Seco-Larm E-931-S33PRGQ User Manual

E-931-S33PRGQ

33ft Polarized Reflective Photoelectric

Beam Sensor

Manual

 Polarized sensor is immune to
 shiny objects: Triggers only when
 correctly reflected light is detected.
 Weatherproof (IP55)
 Anti-condensation housing

 12-30V DC/AC 60Hz, 100mA

 Up to 33ft (10m) sensing range
 Round reflector, Dia.: 3

1

/4"

 Form C relay: 0.5A@30VAC/VDC
 Beam status LED
 N.C. Tamper switch:

500mA@30VAC/VDC

Caution:

 This sensor is not designed to prevent bodily injury or loss of life.
 This sensor is not designed for use in environments where explosive gasses may be present.
 Use of this sensor in certain security applications may be regulated by local laws or codes. SECO-LARM is not

responsible for compliance with such laws or codes.

ENFORCER 33ft Polarized Reflective Photoelectric Beam Sensor

Specifications:

Model

E-931-S33PRGQ

Type

Polarized reflective

photoelectric beam sensor

Sensing range

33ft (10m)

Operating voltage

12-30V DC/AC 60Hz, 100mA

Current drain
Standby

55mA@12VDC

Active

40mA@12VDC

Response time

10ms (max.)

Light source

IR LED/Wavelength 740nm

LED
Solid Green

Good beam signal, properly aligned

Alternating flash

Poor beam signal

Solid Red

No beam signal, triggered

Trigger output

SPDT Relay output (NO/NC/COM)

Switching capacity

500mA@30VAC/VDC

Tamper switch

N.C., 500mA@30VAC/VDC

IP Rating

IP55

Operating temperature

-4~131 F (-20~55 C)

Parts List:

1x Sensor
1x Reflector
1x Mounting bracket
1x Sensor hood
4x Cover screws
2x Mounting screws
1x Reflector mounting screw
1x Rubber ring
1x Cable connector
1x Manual
1x Removable terminal block
1x 10KΩ Resistor

Dimensions:

413/16”

(122mm)

3

/16”

(4mm)

31/4”

(82mm)

3

/8”

(9mm)

21/8”

(54mm)

23/8”

(60mm)

115/16”

(49mm)

27/16”

(62mm)

Overview:

Tamper switch

Vertical
adjustment screw

(without cover)

Cover

Cover

screw

Wire cable connector

Mounting plate
Hood

Beam

sensor LED

Terminal

block

Cable breakout

Captive screw
Beam sensor

Cable breakout

Note: Depending on the monitoring system used by the gate motor, it may be necessary to use either the N.C. output or

connect the included 10kΩ resistor to the N.O. or N.C. output. Please refer to the gate operator manual or the gate
operator manufacturer for the preferred monitoring method.

12-30V DC/AC

60Hz, 100mA
(Non-Polarity)

 Polarity does not matter for the power input.
 Connect the N.C. tamper terminal to the

tamper circuit of an alarm control panel.

Wiring Diagram:

N.C.

N.O.

COM

Tamper
N.C.

Relay

2 SECO-LARM U.S.A., Inc.

ENFORCER 33ft Polarized Reflective Photoelectric Beam Sensor

Mounting:

Alignment:

Solid green

Good beam signal,

properly aligned

Alternating flash

Poor beam signal

Solid red

No beam signal,

triggered

Wiring for the Bottom Cable Breakout

1. Unscrew the four cover screws and remove the

cover.

2. Loosen the captive screw and remove the sensor

from the mounting plate.

3. Using the included mounting screws, mount the

mounting plate to the wall.

4. Use the cable breakout and cable connector at

the bottom or rear of the sensor to run the wires.

5. Hang the sensor back on the plate and use the

captive screw to secure it in place.

6. Re-attach the cover, replace the four screws, and

attach the hood to the top of the sensor.

1. Puncture the cable breakout located at the bottom

of the sensor using a screwdriver or other object.

2. Insert the short end side of the cable connector

into the cable breakout hole and use the nut to
secure it, tightening with a wrench as needed.

3. Run the wires through the end cap and cable

connector.

4. Then screw the end cap into the external side of

the cable connector to prevent water from
entering the unit.

1. Mount the sensor and reflector so that they face

each other.

2. Connect power to the sensor. The LED will light

as indicated in the chart below.

3. Unscrew the four cover screws and remove the

cover.

4. To find the correct alignment, slowly turn the

lens assembly left and right to adjust the
horizontal angle.

5. Loosen the vertical adjustment screw to adjust

the vertical angle.

6. Place the hood on the sensor by sliding the

hood’s ridges into the slots on the sides of the
sensor.

7. Re-attach the cover, replace the four screws,

and attach the hood to the top of the sensor.

Lens

alignment

±90

±5

Horizontal

adjustment

Vertical

adjustment

Cable
Connector

End cap

Sensor

Nut

Rubber

neck

SECO-LARM U.S.A., Inc. 3

ENFORCER 33ft Polarized Reflective Photoelectric Beam Sensor

WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair,
or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal
or property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.

MI_E-931-S33PRGQ_160216.docx

PITSW3

SECO-LARM

®

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: [e-mail]

Troubleshooting:

Sensor does not detect the object.

 Change the angle of the sensor or readjust

the sensitivity setting.

The beam sensor LED will not turn green.

 Clean the sensor and reflector with a damp

(not wet) cloth.

 Adjust the reflector and/or sensor for proper

alignment.

Beam sensor LED lights when object
is detected, but there is no output.

 Check wiring between the sensor and local

alarm device.

Sample Applications:

Garage

Door

Gate

Vehicle

Detection

Assembly

Line

Other Sensors Available:

Dual and

Quad Beam

Curtain and

Barrier

Optional Accessory:

Reflector Hood

E-931ACC-HR1Q

Provides extra
protection for the
reflector.

Compatible with Reflective Photoelectric Beam Sensor models

E-931-S50RRGQ, E-931-S35RRQ, and E-931-S33PRGQ.

Reflective

Photobeam

4 SECO-LARM U.S.A., Inc.