Seco-Larm RA-4961-MBQ User Manual

®
RA-4961-MBQ
Wireless Mailbox/Tilt Sensor
Manual
For use with RA-4961 series receivers
Wirelessly monitor mailboxes or any tilting
motion
Up to 1,000ft (305m) transmission range*
*Transmission range will vary depending on installation and operating environment.
Mounts to standard mailbox flaps or
Adhesive mount - no screws required
Adjustable sensing angle
other flat surfaces that may tilt
CBA Wireless Mailbox/Tilt Sensor
Specifications
:
Parts List:
1x
Wireless mailbox
/tilt sensor
1x Adhesive
strip
Dimensions:
Overview:
Model
n
umber
RA-
4961-MBQ
Frequen
cy 914.8MH
z
Transmission range*
Up to 1,000ft
(305m)
Channels
1
Power
supply
1x
12V/23A
Battery
(included)
Current
Standby
3.5µA
Max 22mA
Estimated battery life
365 days (3 triggers/day)
Low battery indicator
Zone LED on receiver blinks contin
uously
IP rating
IP45
Operating temperature
-4
º~140º F (
-20º~60º C)
Dimensions
5"x1"x3/4" (
126x25x18
mm)
1x Battery
1x Manual
R
eset
Battery
Battery
Sensor
Side View
Front View
*Transmission range will vary depending on installation and operating environment.
5"
1"
/4"
RESET
draw
(25mm)
RESET
(126mm)
3
(18mm)
Adjustment
Compartment
Front View
Side View
Button
Compartment Screw
2 SECO-LARM U.S.A., Inc.
CBA Wireless Mailbox/Tilt Sensor
Installation:
1. Select the l
ocation where the sensor will be mounted.
The sensor should be mounted to the
P
airing
the Sensor
:
1. Follow the
pairing
instructions for the RA
-
4961-K1Q receiver
or RA
-
4961-VPQ wireless receiver
Resetting the Sensor:
1. To reset the receiver information, press the reset button on the front of the sensor.
Simple Reset
1. If a simple reset does not resolve any issues, a hard reset may be necessary.
Hard Reset
The receiver (
RA-4961Q
or RA
-
4961-VPQ
) LED will remain lit
after activation
until the
Align arrow with white
Arrow is in the trigger
Ensure a
rrow is in
underside of a mailbox flap.
2. Use the included adhesive strip to mount the sensor.
3. When the mailbox flap is in its neutral/closed position, turn the sensor adjustment until the arrow
is aligned with the white area.
4. Open the mailbox flap to the desired actuation angle and ensure that the arrow is pointing into
the red activation area.
area when sensor is in neutral
area when mailbox flap is opened
to enter pairing mode. (Refer to the RA-4961-K1Q or RA-4961-VPQ manual for further pairing instructions.)
2. Trigger the sensor for pairing by lifting the mailbox flap so that the arrow on the sensor
adjustment moves out of the white area and into the red trigger area.
3. The receiver will beep once and cycle to the next channel to confirm successful pairing.
the trigger area for pairing
RA-4961-MBQ is reset.
2. After the reset button has been pressed, the sensor will not be able to send a signal for five
seconds.
2. Remove the battery from the sensor.
3. Place the battery back into the sensor while holding down the reset button for five seconds.
4. The LED on the receiver will flash five times and the sensor will be reset. Note: A hard reset will reset the pairing code and the device will need to be paired again.
SECO-LARM U.S.A., Inc. 3
CBA Wireless Mailbox/Tilt Sensor
Installing Batteries
:
Also
Available from SECO
-
LARM:
NOTICE
:
However, the
LARM reserves the right to
marks
This material may not be reproduced or copied, in whole or
LIMITED
WARRANTY:
LARM product is warranted against defects in material and workmanship while
LARM’s obligation is limited to
This Warranty
is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
LARM determines that such
The sole
all be limited to the replacement or repair only, at
LARM be liable for any special, collateral, incidental, or consequential
SECO
-
LARM
1. Using
a screwdriver, remove the screw
from the
Battery
Compartment
Battery Compartment
Screw
RESET
Wireless
Wireless
Wireless
Wireless
Wireless
Wireless
RA-4961-DSQ
FCC COMPLIANCE STATEMENT:
FCC ID: YAHHAX
-
200
front of the sensor and remove the cover.
2. Place a 12V/23A battery (included) in the battery
compartment, making sure to observe correct polarity.
3. Replace the cover and screw.
Note: Low battery is indicated on the receiver. Refer to the RA-4961-K1Q or RA-4961-VPQ manual for more information.
Alert System
RA-4961-K1Q
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
used in normal service for one (1) year from the date of sale to the original customer. SECO­the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO­equipment is not operating properly as a result of causes other than defects in material and workmanship. obligation of SECO-LARM and the purchaser’s exclusive remedy, sh SECO-LARM’s option. In no event shall SECO­personal or property damage of any kind to the purchaser or anyone else.
Outdoor PIR Sensor
This SECO-
Magnetic Contact
RA-4961-MCQ
Pushbutton
RA-4961-PBQ
Indoor PIR Sensor
RA-4961-PRQ
Vibrating Receiver
RA-4961-VPQ
SECO-LARM policy is one of continual development and improvement. For this reason, SECO­change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Trade are the property of SECO-LARM USA Inc. or their respective owners. Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. in part, without the written permission of SECO-LARM.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
The information and specifications printed in this manual are current at the time of publication.
®
U.S.A., Inc.
MiRA-4961-MBQ_150914.doc
PIHVK1
4 SECO-LARM U.S.A., Inc.
Loading...