Sega OLLIE KING 29INCH DELUXE TYPE User Manual
1ST PRINTING MAY ‘04
®
www.sauservice.com
29 inch Deluxe Version
Owner’s Manual
SEGA AMUSEMENTS USA, INC.
MANUAL NO. 999-2026
GAME CODE: OLS
VISIT OUR WEBSITE!
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
To maintain the safety:
To ensure the safe usage of the product, be sure to read the following before using the product. The
following instructions are intended for the users, operators and the personnel in charge of the opera
tion of the product. After carefully reading and sufficiently understanding the warning displays and
cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.
Herein, explanations which require special attention are enclosed with dual lines. Depending on the
potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.
-
Indicates that mishandling the prod
uct by disregarding this warning
will cause a potentially hazardous
WARNING!
situation which can result in death
or serious injury.
-
CAUTION!
Indicates that mishandling the product
by disregarding this caution will cause
a slight hazardous situation which can
result in personal injury and or material
damage.
For the safe usage of the product, the following pictographs are used:
Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment,
this display is attached to places where the Owner’s Manual and or Service Manual should
be referred to.
Perform work in accordance with the instructions herein stated.
Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to
perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the
serviceman should perform such work.
Be sure to turn off power before working on the machine.
To prevent electric shock, be sure to turn off power before starting the work in which the worker touches
the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual
herein always states to that effect.
Be sure to ground the Earth Terminal (this, however, is not required in the case where a power cord
with earth is used).
This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Ter
minal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is
grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the
Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.
Ensure that the Power Supply used is equipped with an Earth Leakage Breaker.
This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not
equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.
Be sure to use fuses which meet the specified rating.
Using fuses exceeding the specified rating can cause a fire and electric shock.
(only for the machines which use fuses).
-
Specification changes (removal of equipment, conversion and addition) not designated by SEGA
are not allowed.
The parts of the product include warning labels for safety, covers for personal protection, etc. It is
very hazardous to operate the product by removing parts and or modifying the circuits. Should doors,
lids and protective parts be damaged or lost, refrain from operating the product, and contact where the
product was purchased from or the office herein stated. SEGA shall not be held responsible for any
accidents, compensation for damage to a third party, resulting from the specifications not designated by
SEGA.
Ensure that the product meets the requirements of appropriate Electrical Specifications.
Before installing the product, check for Electrical Specifications. SEGA products have a nameplate
on which Electrical Specifications are described. Ensure that the product is compatible with the power
supply voltage and frequency requirements of the location. Using any Electrical Specifications different
from the designated Specifications can cause a fire and electric shock.
Install and operate the product in places where appropriate lighting is available, allowing warning
labels to be clearly read.
To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated
has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated.
When handling the Monitor, be very careful. (Applies only to the product w/monitor.)
Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some
portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be
performed only be those technical personnel who have knowledge of electricity and technical expertise.
Be sure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.)
Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the
monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers.
When transporting or reselling this product, be sure to attach this manual to the product.
In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction
Manual of such equipment.
•
Descriptions herein contained may be subject to improvement changes without notice.
•
The contents described herein are fully prepared with due care. However, should any question arise or
errors be found, please contact SEGA.
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after
transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before
turning on power, check the following points to ensure that the product has been transported in a satisfactory status.
Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?
Are Casters and Adjusters, damaged?
Do the power supply voltage and frequency requirements meet with those of the location?
Are all wiring connectors correctly and securely connected? Unless connected in the correct direction,
connector connections can not be made accurately. Do not insert connectors forcibly.
Do power cords have cuts and dents?
Do the fuses used meet specified rating? Is the Circuit Protector in an energized status?
Are all accessories available?
Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?
TABLE OF CONTENTS
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
TABLE OF CONTENTS
INTRODUCTION OF THE OWNER’S MANUAL
1. HANDLING PRECAUTIONS ..........................................................................................
2. PRECAUTIONS CONCERNING INSTALLATION LOCATION ...................................
3. PRECAUTIONS REGARDING PRODUCT OPERATION .............................................
4. PART DESCRITIONS .......................................................................................................
5. ACCESSORIES .................................................................................................................
6. ASSEMBLING AND INSTALLATION ............................................................................
7. PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE ........................
8. GAME DESCRIPTION .....................................................................................................
9. EXPLANATION OF TEST AND DATA DISPLAY .........................................................
9 - 1 SWITCH UNIT AND COIN METER ............................................................
9 - 2 SYSTEM TEST MODE ..................................................................................
9 - 3 GAME TEST MODE ......................................................................................
10. MAINTENCE OF SKATEBOARD MECHANISM UNIT ...............................................
10 - 1 ADJUSTING/REPLACING THE TILT DETECTION VOLUME CONTR
10 - 2 GREASING ....................................................................................................
10 - 3 REPLACING THE BELLOWS ....................................................................
11. COIN SELECTOR ............................................................................................................
12. MONITOR ........................................................................................................................
13. REPLACING THE FLOURESCENT LAMP/OTHER LAMPS ......................................
14. PERIODIC INSPECTION TABLE ..................................................................................
15. TROUBLESHOOTING ....................................................................................................
16. GAME BOARD ................................................................................................................
16 - 1 REMOVING THE GAME BOARD ..............................................................
16 - 2 REMOVING THE GD-ROM DRIVE ...........................................................
16 - 3 COMPOSITION OF GAME BOARD ...........................................................
16 - 4 REPLACING THE MAIN BOARD BATTERY ............................................
16 - 5 REPLACING THE MEDIA BOARD BATTERY PACK ..............................
16 - 6 SHIPPING THE GAME BOARD AND CARTON BOX ..............................
17. NETWORK PLAY ............................................................................................................
17 - 1 PRECAUTIONS REGUARDING NETWORK PLAY SETUP ...................
17 - 2 CONNECTING NETWORK CABLES .......................................................
17 - 3 NETWORK PLAY SETTINGS ...................................................................
17 - 4 GENERAL PRECAUTIONS REGARDING NETWORK PLAY .................
18. DESIGN RELATED PARTS ...........................................................................................
19. PARTS LIST ...................................................................................................................
20. WIRE COLOR CODE TABLE ........................................................................................
21. WIRING DIAGRAM .......................................................................................................
1
3 - 4
5 - 11
12 13 - 14
15 - 35
36 - 37
38 - 47
48 - 73
50
51 - 63
64 - 73
74 - 82
75 - 78
79
80 - 82
83 - 84
85 - 87
88 - 90
91 - 92
93 - 97
98 - 114
99 - 105
106
107
108
109 - 111
112 - 114
115 - 122
115 - 116
117 - 120
121 - 122
122
123
124 - 138
139
XXX
SPECIFICATIONS
Installation Space : 32.8 inches width X 87.4 inches depth
Height : 84 inches
Width : 32.8 inches
Length : 87.4 inches
Weight : 634.9 lbs
Power, maximum current : 336 W 3.44 A (AC 120V 60 Hz AREA)
MONITOR : 29 inch supplied by Sanwa
Monitor Part# 998-0162
Chassis Part# 998-0161
INTRODUCTION OF THE OWNERS MANUAL
This Owner's Manual is intended to provide detailed descriptions together with all the
necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the product,
OLLIE KING 29INCH DELUXE TYPE.
This manual is intended for the owners, personnel and managers in charge of operation
of the product. Operate the product after carefully reading and sufficiently understanding the instructions. If the product fails to function satisfactorily, non-technical personnel
should under no circumstances touch the internal system. Please contact where the product was purchased from.
Use of this product is unlikely to cause physical injuries or damages to property. However,
where special attention is required this is indicated by a thick line, the word "IMPORTANT"
and its sign in this manual.
Indicates that mishandling the product by disregarding this display can cause the
STOP
product's intrinsic performance not to be obtained, resulting in malfunctioning.
IMPORTANT!
SEGA AMUSEMENTS USA, INC. / CUSTOMER SERVICE
45133 Industrial Drive, Fremont, California 94538, U.S.A.
Phone : (415) 701-6580
Fax : (415) 701-6594
DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN
LISTED
U
L
®
5K92
AMUSEMENT MACHINE
Non-technical personnel who do not have technical knowledge and expertise should
refrain from performing such work that this manual requires the location's main
WARNING!
Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the
location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work
should be performed by the serviceman who has technical expertise and knowledge.
The location's maintenance man and serviceman are herein defined as follows:
"Location's Maintenance Man" :
Those who have experience in the maintenance of amusement equipment and vending machines, etc.,
and also participate in the servicing and control of the equipment through such routine work as equip
ment assembly and installation, servicing and inspections, replacement of units and consumables, etc.
within the Amusement Facilities and or locations under the management of the Owner and Owner's
Operators of the product.
tenance man or a serviceman to carry out, or work which is not explained in this
manual. Failing to comply with this instruction can cause a severe accident such
as electric shock.
-
-
Activities of Location's Maintenance Man :
Assembly & installation, servicing & inspections, and replacement of units & consumables as regards
amusement equipment, vending machines, etc.
Serviceman :
Those who participate in the designing, manufacturing, inspections and maintenance service of the
equipment at an amusement equipment manufacturer.
Those who have technical expertise equivalent to that of technical high school graduates as regards
electricity, electronics and or mechanical engineering, and daily take part in the servicing & control
and repair of amusement equipment.
Serviceman's Activities :
Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of
amusement equipment and vending machines.
Notes:
1. HANDLING PRECAUTIONS
When installing or inspecting the machine, be very careful of the following points and pay attention to
ensure that the player can enjoy the game safely.
Non-compliance with the following points or inappropriate handling running counter to the cautionary
matters herein stated can cause personal injury or damage to the machine.
● Before performing work, be sure to turn power off. Performing the work without
turning power off can cause an electric shock or short circuit. In the case work
WARNING!
should be performed in the status of power on, this manual always states to that effect.
● To avoid electric shock or short circuit, do not plug in or unplug quickly.
● To avoid electric shock, do not plug in or unplug with a wet hand.
● Do not expose Power Cords and Earth Wires on the surface, (floor, passage, etc.).
If exposed, the Power Cords and Earth Wires are susceptible to damage. Damaged
cords and wires can cause electric shock or short circuit.
● To avoid causing a fire or electric shock, do not put things on or damage Power
Cords.
● When or after installing the product, do not unnecessarily pull the power cord. If
damaged, the power cord can cause a fire or electric shock.
● In case the power cord is damaged, ask for replacement through where the product
was purchased from or the office herein stated. Using the cord as is damaged can
cause fire, electric shock or leakage.
● Be sure to perform grounding appropriately. Inappropriate grounding can cause an
electric shock.
● Be sure to use fuses meeting specified rating. Using fuses exceeding the specified
rating can cause a fire or electric shock.
● Completely make connector connections for IC BD and others. Insufficient inser-
tion can cause an electric shock.
● Specification changes, removal of equipment, conversion and/or addition, not desig-
nated by SEGA are not permitted.
• Failure to observe this may cause a fire or an electric shock. Non-compliance with
this instruction can have a bad influence upon physical conditions of the players or
the lookers-on, or result in injury during play.
• SEGA shall not be held responsible for damage, compensation for damage to a third
party, caused by specification changes not designated by SEGA.
● Be sure to perform periodic maintenance inspections herein stated.
1
www.seuservice.com
STOP
IMPORTANT!
● For the IC board circuit inspections, only the logic tester is allowed. The use of a
multiple-purpose tester is not permitted, so be careful in this regard.
● The Projector is employed for this machine. The Projector's screen is susceptible
to damage, therefore, be very careful when cleaning the screen. For details, refer to
PROJECTOR.
● Static electricity from your body may damage some electronics devices on the IC
board. Before handling the IC board, touch a grounded metallic surface so that the
static electricity can be discharged.
● Some parts are the ones designed and manufactured not specifically for this game
machine. The manufacturers may discontinue, or change the specifications of, such
general-purpose parts. If this is the case, Sega cannot repair or replace a failed game
machine whether or not a warranty period has expired.
www.seuservice.com
2
2.
PRECAUTIONS REGARDING INSTALLATION LOCATION
This product is an indoor game machine. Do not install it outside. Even indoors, avoid
installing in places mentioned below so as not to cause a fire, electric shock, injury and
WARNING!
or malfunctioning.
● Places subject to rain or water leakage, or places subject to high humidity in the
proximity of an indoor swimming pool and or shower, etc.
● Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc.
● Places filled with inflammable gas or vicinity of highly inflammable/volatile chemicals or hazardous matter.
● Dusty places.
● Sloped surfaces.
● Places subject to any type of violent impact.
● Vicinity of anti-disaster facilities such as fire exits and fire extinguishers.
● The operating (ambient) temperature range is from 5˚ to 30˚.
LIMITATIONS OF USAGE REQUIREMENTS
● Be sure to check the Electrical Specifications.
Ensure that this product is compatible with the location's power supply, voltage and
WARNING!
frequency requirements.
A plate describing Electrical Specifications is attached to the product.
Non-compliance with the Electrical Specifications can cause a fire and electric shock.
● This product requires the Breaker and Earth Mechanisms as part of the location facilities. Using them in a manner not independent can cause a fire and electric shock.
● Ensure that the indoor wiring for the power supply is rated at 5 A or higher (AC
single phase 100~120 V area), and 3 A or higher (AC 220~240 V area). Non-compli
ance with the Electrical Specifications can cause a fire and electric shock.
● Be sure to independently use the power supply equipped with the Earth Leakage
Breaker. Using a power supply without the Earth Leakage Breaker can cause an
outbreak of fire when earth leakage occurs.
● Putting many loads on one electrical outlet can cause generation of heat and a fire
resulting from overload.
● When using an extension cord, ensure that the cord is rated at 5 A or higher (AC
100~120 V area) and 3 A or higher (AC 220~240 V area). Using a cord rated lower
than the specified rating can cause a fire and electric shock.
-
3
www.seuservice.com
2.5 m (98 in)
1.8 m (71 in)
10 cm (4 in)
OPERATION AREA
● For the operation of this machine, secure a minimum area of 1.8 m (W)×2.5 m (D).
WARNING!
● Be sure to provide sufficient space so as to allow this product's ventilation fan to
● SEGA shall not be held responsible for damage, compensation for damage to a
In order to prevent injury resulting from the falling down accident during game
play, be sure to secure the minimum area for operation.
function efficiently. To avoid machine malfunctioning and a fire, do not place any
obstacles near the ventilation opening.
third party, resulting from the failure to observe this instruction.
STOP
IMPORTANT!
For transporting the machine into the location's building, the minimum necessary dimensions of the opening (of doors, etc.) are 0.85 m (W) and
1.8 m (H).
Electric current consumption
MAX. 3.44 A (AC 120 V, 60 Hz)
MAX. 1.86 A (AC 220 V, 50 Hz)
MAX. 1.83 A (AC 220 V, 60 Hz)
MAX. 1.71 A (AC 240 V, 50 Hz)
MAX. 3.6 A (AC 110 V, 60 Hz,
For TAIWAN)
www.seuservice.com
FIG. 2
4
***Note: Actual Main unit WILL differ from image.
3. PRECAUTIONS REGARDING PRODUCT OPERATION
Ensure that all of the Adjuste
r
in contact with the floor.
BEFORE OPERATION
To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the
visitors and players.
In order to avoid accidents, check the following before starting the operation:
● To ensure maximum safety for the players and the customers, ensure that where the
WARNING!
product is operated has sufficient lighting to allow any warnings to be read. Opera
tion under insufficient lighting can cause bodily contact with each other, hitting ac
cident, and or trouble between customers.
● Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to
observe this can have a bad influence upon the players' or the customers' physical
conditions.
● It is suggested to ensure a space allowing the players who feel sick while playing the
game to take a rest.
● Check if all of the adjusters are in contact with the surface. If they are not, the Cabinet can move and cause an accident.
-
-
***Note: Actual Main unit WILL differ from image.
● Check that the safety parts are in good condition and securely attached. Accidents
may occur if this product is operated with defective safety parts.
5
www.seuservice.com
Are the bellows in good condition?
Is the safety bar attached securely
without any slack or free-movement?
Are the side panels undamaged
and attached securely?
● Perform a test run. Check that there are no defects in
WARNING!
the following parts.
CAUTION!
● Do not put any heavy item on this product. Placing any heavy item on the product
can cause a falling down accident or parts damage.
● Do not climb on the product. Climbing on the product can cause falling down
accidents. To check the top portion of the product, use a step.
● To avoid electric shock, check to see if door & cover parts are damaged or omitted.
● To avoid electric shock, short circuit and or parts damage, do not put the following
items on or in the periphery of the product.
Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/containers/
vessels containing chemicals and water.
To avoid injury, be sure to provide sufficient space by considering the potentially
crowded situation at the installation location. Insufficient installation space can cause
making bodily contact with each other, hitting accidents, and or trouble between cus
tomers.
***Note: Actual Main unit WILL differ from image.
-
www.seuservice.com
6
DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)
To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the
visitors and players.
● To avoid injury and accidents, those who fall under the following categories are not
allowed to play the game.
WARNING!
• Those who need assistance such as the use of an apparatus when walking.
• Those who have high blood pressure or a heart problem.
• Those who have experienced muscle convulsion or loss of consciousness when playing
video game, etc.
• Those who have a trouble in the neck and or spinal cord.
• Intoxicated persons.
• Pregnant women or those who are in the likelihood of pregnancy.
• Persons susceptible to motion sickness.
• Persons whose act runs counter to the product's warning displays.
● A player who has never been adversely affected by light stimulus might experience
dizziness or headache depending on his physical condition when playing the game.
Especially, small children can be subject to those conditions. Caution guardians of
small children to keep watch on their children during play.
● Instruct those who feel sick during play to have a medical examination.
● To avoid injury resulting from falling down and electric shock due to spilled drinks,
instruct the player not to place heavy items or drinks on the product.
● To avoid electric shock and short circuit, do not allow customers to put hands and
fingers or extraneous matter in the openings of the product or small openings in or
around the doors.
● To avoid falling down and injury resulting from falling down, immediately stop the
customer's leaning against or climbing on the product, etc.
● To avoid electric shock and short circuit, do not allow the customers to unplug the
power plug without a justifiable reason.
● Only players who satisfy the
minimum height requirement and
can hold the safety bar correctly
while riding the skateboard may
play.
Warn persons below the minimum
height requirement of 1.3m that
they are prohibited from playing.
Do not allow anyone to play
unless they hold the safety bar at
all times.
7
www.seuservice.com
● Warn anyone wearing high heel shoes that they are prohibited
WARNING!
● Similarly, warn anyone wearing sandals or other easily removed shoes that they are
● To avoid injury from potential falling down
from playing since there is a high risk of injury from accidents.
prohibited from playing since there is a high risk of injury from accidents.
accidents, be sure to instruct that only one
person is allowed to play at a time.
● Do not allow players to put any heavy
item or beverages on the product. Falling
down items can cause accidents and spilled
beverages can cause electric shock.
www.seuservice.com
8
● Instruct the player to hold on firmly to the Safety Bar during game. Caution the
customers who are most likely to cause injury by playing without holding the Safety
Bar, for example.
● To avoid injury, do not allow
persons other than the player to
access to the Rear Cabi during
game play.
❖ Instruct the player to play by
standing on both feet. Standing
on one leg to play can cause
injury.
9
www.seuservice.com
● Instruct the player not to put baggages, etc. on
the Rear Cabi to avoid damaging such items.
● Regarding this product, the weight of the
player is limited to 387 lbs. To avoid machine
damage and injury due to machine damage,
playing by those who are as heavy as 287 lbs.
or heavier is strictly prohibited.
● Immediately stop such violent acts as hitting and kicking the product. Such violent
acts can cause parts damage or falling down, resulting in injury due to fragments and
falling down.
www.seuservice.com
10
RUBBER MAT (For floor protectio
n
(Sold separately)
LEG RUBBER
(Accessories)
STOP
IMPORTANT!
● This product requires certain measures to prevent causing disruption to other nearby
game machines, etc. Playing this machine may hinder the operation of nearby game
machines due to vibration, etc. Fit the leg rubbers to the bottom of the adjuster feet,
and avoid setting up on wooden floorings.
● This product may scratch the floor surface of the installation site. If the floor surface
is wooden floorboards or carpeting, consider using a rubber mat or some other
means to protect the floor.
● Please take care not to offend or disturb customers when the machine is removed or
relocated to other places.
11
***Note: Actual Main unit WILL differ from image.
www.seuservice.com
ASSEMBLY (ASSY) TUBE
AC UNIT
REAR HATCH
COMMUNICATION PORT
CASHBOX DOOR
FRONT CABINET
REAR CABINET
BILLBOARD
29 TYPE MONITOR
CONTROL PANEL
SPEAKER
SAFETY BAR
SKATEBOARD
COIN CHUTE DOOR
SERVICE DOOR
4. PART DESCRIPTIONS
TABLE 4 Dimensions and Weights
Width × Depth × Height Weight
FIG. 4 b
FIG. 4 a OVERVIEW
***Note: Actual Main unit WILL differ from image.
FIG. 4 c REAR VIEW
ASSEMBLY (ASSY) TUBE
FRONT CABINET 30 in
BILLBOARD 30 in
REAR CABINET 33 in
FINAL PRODUCT 33 in
www.seuservice.com
× 37 in × 70 in 357 lbs
× 11 in × 16.6 in 16.5 lbs
× 49 in × 45 in 260 lbs
× 87 in × 84 in 635 lbs
12
5. ACCESSORIES
When transporting the machine, make sure that the following parts are supplied.
TABLE 5 a ACCESSORIES
DESCRIPTION OWNER'S MANUAL
Part No. (Qty.) 999-2026
Notes This manual
Figures
Parts not labeled with part numbers are as yet
unregistered or cannot be registered. Be sure to
handle all parts with care, as some parts are not
available for purchase separately.
CARTON BOX
601-11219-01 (1)
.
TAMPERPROOF WRENCH
M3 Torx Wrench (1)
Tool
KEY MASTER
220-5576 (2)
For opening/closing
the doors
KEY
(2)
For the CASHBOX DOOR
The Keys are inside the Coin
Chute Door at the time of shipment from the factory.
AC Cable (Power Cord)
600-7228
600-6618 (1) AC 220~240V AREA
ASSY FIBER CABLE (NETWORK CABLE) 2 m
600-7269-0200 (1)
ASSY FIBER CABLE (NETWORK CABLE) 5 m
600-7269-0500 (1)
13
www.seuservice.com
GD SOFT KIT OLS
Software
CUSHION SPONGE
601-11137
GD-ROM Disc Protector
GD-ROM DISC
DISC CASE
253-5507
www.seuservice.com
14
6. ASSEMBLY AND INSTALLATION
● Perform assembly work by following the procedure herein stated. Failing to
comply with the instructions can cause electric shock hazard.
WARNING!
● Perform assembling as per this manual. Since this is a complex machine, erroneous
assembling can cause an electric shock, machine damage and or not functioning as
per specified performance.
● When assembling, be sure to use plural persons. Depending on the assembly work,
there are some cases in which working by one person alone can cause personal
injury or parts damage.
● Ensure that connectors are accurately connected. Incomplete connections can cause
electric shock hazard.
● Be careful not to damage the wires. Damaged wires may cause electric shock or
short circuit or present a fire risk.
● This work should be performed by the site maintenance individual or other skilled
professional. Performing work by non-technical personnel can cause a severe
accident such as electric shock. Failing to comply with this instruction can cause a
severe accident such as electric shock to the player during operation.
● Provide sufficient space so that assembling can be performed. Performing work in
places with narrow space or low ceiling may cause an accident and assembly work
to be difficult.
● To perform work safely and avoid serious accident such as the cabinet's falling
down, do not perform work in places where step-like grade differences, a ditch, or
slope exist.
CAUTION!
● Handle molded parts with care. Undue weight or pressure may cause them to break
and the broken pieces may cause injury.
● To perform work safely and securely, be sure to prepare a step which is in a secure
and stable condition. Performing work without using the step can cause violent
falling down accidents.
● Make sure that the GD cable connector is inserted parallel to the plug. Improper
insertion may cause damage to the connector and present a fire risk.
15
www.seuservice.com
STOP
IMPORTANT!
● We recommend that the product is assembled at the proposed site of operation.
If there is any difference between the place of assembly and operation, it will
be necessary to dismantle and reassemble the product. Read section 7 for the
precautions regarding moving the machine.
● This product requires certain measures to prevent causing disruption to other nearby
game machines, etc. Playing this machine may hinder the operation of nearby game
machines due to vibration, etc. Fit the leg rubbers to the bottom of the adjuster feet,
and avoid setting up on wooden floorings.
● This product may scratch the floor surface of the installation site. If the floor surface
is wooden floorboards or carpeting, consider using a rubber mat or some other means
to protect the floor.
www.seuservice.com
16
REQUIRED TOOLS, IMPLEMENTS
Master key
Short Phillips head screwdriver (M5 screws)
Phillips head screwdriver (M5, M4 screws)
24 mm
24-mm spanner
When carrying out the assembling and installation, follow the following 7-item sequence.
CABINET-TO-CABINET CABLE CONNECTIONS
1
2
SECURING IN PLACE(ADJUSTER ADJUSTMENT)
3
INSTALLING THE GD-ROM DRIVE(SETTING GD-ROM DISC)
4
POWER SUPPLY, AND EARTH CONNECTION
5
TURNING POWER ON
ASSEMBLING CHECK
6
17
www.seuservice.com
FRONT CABINET SIDE
EARTH WIRE TERMINAL
REAR CABINET SIDE
SERVICE DOOR
1
CABINET-TO-CABINET CABLE CONNECTIONS
● Ensure that connectors are accurately connected. Incomplete connections can cause
WARNING!
● Be careful not to damage the wires. Damaged wires may cause electric shock or
Connect the cables between both cabinets by attaching the assembly tube to the front cabinet and rear
cabinet.
The matching connectors have the same number of pins and, therefore, can only be connected in one
direction. Avoid forcibly inserting the connectors as this may cause damage to the pins and cables.
electric shock hazard.
short circuit or present a fire risk.
At one end of the assembly tube there is a circular earth wire terminal. The tube end with the earth termi
nal connects to the rear cabinet side.
PHOTO 6. 2 a
● Remove the plastic locking nut from the front cabinet end of the assembly tube.
● Using the master key, unlock and detach the front cabinet service door.
-
www.seuservice.com
PHOTO 6. 2 b
18
TRUSS SCREW (3), black
M4×12
Fasten the connector.
● Feed the assembly tube wires
through the hole in the bottom of the
front cabinet floor panel, insert the
end connector and lock in place by
tightening the plastic locking nut.
Be careful to avoid pinching the wires
when doing this.
● Connect the assembly tube cable
connector to the connector inside the
front cabinet.
PHOTO 6. 2 c
***Note: Actual Main unit WILL differ from image.
● From the rear cabinet, detach the front
floor sash facing the front cabinet.
Remove the three truss screws.
PHOTO 6. 2 d
***Note: Actual Main unit WILL differ from image.
PHOTO 6. 2 e
19
www.seuservice.com
FLAT HEAD SCREW (4)
M4×12
FLOOR DESIGN SHEET
TUBE MOUNT LID
● Remove the two truss screws and detach the floor side sashes locking the left and right sides of the rear
FLOOR SIDE SASH
TRUSS SCREW (2ea), blac
k
M4×25
cabinet floor design sheet. The left and right side floor side sash components are different. Be careful to
return these to their correct original positions.
PHOTO 6. 2 f
● Pull up the floor design sheet carefully
to reveal the tube mount lid.
● Remove the four flat head screws
locking the tube mount lid and detach
the lid.
www.seuservice.com
20
PHOTO 6. 2 g
PHOTO 6. 2 h
Fasten the connector.
HEXAGON NUT (1)
M4 flat & spring washers used
● Remove the plastic locking nut from
the rear cabinet end connector of the
assembly tube.
● Feed the assembly tube wires through
the hole in the bottom of the rear
cabinet floor panel, insert the end
connector and lock in place by
tightening the plastic locking nut.
Be careful to avoid pinching the wires
when doing this.
● Next to the hole in the rear cabinet
floor panel there is a stud for
tightening the circular earth wire
terminal. Insert the circular earth
wire terminal, flat washer, and spring
washer in that order and then tighten
with the hexagon locking nut.
PHOTO 6. 2 i
***Note: Actual Main unit WILL differ from image.
● Connect the assembly tube cable
connector to the connector inside the
rear cabinet.
PHOTO 6. 2 j
***Note: Actual Main unit WILL differ from image.
PHOTO 6. 2 k
***Note: Actual Main unit WILL differ from image.
21
www.seuservice.com
● Lock the tube mount lid in position using the four flat head screws. Attach the floor side sashes to the left
and right sides of the floor design sheet and lock in position with the two truss screws. The left and right
side floor side sash components are different.
● Attach the front floor sash and lock in position with the three truss screws.
● Attach the front cabinet front service door and lock it.
***Note: Actual Main unit WILL differ from image.
PHOTO 6. 2 l
www.seuservice.com
22
Loading...