
FORWARD
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 47
2x
FM Radio
Seek Stations Forward
Seek Stations Backward
SEEK
FORWARD
=
2x
TAP
Seek Stations Forward
Seek Stations Backward
Enter Preset Selection Mode
SEEK
FORWARD
SEEK
BACKWARD
=
=
2x
TAP
2x
TAP
Seek Stations Forward
Seek Stations Backward
Enter Preset Selection Mode
Navigate Forward through Preset Stations
ENTER
PRESET
MODE
SEEK
FORWARD
SEEK
BACKWARD
3s
HOLD
=
=
=
“Preset (#)”
2x
TAP
2x
TAP
On/Off
Seek and
7. USING THE FM RADIO
=
2x
MENU
TAP
Save Radio
Stations
Scan and
Save Radio
Stations
Temporary
Station
Navigating
Preset
Preset
Stations
Region
Selection
SEEK
BACKWARD
2. To save the current station, press and hold the
Center Button for 3 seconds until you hear the
voice prompt, “Preset (#).”
HOLD
ENTER
PRESET
MODE
=
“Preset (#)”
3s
Radio Data
System (RDS)
3. Tap the (+) Button or the (-) Button to navigate
Alternative
Frequency
(AF)
through the preset numbers that you want to
store.
=
NAVIGATE
FORWARD
TAP
1x
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 48
Seek Stations Forward
Seek Stations Backward
Enter Preset Selection Mode
Navigate Forward through Preset Stations
Navigate Backward through Preset Stations
NAVIGATE
FORWARD
ENTER
PRESET
MODE
SEEK
FORWARD
SEEK
BACKWARD
1x
TAP
3s
HOLD
=
=
=
=
“Preset (#)”
2x
TAP
2x
TAP
Seek Stations Backward
Enter Preset Selection Mode
Navigate Forward through Preset Stations
Navigate Backward through Preset Stations
Save Station to the Preset Number
NAVIGATE
BACKWARD
NAVIGATE
FORWARD
ENTER
PRESET
MODE
SEEK
FORWARD
SEEK
BACKWARD
1x
TAP
1x
TAP
3s
HOLD
=
=
=
=
“Preset (#)”
2x
TAP
7. USING THE FM RADIO
FM Radio
On/Off
Seek and
Save Radio
Stations
Scan and
Save Radio
4. Press and hold the (+) Button for 1 second to
MENU
TAP
=
NAVIGATE
BACKWARD
save the station in the preset number you choose.
1x
Stations
Or, press and hold the (-) Button for 1 second to
delete the station from memory.
Temporary
Station
Preset
=
Navigating
Preset
Stations
Region
Selection
Radio Data
System (RDS)
SAVE TO
PRESET #
Delete Station from Memory
=
Alternative
Frequency
(AF)
DELETE
STATION
HOLD
1s
HOLD
1s
7.3 Scan and Save Radio Stations
The “Scan” function automatically searches for
radio stations, starting with the current station’s
frequency, then up from there.
1. Press and hold the (+) Button for 1 second to
scan for stations.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 49
FM Radio
Scan and Save Radio Stations
SCANNING
Scan and Save Radio Stations
START
SCANNING
1s
HOLD
=
“Preset (#)”
Scan and Save Radio Stations
Save the Current Station
START
SCANNING
SAVE
STATION
SCANNING
1x
TAP
1s
HOLD
=
=
On/Off
Seek and
7. USING THE FM RADIO
HOLD
=
MENU
1s
Save Radio
Stations
Scan and
2. The Sena tuner pauses at each station it finds for
Save Radio
Stations
3. To save the current station, tap the Center
Temporary
Station
Preset
Save the Current Station
Navigating
Preset
Stations
Region
Selection
START
8 seconds before moving to the next.
Button. The station will be saved as the next
preset number.
=
SAVE
STATION
“Preset (#)”
TAP
1x
Radio Data
System (RDS)
Alternative
Frequency
(AF)
4. To stop scanning, press the (+) Button for
Stop Scanning
7.4 Temporary Station Preset
1 second.
=
STOP
HOLD
1s
The Temporary Preset feature automatically finds
and saves the nearest 10 radio stations without
changing your existing preset stations.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 50
7. USING THE FM RADIO
Temporary Stations
Navigate through Preset Stations
1. Tap the (+) Button three times to automatically
MENU
FM Radio
On/Off
Seek and
Save Radio
Stations
Scan and
Save Radio
Stations
Temporary
Station
find and save 10 stations.
=
TEMPORARY
STATIONS
2. The temporary preset stations will be cleared
when the Bluetooth Module reboots.
7.5 Navigating Preset Stations
TAP
3x
Preset
Navigating
Preset
Stations
Region
Selection
Radio Data
System (RDS)
Alternative
Frequency
(AF)
Using the methods above, up to 10 radio stations
can be stored. Press and hold the Center Button
for 1 second to navigate through the saved
stations.
HOLD
=
NAVIGATE
FORWARD
Note: You can use the Sena Device Manager or
1s
the Sena Smartphone App to save the preset
stations.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 51
7. USING THE FM RADIO
7.6 Region Selection
MENU
FM Radio
On/Off
Seek and
Save Radio
Stations
Scan and
Save Radio
Stations
Temporary
Station
Preset
(Default: Worldwide)
You can select the proper FM frequency range
for your location from the Sena Device Manager
or the Sena Smartphone App. Using the region
setting, you can optimize the seek function to avoid
unnecessary frequency ranges.
RegionFrequency rangeStep
Worldwide76.0 ~ 108.0 MHz± 100 kHz
North America,
South America
and Australia
87.5 ~ 107.9 MHz± 200 kHz
Navigating
Preset
Stations
Region
Selection
Radio Data
System (RDS)
Alternative
Frequency
(AF)
Asia and Europe87.5 ~ 108.0 MHz± 100 kHz
Japan76.0 ~ 95.0 MHz± 100 kHz
7.7 Radio Data System (RDS)
Alternative Frequency (AF) Setting
(Default: Enable)
The RDS AF setting can be found in the
Configuration Menu. Please refer to Section 2.7:
“Configuration Menu” for more details.
When radio station signals get too weak for good
reception, with RDS AF enabled, the Sena radio
receiver re-tunes to a station with better reception.
If RDS AF is disabled, you’ll have to find stronger
stations manually.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 52
FM Radio
Access RDS AF Setting in the Confi guration Menu
On/Off
Seek and
7. USING THE FM RADIO
HOLD
=
10s
MENU
Save Radio
Stations
ACCESS
CONFIG.
MENU
Scan and
Save Radio
“Confi guration menu”
Stations
Temporary
Station
=
Preset
Navigating
Preset
Stations
NAVIGATE
FORWARD
8X
TAP
8x
Region
Selection
Radio Data
System (RDS)
Alternative
Frequency
(AF)
ENABLE OR
DISABLE
“RDS AF setting”
=
TAP
1x
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 53
8. GENERAL SETTINGS
8.1 Function Priority
MENU
Function
Priority
Firmware
Upgrades
Voice
Prompts
Deleting All
Bluetooth
Pairing
Information
The headset prioritizes connected devices in the
following order:
(highest)Mobile phone
Intercom
Music sharing via Bluetooth stereo
FM radio
(lowest) Bluetooth stereo music
A lower-priority function gets interrupted by a
higher-priority function. For example, stereo music
will be interrupted by an Intercom Conversation;
an Intercom Conversation will be interrupted by an
incoming mobile phone call.
8.2 Firmware Upgrades
The Cavalry Bluetooth Half Helmet supports
firmware upgrades. You can upgrade the firmware
using the Sena Device Manager. Please refer to
Section 2.6.1: “Sena Device Manager” for more
details. Please visit sena.com to check for the latest
software downloads.
Click Here to Visit Sena.com
8.3 Voice Prompts
A Voice prompt setting can be found in the
Configuration Menu. Please refer to Section 2.7:
“Configuration Menu” for more details.
If Voice prompt is enabled, you can hear Voice
prompts for different kinds of features. If Voice
prompt is disabled, Voice prompts are silenced
except for those in the Configuration Menu, battery
level indication, speed dial, and FM radio functions.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 54
Function
Access Voice Prompt in the Confi guration Menu
Priority
Firmware
8. GENERAL SETTINGS
=
MENU
HOLD
10s
Upgrades
ACCESS
CONFIG.
MENU
Voice
Prompts
“Confi guration menu”
Deleting All
Bluetooth
Pairing
Information
=
NAVIGATE
FORWARD
7X
TAP
7x
ENABLE OR
DISABLE
=
“Voice prompt”
TAP
1x
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 55
8. GENERAL SETTINGS
Access Delete All Pairings in the Confi guration Menu
8.4 Delete All Bluetooth Pairing
MENU
Function
Priority
Firmware
Upgrades
Voice
Prompts
Deleting All
Bluetooth
Pairing
Information
Information
A Delete All Bluetooth Pairing Information
setting can be found in the Configuration Menu.
Please refer to Section 2.7: “Configuration Menu”
for more details.
Tap the Center Button when in this menu to
Delete All Bluetooth Pairing Information
stored in the headset.
HOLD
=
10s
ACCESS
CONFIG.
MENU
“Confi guration menu”
=
NAVIGATE
BACKWARD
5X
TAP
5x
EXECUTE
“Delete all pairings”
TAP
=
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 56
1x
MENU
Access Remote Control Pairing
9. REMOTE CONTROL
You can remotely control the Bluetooth Module using
Pairing with
the Remote
Control
Sena Remote Control devices (sold separately) such
as a Handlebar Remote or a Wristband Remote. This
eliminates the need to remove your hands from the
handlebars for button operations.
9.1 Pairing with the Remote Control
1. Turn on the Bluetooth Module and the Remote
Control device.
2. Execute Remote Control Pairing in the
Configuration Menu. Please refer to Section 2.7:
“Configuration Menu” for more details.
in the Confi guration Menu
ACCESS
CONFIG.
MENU
=
=
HOLD
10s
“Confi guration menu”
TAP
4x
NAVIGATE
BACKWARD
4X
EXECUTE
“Remote control pairing”
TAP
=
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 57
1x
9. REMOTE CONTROL
4x
TAP
1x
TAP
Access Remote Control Pairing in the Confi guration Menu
EXECUTE
NAVIGATE
BACKWARD
4X
=
=
=
ACCESS
CONFIG.
MENU
“Remote control pairing”
“Confi guration menu”
10s
HOLD
3. Enter pairing mode in the Remote Control
MENU
Pairing with
the Remote
Control
device. The Bluetooth Module will automatically
connect with the Remote Control device in
pairing mode. You will hear a voice prompt,
“Remote control connected,” when they are
successfully paired.
Enter Pairing Mode
REMOTE
CONTROL
=
Enter Pairing Mode
on Remote Control.
“Remote control connected”
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 58
MENU
Fault Reset
10. TroubleshooTing
Please visit sena.com for answers to frequently asked
Fault Reset
Factory
Reset
questions. This detailed online FAQ section deals
with troubleshooting, illustrates case studies and
contains tips on using the Sena Cavalry Bluetooth
Half Helmet.
Click Here to Visit Sena.com
10.1 Fault Reset
When the helmet’s Bluetooth Module is not working
properly, you can easily reset the unit:
1. Locate the pinhole reset button below the
(+) Button.
2. Gently insert a paper clip into the hole and
press the Fault Reset Button for 1 second
with light pressure.
HOLD
=
FAULT RESET
3. The communication module will shut down.
1s
Note: Fault Reset will not restore the Bluetooth
Module to factory default settings.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 59
10. TroubleshooTing
Access Factory Reset in the Confi guration Menu
10.2 Factory Reset
MENU
Fault Reset
Factory
Reset
To erase all of your settings and start fresh,
the headset can be restored to factory default
settings using the Factory Reset feature in the
Configuration Menu. Please refer to Section 2.7:
“Configuration Menu” for more details.
HOLD
=
ACCESS
CONFIG.
MENU
10s
“Confi guration menu”
=
NAVIGATE
BACKWARD
2X
=
TAP
2x
“Factory reset”
TAP
1x
EXECUTE
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 60
11. Maintenance
and care
11.1 Outer Shell
MENU
Outer Shell
Inner Lining
Storing the
Helmet
Use a soft cloth and a small amount of water to
remove bugs from the exterior.
Note: Never use gasoline, diesel fuel, thinners or
solvents to clean the helmet. These substances
can cause serious damage to the helmet, even
though the resulting damage may not be visible.
The full safety function of the helmet can then no
longer be guaranteed.
11.2 Inner Lining
The inner lining of the Sena Cavalry Bluetooth Half
Helmet is completely removable. Its headliner can
be washed by hand using mild soap at a maximum
temperature of 30ºC (86ºF). Allow the lining to dry
at room temperature.
11.3 Storing the Helmet
Store the helmet in a dry, dark, well-ventilated
location, out of the reach of children and animals.
Always position the helmet so that it cannot fall
to the floor. Damage that occurs in this way is not
covered by the warranty.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 61
Sena Technologies, Inc. reserves the right to make
any changes and improvements to its product
without providing prior notice.
Sena™ is a trademark of Sena Technologies,
Inc. or its subsidiaries in the USA and other
countries. Cavalry™, FreeWire™, Tufftalk™,
10S™, 10R™, 10U™, 10C™, Prism™, 20S™,
Snowtalk™, 3S™, SMH10™, SMH5™, SMH5-FM™,
SPH10™, SPH10H™, SPH10H-FM™, SMH10R™,
SPH10S™, SR10™, SR10i™, SM10™, EXPAND™,
Bluetooth Pack for GoPro
®
are trademarks of
Sena Technologies, Inc. or its subsidiaries. These
trademarks may not be used without the express
permission of Sena.
GoPro
®
is a registered trademark of Woodman
Labs of San Mateo, California. Sena Technologies,
Inc. (“Sena”) is not affiliated with Woodman Labs,
Inc. The Sena Bluetooth Pack for GoPro
®
is an
aftermarket accessory specially designed and
manufactured by Sena Technologies, Inc. for the
GoPro
®
Hero3 and Hero4 allowing for Bluetooth
Version 1.0.0
capabilities.
The Bluetooth
®
word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks by
Sena is under license. iPhone
®
and iPod® touch are
registered trademarks of Apple Inc.
Sena Cavalry Bluetooth® Half Helmet Firmware v1.0 | 62
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.