Page 1
•
Features
:
SL-3301-BAQ
Multi-Color LED Strobe Light
Manual
• 7 Colors possible – Red, green, blue,
cyan, magenta, yellow, and white
• Operating life of over 50,000 hours
(over 5.7 years)
• Simple 2- to 5-wire installation
• Set color via DIP switches, or trigger
colors with an external device via 3
trigger input wires
Utilizes high-intensity LEDs
• 5 Vertical LED strips (25 LEDs total)
increase visibility from various directions
• Adjustable strobe speed, 60~260 times/min
• High-impact resistant case
• High-impact and heat-resistant lens
• Reverse polarity protection
• Weather resistant – IP66
Page 2
ENFORCER Multi-Color LED Strobe Light
The
ENFORCER
Multi-Color
LED Strobe Light
provide
s all the functions of a re
gular strobe light, but with
Overview:
Parts List:
1x LED Strobe Light
1x
Manual
2x
Mounting Screw
with “O” ring
Specifications
:
Vertical LED strips
5
Total number of LEDs
25
Possible colors
Red, green, blue, cyan, magenta,
yellow, white
Operating voltage
9~24 VAC/VDC
Strobe
350mA
Steady ON
350mA
Maximum setting
260 times/min
Minimum setting
60 times/min
Operating life
Over 50,000 hours (over 5.7 years)
Operating
temperature
-4°~144
° F (-
20°~65
° C)
Electrical protection
Reverse polarity protected
IP rating
IP66
Base High-impact
resistant
black ABS
Lens High-impact
heat-resistant acrylic
Dimensions
315/16"
x31/8" (100x79
mm)
Ground wire
(black)
LEDs
LED
Strobe or
Remove thinned
-
Circuit board screw
Trigger wires
®
SL-3301-BAQ
-
B1 B2 G1 G2 R1 R2
Blue
Green
Red
Mounting screw with
Blue trigger wire
Introduction
:
more versatility. The Multi-Color LED Strobe Light can change between seven different colors which can be
set manually via DIP switches, or triggered by an external device via 3 trigger input wires. There are 5 vertical
LED strips, making the light more visible from various directions, and a variable resistor to adjust flashing
speed. The Multi-Color LED Strobe Light has an operating life of 50,000 hours — over 160 times that of a
regular strobe light. No more bulbs to replace!
Current draw @12VDC (max.)
Adjustable strobe speed
Red trigger wire
Green trigger wire
Power wire (brown)
out slot for
surface wiring
Circuit board
Vertical LED strips
rubber “O” ring
DIP Switches
(for Power ON mode)
2 SECO-LARM U.S.A., Inc.
SECO-LARM
Strobe
Steady ON
170–226
Strobe speed control
steady ON jumper
(default, strobe)
Strobe Steady ON
Rubber “O” ring
Circuit board
Page 3
ENFORCER Multi-Color LED Strobe Light
Configuring
LED Color and Strobe
:
1. Decide where the LED strobe light is to be mounted.
4. Remove the lens and mount the LED strobe light to
the surface using the two included mounting screws
(clockwise
Installation
:
B1 B2 G1 G2 R1 R2
Trigger Mode
•
Power ON Mode
1. Decide where the LED strobe light is to be mounted.
4. Remove the lens and mount the LED strobe light to
the surface using the two included mounting screws
LED
DIP Switch
Trigger Wire
NOTE:
For Trigger Mode,
LED
Before starting, please read this manual carefully and keep it for future reference.
• Be sure to use the LED strobe light within the given electrical limits.
Use a pencil to mark the location of the two mounting
screws.
2. Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and power (brown) wires through the wall.
NOTE: For surface wiring applications, remove the
thinned-out slot with a pair of pliers.
3. Connect the wires to their respective locations on an
alarm control panel or other security panel.
Use a pencil to mark the location of the two mounting
screws.
2. Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and trigger (blue, green, red) wires through the wall.
NOTE: For surface wiring applications, remove the
thinned-out slot with a pair of pliers.
3. Connect the wires to their respective locations on an
alarm control panel, other security panel, or trigger
device according to the color desired (see chart below).
with rubber “O” rings. If screws are fastened too
tightly, the “O” rings will be damaged.
5. Select the color and strobe setting using the DIP
Switches (see chart below for details) and adjust
the speed using the strobe speed control
to increase, counterclockwise to decrease).
6. Replace lens. If lens is fastened too tightly, the
“O” ring will be damaged.
with rubber “O” rings. If screws are fastened too
tightly, the “O” rings will be damaged.
5. Set the LEDs to "strobe" or "steady ON" via the
jumper, and adjust the strobe speed using the
strobe speed control (clockwise to increase,
counterclockwise to decrease).
6. Replace lens. If lens is fastened too tightly, the
“O” ring will be damaged.
IMPORTANT: Disconnect power before adjusting DIP switches.
Color Strobe Setting
Red
Green
Blue
Cyan
Magenta
Yellow
White
LEDs strobe continuously Strobe R2 ON only (default)
LEDs are steady ON Steady ON R1 ON only
LEDs strobe continuously Strobe G2 ON only
LEDs are steady ON Steady ON G1 ON only
LEDs strobe continuously Strobe B2 ON only
LEDs are steady ON Steady ON B1 ON only
LEDs strobe continuously Strobe G2 and B2 ON
LEDs are steady ON Steady ON G2 and B2 ON
LEDs strobe continuously Strobe R2 and B2 ON
LEDs are steady ON Steady ON R2 and B2 ON
LEDs strobe continuously Strobe R2 and G2 ON
LEDs are steady ON Steady ON R2 and G2 ON
LEDs strobe continuously Strobe R2, G2, and B2 ON
LEDs are steady ON Steady ON All ON
Jumper
Default DIP Switch Setting: Red strobe
Configuration
Connections
Connect red wire to GND
Connect green wire to GND
Connect blue wire to GND
Connect green and blue
wires to GND
Connect red and blue wires
to GND
Connect red and green
wires to GND
Connect all three trigger
wires to GND
strobe and steady on setting is set
with jumper, see Overview (pg. 2).
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Multi-Color LED Strobe Light
Dimensions:
NOTICE
:
The SECO
-
LARM policy is one of continual development and improvement. For that reason, SECO
-
LARM
SECO
-
LARM
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800 Email: sales@seco
-
larm.com
PITSW1
LED
SL-126LQ/WD
SL-1901-DAQ SL-1901-JAQ SL-1301-SAQ Series
Conduit Drop
Conduit Box
Both
SECO
-
LAR
M
•
•
WARRANTY:
This SECO
-
LARM product is warranted against defects in
material and workmanship while used in normal
Troubleshooting
:
Top View
Front View
Bottom View
315/16"
213/16"
21/8"
31/8"
(100mm)
The LED strobe light does not turn on
The LED strobe light does not flash correctly
Also Available from
Replacement
White Diffuser Lens
Conduit Drop Conduit Box
Conduit Application Photos
(79mm)
(54mm)
Check the LED strobe light’s power source
Disconnect power, reconfigure LED color and strobe
settings, and reconnect power
®
:
Strobe Lights
(71mm)
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2019 SECO-LARM U.S.A., Inc. All
rights reserved.
4 SECO-LARM U.S.A., Inc.
®
U.S.A., Inc.
Order Part#: 762-514%
MI_SL-3301-BAQ_190619.docx
Loading...