Seco-Larm RA-4961-DSQ User Manual

Page 1
®
RA-4961-DSQ
Wireless Outdoor PIR Sensor
Manual
Wirelessly monitor driveways, walkways
or other areas
Up to 1,000ft (305m) transmission range*
Programmable activation time
* Transmission range will vary depending on installation and operating environment.
Programmable sensing range up to
40ft (12m)
Runs on batteries for a convenient,
wireless installation
Adjustable mounting angle
Page 2
CBA Wireless Outdoor PIR Sensor
Specifications:
Parts List:
1x Wireless Outdoor PIR Sensor
4x Screws
Dimensions:
Overview:
Sensor
Battery
Photo
Test
Mounting
Model number
RA-
4961-DSQ
Frequency
914.8MHz
Transmission range*
Up to 1
,
000ft (305m)
Channels
1
Power supply
4x AA
Batteries
(Not included)
Current
Standby
70µA
Max 18mA
Estimated battery life
300 days (3 triggers/day)
Low battery indicator
Zone LED on receiver blinks continuously
PIR sensor range
13' (4m) / 23' (7m) / 26' (8m) / 39'
(12m)
PIR sensor
detection
angle
12º
(with lens cover)
/ 15º (without cover)
IP rating
IP45
Operating temperature
-4º~140º F (
-
20º~60º C)
Dimensions
37/8"x313/16"x43/4" (98
x97x120 mm)
4x
Screw anchors
1x Manual
*Transmission range will vary depending on installation and operating environment.
Lens Cover
313/16"
37/8"
23/4"
43/4"
draw
(120mm)
(97mm)
(Removable)
(98mm)
Sleep timer
compartment
Range
Sensor
Filter
button
(70mm)
Side Back (Cover removed) Front
Sunshield
base
2 SECO-LARM U.S.A., Inc.
Page 3
CBA Wireless Outdoor PIR Sensor
Installation:
1. Select the location where the sensor will be mounted.
6~9'
Programming the Sensor:
1. To access programming functions, the cover of the se
nsor
Removing the Cover
Pairing the Sensor:
Test
1. Follow
the
pairing
instructions for the
1. Use the DIP Switches to program various functions.
Programming the DIP Switches
Photo
3~6ft/s*
1.5~3ft/
c. Filter
– The detection speed of the sensor can be set for varying object speeds.
d. Photo Sensor
– When ON the sensor will be inactive during the day or when
near a bright light source.
a. Sleep Timer
– The sensor will not reactivate for the
set amount of time after the sensor is triggered.
b. Range
– The range of the sensor can be set for
varying
installation environments.
2. The sensor should be mounted 6~9 feet (2~3 meter) above ground, have
a clear view of the desired detection area, and be safe from water.
3. Use the four included mounting screws to mount the sensor to the surface.
4. Point the sensor toward the desired detection area (lens cover can be
removed to widen the detection angle).
must be removed.
2. Remove the sunshield from the sensor.
3. Using a screwdriver, remove the screws from the front of
the sensor and remove the cover.
2. Refer to the guide below for DIP switch programming.
7s*
30s
Sleep timer
(2~3m)
Range
Filter
Range
13' (4m) 23' (7m)
(0.5~1 m/s)
ON* OFF
*Default Setting
s
39' (12m)* 26' (8m)
(1~2 m/s)
Sensor
RA-4961-K1Q receiver or RA-4961-VPQ wireless receiver to enter pairing mode. (Refer to the RA-4961-K1Q or RA-4961-VPQ manual for detailed pairing instructions).
2. Press the "Test" button. This will activate the sensor for pairing.
3. The receiver will beep once and cycle to the next channel to confirm successful pairing.
SECO-LARM U.S.A., Inc. 3
button
Page 4
CBA Wireless Outdoor PIR Sensor
Installing Batteries:
Also Available from SECO
-
LARM:
1. Remove the sunshield from the sensor.
Using a screwdriver, remove the screws from the front
Battery
compartment
Wireless
Wireless
Wireless
Wireless
Wireless
Wireless
FCC COMPLIANCE STA
TEMENT:
FCC ID: YAHDWS
-
100
NOTICE
:
However, the
LARM reserves the right to
Trademarks
e reproduced or copied, in whole or
LIMITED
WARRANTY:
LARM product is warranted against defects in material and workmanship while
LARM’s obligation is limited to
This Warranty
cal or electrical misuse or abuse, neglect, repair or
LARM determines that such
The sole
LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at
nsequential
SECO
-
LARM
2.
of the sensor and remove the cover.
3. Place 4x AA batteries (not included) in the battery
compartment, making sure to observe correct polarity.
4. Replace the cover and screws.
5. Replace the sunshield.
Note: Low battery is indicated on the receiver. Refer to the RA-4961-K1Q or RA-4961-VPQ for more information.
Alert System
RA-4961-K1Q
Vibrating Receiver
RA-4961-VPQ
Magnetic Contact
RA-4961-MCQ
Pushbutton
RA-4961-PBQ
Indoor PIR Sensor
RA-4961-PRQ
Mailbox/Tilt Sensor
RA-4961-MBQ
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
used in normal service for one (1) year from the date of sale to the original customer. SECO­the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. is void if damage is caused by or attributed to acts of God, physi alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO­equipment is not operating properly as a result of causes other than defects in material and workmanship. obligation of SECO SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or co personal or property damage of any kind to the purchaser or anyone else.
SECO-LARM policy is one of continual development and improvement. For this reason, SECO­change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. are the property of SECO-LARM USA Inc. or their respective owners. Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not b in part, without the written permission of SECO-LARM.
-
The information and specifications printed in this manual are current at the time of publication.
This SECO-
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
MiRA-4961-DSQ_150916.doc
4 SECO-LARM U.S.A., Inc.
PIHVK1
Loading...