Seco-Larm SLI 762PP-ISS Specsheet

Tel: [phone] (Domestic U.S. & Canada) Email: [e-mail] Website: www.seco-larm.com
16842 Millikan Avenue, Irvine, CA 92606 Tel: [phone] (California and International) Fax: [phone]

pi-SLI 762FP-ISS 2.docx

Copyright © 2010 SECO-LARM U.S.A., Inc. All rights Reserved.
The SECO-LARM policy is one of continual development. For that reason SECO-LARM reserves the right to change prices and specifications without notice. SECO-LARM is not responsible for misprints.

Passive Proximity Immobilizer

Features:

 Fully automatic arming 30 seconds after ignition is turned off.
 Simple disarming. Immobilizer automatically reads

Controller when starting ignition. No buttons to push.

 Immobilization of up to 3 electrical circuits (e.g. starter,

ignition, fuel pump) once system is armed.

 2 Built-in 30-Amp relays and 1 transistor output.
 2 Controllers supplied with each unit. Up to 4 controllers

can be learned with simple code learning procedure.

 Each controller has millions of possible code combinations.
 Unique security code for override if controller is lost or stolen.
 The flexible sensing coil can be mounted in many positions

to make installation easier.

 LED flashes to indicate Immobilizer is armed, disarmed,

or triggered.

 Stealth installation—all black wires to help prevent tampering.
 All code information is stored in non-volatile EEPROM

memory to protect data in case of power loss.

 Multiple car operation—One controller can work with

multiple vehicles.

Specifications:

SLI 762PP-ISS

The SLI 762PP-ISS Passive Proximity Immobilizer combines high security with completely passive arming and disarming.
Just attach the mini controller to the key chain. Each time the driver turns the ignition on to start the engine, the Immobilizer
automatically reads the controller, disarms the system, and allows the vehicle to start.

Operating voltage

9~15 VDC

Current draw (standby)

10mA@12VDC

Current draw (active)

230mA@12VDC

Number of relays

2

Relay rating

30A@12VDC

Operating temperature

-40°~185° F (-40°~85° C)

Built-in Multifunction LED:

Passive Operation:

Status

LED indicator

Arming

Fast flash

Armed

Slow flash

Disarmed

Off

Triggered

On

Indicates arming,

armed, disarmed,

and triggered

modes.

The Immobilizer

automatically detects the

controller and disarms the

vehicle for use.

Tel: [phone] (U.S. & Canada) Email: [e-mail] Website: www.seco-larm.com

16842 Millikan Avenue, Irvine, CA 92606 Tel: [phone] (California and International) Fax: [phone]

pi-SLI 762PP-ISS 2.docx

Vehicle

5A

Ignition coil

* DIODE 1N4001

(optional)

Fuel

Pump

Constant
+12VDC

Switched

+12VDC

30

85

86

87

87a

Ground (Black label)

Ground (Black label)

Ground (Black label)

Ground (Black label)

Black 2-strand

Deactivation

Coil

Circuit 2

3

Circuit 1

3

(Green label)

NOTE—This wire
must show + 12V
when the ignition
switch is in the ON
and START position.

Black heat shrink

Black heat shrink

LED

(Black label)

(Black label)

Two separate sources of
chassis ground.
(White label)

N.O. door (—) switch
(Yellow1 label)

Switched

+ 12VDC

(Red2 label)

Constant
+ 12VDC

5A

* DIODE 1N4001

(optional)

Fuel

Pump

Switched

+12VDC

30

85

86

87

87a

.

.

5A

NOTES:

1. YELLOW label ignition wire must be connected at all times for proper operation.

2. RED label power wire must be connected via 5A fuse.

3. Circuit 1 or Circuit 2 must be used to disable the starter in order to be consistent with

explanations in the Owner’s Manual.

Wiring Diagram: