Seco-Larm E-931ACC-CQ User Manual

Specifications:

Model Number
Type
Sensing Range
Voltage Supply
Total Current Consumption
Stand-by Current
Light Source
Ambient Temperature
Speaker Response Time
Speaker Volume
Alarm Time Range
External Chime Output
Speaker Output
Mounting Brackets

Retro-Reflective Photoelectric Entry Alert System

Sensor: 9-15 VDC, Chime: 9-15 VDC

~1 sec. for Chime, 30 sec. for Alarm

Adjustable from 0~90 dB at 1m (max.)

Chime / Off /Alarm (Select by switch)

E-931CS22RRCQ

22' (7 m)

100mA Max.

30mA

IR LED

-40~1220 F (-200~500 C)

Adjustable 3~30sec. for alarm

3.5mm TRS connector

All Included

Troubleshooting:

Trouble Remedy(s)

Sensor does not detect the object. Sensor not aligned properly.

Red LED does not turn on.

Dimensions:

23/8" (60mm)

" (71mm)

16

/

13

2

NOTICE:

the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
or in part, without the written permission of SECO-LARM.

The information and specifications printed in this manual are current at the time of publication. However,

Possible Origin(s)

1) Reflector and/or sensor is misaligned.

2) No power.

13/16" (30mm)

" (71mm)

16

/

13

2

" (63mm)

32

/

15

2

Change the angle of the sensor or

1) Adjust the reflector and/or sensor for
proper alignment

2) Check power adapter and cable.

27/16" (62mm)

23/32" (53mm)

" (52mm)

64

/

3

2

(35mm)

13

/32" (10mm)

" (63mm)

32

/

15

2

13/8"

reflector.

" (52mm)

64

/

3

2

®

ENFORCER

Sensor

Retro-Reflective Photoelectric
Sensor Entry Alert System

E-931CS22RRCQ

Range: 22ft. (7m)

INSTALLATION MANUAL

Features:

••

•

••

Retro-reflective photoelectric sensor.

••

•

••

Range: Up to 22 feet (7m).

••

•

••

Perfect for monitoring an entrance, or for counting
foot traffic with optional counter.

••

•

••

Will make “ding-dong” sound or alarm sound
when the beam is interrupted.

••

•

••

Speaker volume can be adjusted or turned off.

••

•

••

When in alarm mode, sounding time is adjustable
from 3 to 30 seconds.

Caution:

• This sensor was not designed to prevent bodily injury or loss of life.

• Use of this sensor in certain security applications may be regulated by local laws or codes.

SECO-LARM is not responsible for compliance with such laws or codes.

Included:

••

•

••

All components plug into each other.
No hard-wiring required.

••

•

••

Optional counter available (E-931ACC-CQ).

••

•

••

Optional second speaker available (E-931ACC-SQ).

••

•

••

Includes the following:
— Retro-reflective photoelectric sensor.
— Reflector.
— Speaker/electronic chime.
— Power adapter.

WARRANTY:

ENFORCER Photobeam Sensors are warranted against defects in material and workmanship while
used in normal service for a period of one (1) year from the date of sale to the original customer. Our obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.

SECO-LARM U.S.A., Inc.,

Fax: [phone] Website: www.seco-larm.com E-mail: [e-mail]

16842 Millikan Avenue, Irvine, CA 92606 Tel: [phone]

MIE931CS22RRCQZZ_081012.pmd

®

PITSW3

ENFORCER

®

E-931CS22SQ

Transmitter/Receiver

E-931ACC-R1Q

Reflector

ENFORCER

®

E-931ACC-SQ

Speaker/Electronic Chime

E-931ACC-BLS4Q

Sensor Bracket

E-931ACC-BLR1Q

Reflector bracket

Note: Products with model numbers that end with "Q" or that have a round green "Q" sticker are RoHS compliant.

Power

Adapter

Optional Accessories:

Mounting the Reflector:

Sample Fixed Mounting:

Mounting the Speaker/Electronic Chime:

Sample
Fixed
Mounting:

Sample
Bracket
Mounting:

E-931ACC-SQ

Speaker/Electronic Chime

(with 32ft wire)

E-931ACC-CQ

Digital Counter

(with 32ft wire)

E-931ACC-RC

Round Reflector

80 x 80 mm

Round/Square Reflectors

Sample Installations:

Store front door

Main

entrance

door

¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤

m

c

o

e

e

l

¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤

W

¤¤¤¤¤

¤¤¤¤¤

¤¤¤¤¤¤¤¤¤¤

Other possible applications: Offices, stores, schools, warehouse, vehicle detection, etc.

Garage

door

Wiring: (one speaker, no counter)

Wiring: (with optional counter and second speaker)

Output

Speaker (optional)

ENFORCER

®

Sensor

Up to 22' (7m)

¤¤¤¤¤¤¤

Reflector

NOTE: a) When adding a 2nd speaker, if the application distance between speakers exceeds 33 ft. (10m),

¤¤¤¤¤¤¤

then a power adaptor is required for the 2nd speaker.

b) When there are 2 devices added to the first speaker, such as a 2nd speaker & a counter,

then a second power adaptor is required for the 2nd speaker even when the distance is within 33 ft. (10m)

c) Speaker and counter use standard 3.5mm stereo jacks.

Adaptor

Input

ENFORCER

Speaker

®

Input

E-931ACC-HRQ

Reflector Hood for

¤¤¤¤¤¤¤¤¤¤

Counter (optional)

Output

Mounting the Sensor:

Installation and Adjustment:

LED Functions:

RED LED - When ON, it indicates the sensor is

powered and aligned properly.

Installation:

1. Mount the reflector and sensor so they face each
other at about 2' off the ground or knee high.

2. Connect the sensor to the speaker. If longer range is
desired, use a 3.5mm stereo audio extension cable
(not included).

NOTE: Do not cut any cables. Cutting cables will void

the warrenty.

3. Connect power adaptor to the speaker.

••

•

••

For signalling in multiple rooms, add an optional
second speaker (E-931ACC-SQ).

••

•

••

Connect an optional counter (E-931ACC-CQ) to
the speaker output (if desired).

4. To find the correct alignment, slowly adjust the
angles of the sensor and/or reflector up and down
and right and left.

NOTE: Correct alignment is achieved when the red LED

turns ON.

Set Speaker Mode:

After the sensor and reflector have been properly
installed, the next step is to set the speaker mode.

Choose between "Chime," "Alarm," or "OFF."

1.

2. If "Alarm" was chosen:

Adjusting the Speaker/Electronic Chime:

Wall mount hole

Bracket
mounting
holes

Switch

A. Set speaker to Alarm.
B. Adjust timer from 3 to 30 seconds.
C. Set speaker volume.

3. If "Chime" was chosen:
A. Set speaker to Chime.

B. Set speaker volume.

4. If "OFF" was chosen:
A. Set speaker to OFF.

B. The speaker will not sound when the beam is

broken.

Using the Optional Counter:

1. Automatically increases by "1" when sensor is
triggered.

2. Manually add "1" by pressing "+".

3. Manually subtract "1" by pressing "

4. Reset counter by pressing "RESET."

Testing:

1. Power up the sensor and speaker. The red LED
should be ON.

2. Pass object to be detected
between the sensor and
reflector. The red LED should
turn OFF and the speaker
(if connected) should sound.

Switch: Chime/

OFF/Alarm
Timer: 3~30 Sec.
Volume:0 ~ max.

-

".

®

ENFORCER

Red
LED