Seco-Larm SD-7251GCEX1Q User Manual

Illuminated Push-to-exit Plates Installation Manual

Other Popular Request-to-Exit Plates

SD-7275SGEX1Q SD-7202GC-PE SD-927PKC-NEQ

Illuminated vandal resistant

•

1”(25mm) diameter pushbutton

•

N.O./N.C. contact rated

•

5A @ 250 VAC.
Field selectable green/red color

•

LED light.
"EXIT" and "SALIDA"

•

silk-screened on plate.

Note: The SD-7202GC-PE is also available with timer.

WARNING: Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a
dangerous electric shock, damage the device, and void the warranty. Do not open the case of this device, as there are
no field-serviceable components inside.

WARRANTY

service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.

: This SECO-LARM product is warranted against defects in material and workmanship while used in normal

2" square green, illuminated,

•

momentary push button.
N.O./N.C. contact rated

•

10A @ 125 ~ 250 VAC.
Includes: "PUSH TO EXIT" &

•

"PRESIONE PARA SALIR"
button faces.

No Touch Request-To-Exit Plate.

•

Range up to 4” (10cm).

•

3A relay, triggers min. 0.5 sec. or as

•

long as hand is near the sensor.
Green LED-illuminated sensor area

•

for easy identification. LED turns red
to show the relay is triggered.
Quick connect screwless terminal

•

block.

Installation Manual

®

ENF ORCER

SD-7251GCEX1Q

Illuminated Mushroom-cap
Push-to-Exit Plate

Features:

Illuminated green 11/2” (40mm) dia. mushroon-cap button.

•

N.O./N.C. contact rated at 5A@125VAC.

•

“EXIT” and “SALIDA” silk-screen on plate.

•

Green illuminated pushbutton for easy identification.

•

Installation:

1. Run four wires through the wall to the back-box.

2. Connect 2 wires (12VDC) to the illumination terminals.
a) The illumination terminals are non-polarity.
a) For 24VDC operation, install supplied resistor (1K , 1/4

Watt) in line on the + illumination wire.

3. Connect 2 wires to either the N.C. (red color terminal) or
N.O.(blue color terminal) as required.

4. Screw plate to the back-box, using caution not to pinch any wires.

Bulb replacement:

1. If the LED bulb needs to be replaced, removed the yellow lever
cover as shown on Fig.1 by pulling it upward.

2. Move the lock lever counterclockwise as shown then pull off the
back portion (terminals) of the switch to expose the LED bulb.

3. Replace only with the same specification bulb. Using wrong
specification bulb will risk burning out the bulb and pushbutton
switch. Contact SECO-LARM for replacement bulb.

4. Put back the yellow lever cover after LED bulb has been replaced.

Illumination

Fig. 1 – Bulb replacement

terminal

(12VDC non-polarity)

17/16” (87mm)

21/2” (63mm)

Connections:

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the

SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2007 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in
whole or in part, without the written permission of SECO-LARM.

SECO-LARM® U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]

Website: www.seco-larm.com
E-mail: sales

@

seco-larm.com

SECO-LARM U.S.A., Inc.

SECO-LARM U.S.A., Inc.

FILE: DT/DTP/MiSD7251GCEX1Q.pmd

ORDER PART# 763-159%

PITSW1

Yellow lever cover

Lever

N.O. terminal

(Blue color)

Illumination

terminal

(12 VDC non-polarity)

N.C. terminal

(Red color)