Seco-Larm SL-1301-SAQ-G, SL-1301-SAQ-R, SL-1301-SAQ-C, SL-1301-SAQ-A, SL-1301-SAQ-B User Manual
...
ENFORCER LED Strobe Lights
Configuring Flash Pattern
:
NOTICE
:
The information and specifications printed in this manual are current at the time of publication.
However, the
SECO
-
LARM
®
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800 Email:
sales@seco
-
larm.com
IMPORTANT: Before changing flash pattern,
disconnect power
. Change flash pattern before
DIP Switch
Description of
Replacement
Mounting Options
Xeon Tube
SL-126LQ/X
SL-126Q Series
Conduit Drop
Conduit Box
Both
SECO
SECOSECO
SECO
----
LAR
LARLAR
LAR
MMMM
All Models:
(SL-1301-S
AQ shown)
Red SL-1301-EAQ/R
SL-
1301-BAQ/R
SL-
1301-SAQ/R
*
Blue SL-1301-EAQ/B
SL-
1301-BAQ/B
SL-
1301-SAQ/B
*
Amber
SL-
1301-EAQ/A
SL-
1301-BAQ/A
SL-
1301-SAQ/A
*
Clear
SL-
1301-EAQ/C
SL-
1301-BAQ/C
SL-
1301-SAQ/C
*
Green
SL-
1301-EAQ/G
SL-
1301-BAQ/G
SL-
1301-SAQ/G
*
BAQ and SAQ series
also
include
:
LEDs
(SL-1301-BAQ/SL-1301-SAQ series only)
reconnecting power.
Visit www.seco-larm.com for animated flash pattern samples.
Position
1
2
LEDs flash on and off continuously. (Default setting)
Rotate Clockwise
Light rotates clockwise in a circular fashion continuously.
Flash Pattern
Strobe
(Beacon)
Top View
(SL-1301-BAQ Shown)
LED Strobe Lights
Manual
3
4
5
6
All LEDs stay on. Ideal for continuous lighting applications.
LEDs turn on progressively clockwise until all LEDs are lit
LED groups light up one at a time, rotating clockwise and
LEDs turn on progressively clockwise (sweep), then turn off
Also Available from
Lenses
Conduit Drop
(Replace ‘X’ with the first
letter of the desired color)
SL-1901-DAQ
Flash with Progressive ON/OFF
Steady ON
Flash with Progressive ON
(sweep), and then turn off.
Rotate Back and Forth
counterclockwise.
progressively counterclockwise.
®
:
Conduit Box
SL-1901-JAQ
Strobe Lights
Application Photos
Available in Red, Blue,
Amber, Clear, or Green
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
U.S.A., Inc.
4 SECO-LARM U.S.A., Inc.
Available in Red, Blue,
Amber, Clear, or Green
Order Part# 762-509-4%
MiSL-1301-xAQ_150123.docx
Color
*Includes a built-in 100dB siren
• Operating life of over 50,000 hours
(over 5.7 years)
• Same size as the SL-126Q strobe light
• Simple 2-wire installation
• 5 lens colors available for each model
• Weather resistant
Bright Brighter
• 6 different flashing options
• Adjustable flashing speed
• Backup battery available for continuous
lighting applications
• Vertical LED strips increase visibility from
various directions
Brightest
• High-impact resistant case
SAQ series also includes:
• Built-in 100dB siren (programmable)
®
PITSW1
• High-impact and heat-resistant lens
• Reverse polarity protection
• Visible in all directions
ENFORCER LED Strobe Lights
ENFORCER LED Strobe Lights
provide all the functions of a regular strobe light and much more. Each has
Top View
Dimensions
:
Front View
Bottom View
315/16”
24/5”
23/64”
229/32”
Parts List:
1x LED Strobe Light
1x
Manual
2x
Mounting Screw
with “O” ring
Specifications
:
SL-
1301-EAQ SL-
1301-BAQ SL-1301-SAQ
LEDs
on circuit board
Yes No Yes
LEDs
on vertical
strips No
Yes Yes
Rotate clockwise
N/A1 30mA 9
0mA
Strobe
200mA 10
0mA 15
0mA
Steady ON
N/A1 100mA 15
0mA
Flash with progressive ON
N/A1 100mA 15
0mA
Rotate back
and forth
N/A1 100mA 15
0mA
Flash with progressive ON/OFF
N/A1 100mA 15
0mA
Adjustable flash pattern
No1
Yes Yes
# of flash patterns
11 6 6
Maximum setting
260 times/min
260 times/min
Minimum setting
30
times/min
30 times/min
Operating life
Over 50,000 hours (over 5.7 years)
Backup battery
function
No Yes Yes
Steady ON
N/A Up to 4
hours3 Up to 2
hours3
Strobe/Flashing
N/A Up to 5
hours3
Up to 2
hours3
Operating temperature
-4°~144
° F (-
20°~65
° C)
Electrical protection
Reverse polarity protected
Built-in siren
No No
Yes (100dB)
IP rating
IP66 IP66 IP55
Base High-impact
resistant
black ABS
Lens High-impact
heat-resistant acrylic
Dimensions
315/16”x229/32” (100x74
mm)
SL-1301-EAQ series has strobe only
29VDC battery not included
Estimated
-
depending on mode
Introduction
:
Troubleshooting
:
•
•
Backup Battery
For continuous lighting applications, the backup battery will
9-Volt Battery
1. Before starting, please read this manual carefully and
Insta
llation
:
6. Remove the lens and mount the LED strobe light to
the surface using the two included mounting screws
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship while used in normal service for one
Circuit board
(Circuit board)
Overview
:
®
Mounting screw with
9-Volt battery
clip
Backup battery jumper
(default off)
Strobe speed
c
ontrol
DIP switch
Remove
out slot
Siren jumper
(default off)
+
ENFORCER LED Strobe Lights
an operating life of 50,000 hours—over 160 times that of a regular strobe light. No more bulbs to replace!
There are three models—with 12~54 LEDs. The BAQ series and SAQ series include a unique placement of
LEDs making the light more visible from various directions, a 9V backup battery option making them ideal for
continuous lighting applications, and 6 selectable strobe patterns with adjustable strobe speed. The SAQ
series also includes a built-in 100db siren.
Operating voltage 6~12 VDC 9~12 VDC
Current drain
@12VDC (max)
Adjustable
flashing speed
Backup battery
2
life
1
2
Fixed
130 times/min
3
10~24
VAC/VDC
Ground wire (black)
Power wire (red)
(BAQ and SAQ series only)
(under circuit board)
(BAQ and SAQ series only)
(SAQ series only)
LED strips
(depending on model)
Circuit board LEDs
(depending on model)
keep it for future reference.
2. Be sure to use the LED strobe light within the given
electrical limits.
3. Decide where the LED strobe light is to be mounted.
Use a pencil to mark the location of the two mounting
screws.
4. Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and power (red) wires through the wall.
Note: For surface wiring applications, remove the
thinned-out slot with a pair of pliers.
5. Connect the wires to their respective locations on an
alarm control panel or other security panel.
(BAQ and SAQ series only)
OFF ON
ON/OFF BAT.
SP ON/OFF
Max
SECO-LARM
(SL-1301 BAQ/SL-1301-SAQ series only)
power the LED strobe light in the event of a power loss.
1. Use a screwdriver to loosen the circuit board screws.
2. Carefully remove and flip the circuit board. The battery
holder is attached at the back side of the circuit board.
3. Connect a 9-Volt battery to the battery connector.
4. Replace circuit board and circuit board screws.
5. Turn the backup battery on via the backup battery jumper.
SL-1301-SAQ shown
thinned-
for surface
wiring
rubber “O” ring
OFF ON
1 2 3 4
with rubber “O” rings. If screws are fastened too
tightly, the “O” rings will be damaged.
(SL-1301-EAQ series skip to step 10)
7. Select the flash pattern using the DIP Switch (see
back page for details) and adjust the speed using
the strobe speed control (clockwise to increase,
counterclockwise to decrease).
8. Set the siren (SL-1301-SAQ only) to on or off using
the siren jumper.
9. If needed, install backup battery. (See below.)
10. Replace lens. If lens is fastened too tightly, the
“O” ring will be damaged.
(not included)
(BAQ and SAQ series only)
Rubber “O” ring
Circuit board
Circuit board screw
screw
(100mm)
2 SECO-LARM U.S.A., Inc.
(74mm)
(52mm)
(71mm)
The LED strobe light does not turn on
The LED strobe light does not flash correctly
(1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if
the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God,
physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other
reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
SECO-LARM U.S.A., Inc. 3
Check the LED strobe light’s power source
Disconnect power, configure correct flash pattern, and
reconnect power
Loading...