Securitron ICPT Installation Instructions
Securitron Magnalock Corp.
www.securitron.com
PowerJump Mounted Dimensions
Tel 800.624.5625
ASSA ABLOY, the global leader
in door opening solutions
Securitron Magnalock Corp.
www.securitron.com
Tel 800.624.5625
PowerJump™ ICPT
Installation Instructions
Package Contents
ASSA ABLOY, the global leader
in door opening solutions
How does it work?
1 1/4”
Wood Mount
Face
2 3/4”
Hard Wood 3/32” x 3/4” deep
Soft Wood 1/16” x 2” deep
1 7/8”
2 1/8”
Depth
Frame Unit
1 3/8”
Door Unit
1 5/8”
1/8” face depth
5”
4”
mounting
tabs (2)
Metal Mount
Face
1 1/4”
Door side unit (red wire)
(4) Metal mounting tabs
for an online video
(8) 10/32 flathead machine screws
(4) 8/32 flathead machine screws
(4) #8 1” wood screws
(4) #8 2 1/8” wood screws
Recommended Tools
Screwdriver, drill, center punch
wire nuts (22 gauge), tape
Door Wedge
(4) Installation templates (not shown)
Rotary tool with cutting wheel
1/4” metal drill bit
82° countersink bit
Frame side unit (purple wire)
(8) Metal mounting spacers
Wood Mounting Tools:Metal Mounting Tools:
Wood chisel and hammer
3/32” and 1/16” wood drill bits
1” Auger bit
Specification
Input power at frame side: 500mA at 24V DC
Output power (selectable voltage) at door side: 250mA at 24V DC or 500mA at 12V DC
Operating temperature: 32 to 120 F / 0 to 49 C
Maximum gap between faces: 3/16”
Compatibility: PowerJump does not support LBM, REX or other signals from the lock
Overview
The PowerJump ICPT transfers power across a door gap through magnetic inductive coupling.
Installation Steps
Step 1: Survey installation site
Unit may be installed on latch side, hinge side, top or bottom of door. Note the ICPT requires a
depth of 1 3/8” in the frame and 1 5/8” in the door.
Scan the QR code
1/4” bit (4) places
82° countersink
Troubleshooting:
Check voltage at frame side unit is within 24V +/- 10%
Check voltage on door side with door closed and unit under load with flying leads
Check air gap between faces is 3/16” or less. Frame side unit can be shimmed outward to improve performance.
Remove unit
Cut shims
Attach
Shims
Questions about Installation?
Contact Securitron at: 1-800-MAGLOCK (800-624-5625)
© Copyright, 2012, all rights reserved 500-24025
Page 4
Replace unit
Rev A, 11/12
Step 2: Select the template matching your door and frame material. Apply the
templates as shown at the desired mounting location. Make sure the
center line arrows are aligned when the door is closed.
Align center line
of templates with
door closed
Door
© Copyright, 2012, all rights reserved
Frame
Page 1
Door Frame
500-24025
Rev A, 11/12
Securitron Magnalock Corp.
www.securitron.com
Tel 800.624.5625
Step 3: Installing in a WOOD door or frame
Wood A: Carefully tap a chisel through the
template to score the finish. Pre-Drill (2)
mounting holes according to wood type.
ASSA ABLOY, the global leader
in door opening solutions
Wood B: Carefully drill out the pocket
with the auger bit, to a depth of 1 5/8”
Use a wood chisel to straighten the sides
Be careful not to damage the surface
Tip: mark the auger
bit with tape at a
depth of 1 5/8”
Drill to this depth
Securitron Magnalock Corp.
www.securitron.com
Tel 800.624.5625
Step 4: Installing in a METAL door or frame
Metal A: Drill (4) mounting tab holes with 1/4”
drill bit countersink with 82° bit
Metal B: Cut main pocket with rotary tool using a
metal cutting wheel or a metal cutting saw
Metal C: Test fit and file opening
ASSA ABLOY, the global leader
in door opening solutions
Hard Wood: 3/32” bit, 3/4“ deep
Soft Wood: 1/16” bit, 2” deep
Wood C: Cut relief for faceplate
using a chisel to a depth of 1/8”
Wood E: Test fit the unit into the
pocket and file if needed
Wood D: Drill a wiring channel for
connection to the device to be powered
Metal D: Install mounting tabs using (4) 10/32 screws.
Attach adhesive spacers as needed to mount the unit flush with the frame
Tip: For 18 gauge metal use
(2) of the included spacers
Step 5: Voltage Selection and Wiring
a) Select output voltage of 12V or 24V. Move the two jumpers as shown:
12V
output
24V
output
b) Supply 24V DC power to frame unit. Connect purple wire to positive (+)
and black wire to (-). Connect door side electrified device via wiring channel,
connect red wire to (+) and black wire to (-)
24V
Power
Supply
(+)(+)
(-)
Access Control
C
NO
Frame
Unit
Purple (+)
Black (-)
Door
Unit
Red (+)
Black (-)
12V / 24V
Powered
Latch
Step 6: Mount PowerJump
© Copyright, 2012, all rights reserved
Page 2
500-24025
Rev A, 11/12
Wood: Use (2)
#8 wood screws
Metal: Use (2)
8/32 machine screws
Hard Wood: 1” Screws
Soft Wood: 2 1/8” Screws
to mount to tabs
© Copyright, 2012, all rights reserved 500-24025
Page 3
Rev A, 11/12
Loading...