PREPARATION
1
2
1
3
2
1
2
1
2
Knowing the Headset Layout
Headset
Status LED
Charging LED
DC Power Charging &
Firmware Upgrade Port
Clamp Unit
Jog Dial
Phone Button
MP3 Port
Microphone
Connector
Installing the Headset
Clamp Unit
Headset
Speaker
Left
Right
Microphone
1
2
BASIC OPERATION
Operating the Buttons
5
Tap the
button
Turning On/O the Headset
Simultaneously press and hold the Jog Dial and the Phone Button
for 1 second to turn on or o the headset.
Adjusting the Volume
Double tap the
button
Press and hold
the button for
5 seconds
ON
1
OFF
Press the two
buttons at the
same time
You will hear ascending
beeps.
“Hello”
You will hear descending
beeps.
“Good bye”
Rotate the
Jog Dial
Checking the Battery Level
Blinking
Blinking
Blinking
Turn on the headset and check the battery level via the Status LED.
“High” 70~100%
3
Or, press and hold the Jog Dial and the Phone Button for 3 more
seconds when the headset turns on. You will hear a triple beep
and a voice prompt.
“Medium” 30~70%
“Low” 0~30%
70~100%
30~70%
0~30%
Charging the Battery
Charging
Fully charged
or
PAIRING
Pairing with Mobile Devices - Phone, Music
“Phone pairing”
Bluetooth
Bluetooth
Sena10S
“Your headset is paired”
Using Phone Features
After Pairing…
Answering Calls
or
Ending Calls Rejecting Calls
or
“Hello”
or
until you hear a beep until you hear a beep
Making Calls
Using the Phone Keypad Using the Voice Dialer
Left Speaker
Earbud Port
Connector
Right Speaker
Connector
You will hear a beep when the volume
reaches the maximum or minimum
level.
AC adapter
Using the Speed Dial
You will hear a beep.
“Speed dial”
Voice Menu
• Last number redial
• Speed dial 1
• Speed dial 2
• Speed dial 3
• Cancel
Listening to Music
After Pairing…
Playing or Pausing Music Tracking Forward or Backward
until you hear
a double beep
1
Rotate While
Pressing
INTERCOM
Pairing with Other Headsets
Headset A Headset B
“Intercom pairing”
Follow the steps above to pair with two or more headsets.
Using the Intercom
After Pairing…
1
RADIO
Turning On/O the FM Radio
1
Seeking Stations
Rotate While Pressing
Saving or Deleting Stations
To Save To Delete
You will hear a double beep sound.
“FM on” or “FM o”
Listening to Preset
Stations
SETTING
Method1) Using the headset
You will hear a double beep sound.
“Conguration menu”
Method2) Using the Sena Device Manager
Connect the headset to your computer via a USB cable. Launch the Sena
Device Manager and click DEVICE SETTING to congure the headset
settings.
For details about downloading the Sena Device Manager, refer to the
leaet included in the package.
Method3) Using the Sena Smartphone App
1. On your smartphone, download the Sena Smartphone App for Android
or iPhone from Google Play or App Store.
Refer to www.sena.com/headset-app/ for more details.
2. Pair your smartphone with the headset.
TROUBLESHOOTING
Factory Reset
If you want to restore the 10S to factory default settings, press and hold the
Phone Button for 10 seconds. Tap the Jog Dial. The headset automatically
restores the default settings and turns o.
Fault Reset
If the 10S is not working properly for any
reason, push the pin-hole reset button
located on the back of the headset.
Quick Start Guide
Motorcycle Bluetooth®
Communication System
2
3
You can start or end a two-way intercom
conversation with each headset.
Preset (#)”
“
3. Run the Sena Smartphone App. Swipe the screen to the right and tap
Setting to congure the headset settings.
(#)”
“
Save preset
“
(#)”
Delete preset
“
(#)”
Sena Technologies, Inc.
www.sena.com
Customer Support: support.sena.com
E-mail: support@sena.com
You can download the full version of the manual and view other
Sena products at the Sena website: www.sena.com.
16.Feb
Loading...