SD-7286-GWQ
Flush-Mount Request-to-Exit Plate
Manual
ENFORCER Flush-Mount Request-to-Exit Plate
Features:
Large green 2” diameter pushbutton
Flush mount, protrudes only
9
/16” (15mm)
Aluminum back plate fits to single-gang box
ABS plastic front cover snaps to back plate
DPDT Momentary switch, 5A@125VAC contact rating
Specifications:
Model
SD-7286-GWQ
Contact rating
5A@125VAC (3A@12VDC)
Switch type
DPDT Switch (momentary)
Dimensions
41/2”x23/4”x19/16” (114x69.5x39 mm)
Overview:
Parts List:
1x Front cover
1x Back plate
2x Mounting screws
4
1
/
2
” (114mm)
23/4”
19/16”
Front View
Side View
2 SECO-LARM U.S.A., Inc.
ENFORCER Flush-Mount Request-to-Exit Plate
Installation:
1. Remove the back plate from the unit.
2. Thread the cable wire through the electrical
box and the center hole of the back plate.
3. Fasten the back plate to the electrical box
using the included mounting screws.
4. Connect the wires to the switch using the
wiring diagram below.
5. Finish assembly by snapping the front cover
onto the back plate.
Front cover
Back plate
Electrical box
(not included)
Switch
Mounting
screws
Wiring Diagram:
Sample Application:
Side View
1. Normally closed (N.C.) on
the SD-7286-GWQ is
connected to a keypad such
as the SD-1123-SQ. The
other N.C. terminal is
connected to power.
2. An electromagnetic lock,
such as the E-941SA-600, is
connected to normally closed
(N.C.) on the keypad’s relay.
3. Pressing the button on the
SD-7286-GWQ will open the
electromagnetic lock.
N.C.
COM
N.O.
RELAY
12 VDC
Power Supply
N.O.
N.C.
N.C.
N.O.
SD-7286-GWQ
Keypad
(SK-1123-SQ)
Electromagnetic Lock
(E-941SA-600Q)
N.O. (Normally Open)
N.C. (Normally Closed)
N.C. (Normally Closed)
N.O. (Normally Open)
SECO-LARM U.S.A., Inc. 3
ENFORCER Flush-Mount Request-to-Exit Plate
Single-Gang Mortise Cylinder Key Switch
SD-72081-6MQ
Indoor No-Touch Sensor
SD-927PKC-NEQ
Outdoor No-Touch Sensor with
Manual Override
SD-9263-KSVQ
Mushroom Request-to-Exit Plate
SD-7201GC-PEQ
Illuminated Request-to-Exit Plate
SD-7202GC-PEQ
Piezoelectric Request-to-Exit Plate
SD-6276-SS1Q
For a complete listing of SECO-LARM products, please visit us online at www.seco-larm.com.
Also Available from SECO-LARM:
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
PITGW1
Phone: (949) 261-2999 | (800) 662-0800
Email: sales@seco-larm.com
MiSD-7286-GWQ_1405.docx
IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of
this product complies with all national, state, and local laws and codes related to locking and egress devices.
SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
4 SECO-LARM U.S.A., Inc.
Loading...