•
•
®
RA-4961-VPQ
Wireless Vibrating Receiver
Manual
For use with RA-4961 series receivers
• Connect up to 4 wireless transmitter
accessories
• Audible, visual, and physical alert via built-
in speaker and vibration
Belt clip and small size for easy
portability
• Each channel independently
programmable
CBA Wireless Vibrating Receiver
Specifications:
Parts List:
1x Wireless vibrating receiver
1x Manual
Dimensions:
Overview:
Model number
RA-
4961-VPQ
Frequency
914.8MHz
Channels
4
Power supply
2x AA Batteries (Not included)
Current
Standby
1mA
Max 80mA
Est
imated battery life
60 days (3 triggers/day)
Receiver low battery indicator
Receiver beeps every 5 seconds
Accessory low battery indicator
Zone LED for accessory blinks
Sound level (dB)
76dB@1ft(30cm)
IP rating
IP 30
Operating temperature
32º~140º F (
0º~60º C)
Dimensions
29/16"x11/16"x39/16" (65x27x91 mm)
Weight (without batteries)
2.7-oz (78g)
Reset
Belt clip
11/16"
(27mm)
29/16"
(65
mm)
39/16"
(91
mm)
Channel
LEDs
Speaker
Front Side
Tone select
Channel
Notification
Battery
Battery cover
Back
draw
1
2
3
4
RESET
button
RESET
compartment
(removed)
Button
2 SECO-LARM U.S.A., Inc.
select
button
selection
switch
CBA Wireless Vibrating Receiver
Pairing Accessories:
1. Enter programming mode b
y holding down the channel select button until the Channel 1 LED
Deleting Paired Accessories:
1. Enter programming mode by holding down the channel select butt
on until the Channel 1 LED
Setting the Notification Mode:
1. The Wireless Receiver has three modes
—
Alarm & Vibrate, Vibrate, and Alarm.
Installation:
For Belt Clip
Fo
r Wall Mounting
Belt clip tab
Alarm
Vibrate
Alarm & Vibrate
Tone
Channel
select
button
1. Hold the receiver unit against the wall to get an idea of where the receiver should be installed.
2. Install 1 nail (not included) on the wall.
3. Hang the receiver on the nail.
1. Using your finger, pull the tab on the top of the receiver to reveal the
belt clip.
2. Clip the receiver to a belt.
flashes.
2. Press the channel select button to cycle through channels until the desired channel is selected.
3. Press the tone select button to cycle through ringtones until the desired ringtone is selected.
4. Trigger the accessory. Once the accessory is triggered, the receiver will beep indicating the
units have been paired. If another channel lights up, this accessory is already programmed on
the indicated channel.
Note: If pairing an accessory to a channel that is already paired with
another accessory, the original accessory will be deleted.
5. Press the channel select button to move to the next channel or exit
pairing mode.
Note: If no activity for 30 seconds the receiver will automatically exit
pairing mode.
select
button
flashes.
2. Press the channel select button to cycle through channels until the desired channel is selected.
3. Press and hold the channel select button and tone select button simultaneously until a beep is
heard. Press the channel select button to move to the next channel or exit pairing mode.
Note: The reset button is used to reset a channel after it has been triggered. It is not used to
clear any programming.
2. When the switch is flipped to Alarm, the receiver’s built-in speaker will sound.
3. When the switch is flipped to Vibrate, the receiver will vibrate only and there will be no sound.
4. When the switch is flipped to Alarm & Vibrate, the receiver’s built-in speaker will sound and vibrate.
SECO-LARM U.S.A., Inc. 3
CBA Wireless Vibrating Receiver
Replacing the Batteries:
Also Available from SECO
-
LARM:
1. Remove the battery cover.
Battery
Battery cov
er
Wireless
NOTICE
:
However, the
to
Trademarks
s material may not be reproduced or copied, in whole or
LIMITED
WARRANTY:
LARM product is warranted against defects in material and workmanship while
to
This Warranty
is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
LARM determines that such
The sole
d the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at
LARM be liable for any special, collateral, incidental, or consequential
SECO
-
LARM
FCC COMPLIANCE STATEMENT:
Wireless
Wireless
Wireless
Wireless
Wireless
2. Place 2x AA batteries (not included)
in the battery compartment, making
sure to observe correct polarity.
3. Replace the cover.
compartment
Alert System
RA-4961-K1Q
Outdoor PIR Sensor
RA-4961-DSQ
Magnetic Contact
RA-4961-MCQ
Pushbutton
RA-4961-PBQ
Indoor PIR Sensor
RA-4961-PRQ
Mailbox/Tilt Sensor
RA-4961-MBQ
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION. Notice: The changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure
compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited
the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECOequipment is not operating properly as a result of causes other than defects in material and workmanship.
obligation of SECO-LARM an
SECO-LARM’s option. In no event shall SECOpersonal or property damage of any kind to the purchaser or anyone else.
This SECO-
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LRM reserves the right
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
are the property of SECO-LARM USA Inc. or their respective owners.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. Thi
in part, without the written permission of SECO-LARM.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
The information and specifications printed in this manual are current at the time of publication.
®
U.S.A., Inc.
MiRA-4961-VPQ_151001.doc
PIHVK1
4 SECO-LARM U.S.A., Inc.
Loading...