The information and specifications printed in this manual are current at the time of publication.
copie
d, in whole or in part, without the written permission of SECO
-
LARM.
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship while
LARM’s
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation
LARM determines that such equipment is not operating properly as a result
LARM and the
LARM’s option. In
LARM be liable for any special, collateral, incidental, or consequential personal or
prop
erty damage of any kind to the purchaser or anyone else.
SECO
-
LARM
®
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800 Email: sales@seco
-
larm.com
IMPORTANT
:
statutes.
NOTE:
While the system can provide valuable protection to home and property when properly installed, it
s or
PIHLK1
MiE-921APQ_141029.docx
loss and uses flash memory
Models Available
Certification
Make sure that you have entered the correct PIN
Number. Try re-entering it.
Auto dialer will not arm/disarm
• While pressing and holding the [PROG] button, use a
pen or paper clip to press the [RESET] button on the
back of the dialer. This sets the PIN number to the
default (000).Then try to arm/disarm again.
Make sure that the telephone line is working.
• Make sure that you have programmed at least one
Auto dialer will not dial out
telephone number into the unit and that the full
number has been stored.
•Make sure that the system is in Auto Dial mode.
Check to see if another unit (fax or answering
machine) could be answering the call and remove the
Unit doesn’t respond to a call-back
other unit.
• Adjust the call-in ring detect setting so that the auto
dialer will answer.
Difficulty in activating ‘room monitor’
by telephone remote control
Try pressing the code key again.
• Move to a quieter location as ambient noise may
affect the auto dialer’s ability to detect the tone signal.
cannot guarantee complete protection against intrusion. SECO-LARM is not responsible for any losse
damage which may occur during the use of this product.
Users and installers of this product are responsible for ensuring this product complies with all
national, state, and local laws and statutes related to monitoring and recording audio and video signals.
SECO-LARM will not be held responsible for the use of this product in violation of any current laws or
Auto Dialer
Manual
used in normal service for one (1) year from the date of sale to the original customer. SECO-
prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical
or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation,
or if for any other reason SECOof causes other than defects in material and workmanship. The sole obligation of SECOpurchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECOno event shall SECO-
When triggered by an alarm system, the ENFORCER Auto Dialer can call up to 5 numbers. Each
number can contain up to 32 digits, including #, tones, and pauses. The LCD shows the number being
dialed at each stage of the dialing process. The receiver can then listen in to sounds in the room and
disarm the system. The same functions are available by remote call in as well as arming the system.
The dialer includes a home mode (acting like a door chime when the owner is present) and a panic
button. The 105dB built-in siren alarm can be programmed on or off. It also allows for the option of a
backup battery (not included) to continue offering protection during a power
to protect against system data loss in case of extended power failure.
Page 2
ENFORCER Auto Dialer
Features:
•
Table of Contents:
Features
................................
.........................
2
Setting the Date and Time
..........................
9
Summary Programming/Operation Chart:
Current PIN
[PROG]
[ARM/DISARM]
New PIN
[ARM/DISARM]
[PROG] x9
[PROG]
[#/DOWN] or
Enter Phone
[PROG]
[PROG]
[#/DOWN] or
[PROG]
PIN [PROG] x4
[ARM/DISARM]
[#/DOWN] or [*/UP]
[ARM/DISARM]
[PROG] x6
PIN [PROG] x5
[ARM/DISARM]
[#/DOWN] or [*/UP]
[ARM/DISARM]
[PROG] x5
PIN [PROG] x6
[ARM/DISARM]
[#/DOWN] or [*/UP]
[ARM/DISARM]
[PROG] x4
PIN [PROG] x7
[ARM/DISARM]
[#/DOWN] or
[*/UP] [ARM/DISARM]
[PROG] x3
PIN [PROG] x8
[ARM/DISARM]
[#/DOWN] or [*/UP]
[ARM/DISARM]
[PROG] x2
[PROG]
[#/DOWN] or
Repeat for each
[PROG]
(In Standby Mode)
Press and Hold [PROG]
[#/DOWN] or [*/UP]
Check to see if number is dialed
PIN [ARM/DISARM]
Receive Call
Press Key Code on Telephone Keypad
Dial Voice Dialer Number
Press Key Code on Telephone Keypad
(In Standby Mode)
[HOME]
Last 5 Sensor Trigger Records
(In Standby Mode)
[#/DOWN]
Stored
Emergency Telephone Numbers
(In Standby Mode)
[*UP]
Parts List ......................................................... 3
• Built-in auxiliary output for external alarm or siren
®
........ 13
1. Setting/Changing PIN Number (see pg. 6)
2. Setting Emergency Phone Numbers (see pgs. 6~7)
PIN
x2
[ARM/DISARM]
[*/UP]
3. Deleting a Stored Phone Number (see pg. 7)
PIN
x2
[ARM/DISARM]
[*/UP]
[DELETE/PAUSE] [ARM/DISARM]
4. Setting the Siren Function (see pg. 7)
5. Setting the Auto Dial Function (see pg. 8)
6. Setting the Number of Auto Dial Cycles (see pg. 8)
7. Setting the Number of Call-in Rings (see pg. 8)
8. Setting the Entry Delay Time (see pg. 9)
9. Setting the Date/Time (see pg. 9)
PIN
x9
[ARM/DISARM]
[*/UP]
10. Test Auto Dial Function (see pg. 9)
11. Arm/Disarm System (see pg. 10)
12. Remote Control by Telephone (see pgs. 11~12)
13. Activate/Deactivate Home Mode (see pg. 12)
14. View (see pg. 13)
ENFORCER Auto Dialer
Number
[ARM/DISARM]
[ARM/DISARM]
position
x8
x8
x2
2SECO-LARM U.S.A., Inc.
SECO-LARM U.S.A., Inc. 15
Page 3
ENFORCER Auto Dialer
Program Planner:
Program: Numbers
Date:
TELEPHONE NUMBER
2
3
4
5
For Future Use
Installation
: Triggers
Date:
TRIGGER
GENERAL DESCRIPTION
SENSOR LOCATIONS
1
2
Use these charts during setup to record phone numbers and sensor locations for future reference.
Wiring Diagram:
Trigger 1 Trigger 2
Siren
DC+
ENFORCER® Reset GRD
or
Power Adapter
lug,
+ -
External Power
+ -
SM-206Q*
E-964-D390Q*
* E-964-
D390Q Photobeam Detectors, SM
-
200Q
Magnetic
SECO-LARM, please visit our website at www.seco
-
larm.com
.
SM-200Q*
Operating voltage
9~12 VDC
Standby
5mA Dialing
10mA Alarm On
18
0mA Programmable emergency phone numbers
5
Maximum digits per telephone number
32
Backup battery type/life (not
included)
9VDC/≈20h
Alarm sound level at 12" (30cm)
≥105dB
Trigger inputs
2 x N.C. Trigger
Trigger input timer
≥500ms
Auxiliary output current (max)
125mA
Operating temperature
32°
~104°F (0
°
~40°C)
Storage temperature
-4°~140°F (
-20°
~60°C)
Weight
6.2-oz (175g)
Dimensions
33/8"
x45/16"
x17/8" (86
x110x47
mm)
Specifications:
1x Auto dialer unit
1x
Telephone cable
1x
Remote control instruction card
1x
Dual outlet telephone jack adapter
2x Plastic wall anchors
2x Wall mount screws
1x
Wall mounting template
1x
User manual
Parts List:
It is recommended that you use a pencil during setup and redo it in ink afterwards. The user
should keep in a safe, easily accessible location and a copy should be retained by the installer.
ENFORCER Auto Dialer
NUMBER
PRIORITY
1
(include area code and dialer prefix as needed, add
PBX pause and extension if applicable, see p. 6-7)
NAME OF PARTY TO BE REACHED
Current draw
Max. (at 12VDC)
Telephone Wall Jack
Back Connection Area (Cover Removed)
External Alarm/Siren
14 SECO-LARM U.S.A., Inc.
Output+
9~12VDC
125mA Max.
COM.
Supply
(3.5mm Phone P
Not Included)
Sensors, and SM-206Q Concealed Magnetic Sensors shown as
examples only: For other sensors and products available from
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Auto Dialer
Overview:
DC Power LED
LCD Screen Layout:
Front
2015
20152015
2015
----
01
0101
01
----
01
01 01
01
12
1212
12
----
0000
0000
Siren Alarm
Auto
Dial Time/Date
Call-Back Rings
Home Mode
Activated
Left Side
Right Side
Armed or
Disarmed
LED Strobe Light
Door/Window Switches,
Voice Dialer
Shock/Vibration Detector
Tamper Switch
Photobeam Sensor
Operating the
Auto Dialer
, continued:
Low-Battery (LOW BATT.)
Indicator
Note:
In order
to avoid potential damage due to battery leakage
, d
o not leave a low battery in
View Function
Note:
After 10 seconds of inactivity, the dialer will automatically exit the
view mode and return
For a complete list
ing of SECO
-
LARM products, please visit us online at www.seco
-
larm.com.
Tips:
Also Available from SECO
-
LARM
:
ENFORCER Auto Dialer
Back (Covers Removed)
Low Battery LED
LCD Display
Numeric Keypad
Mounting Points
erminal Block
T
Reset Button
Battery Receptacle (Battery not included)
Siren Speaker
LINE Jack
DC Power Jack (for 3.5mm phone plug
adapter, not included)
Home Mode Button
When the charge level of the 9VDC backup battery (not included) is low, the “LOW BATT.” LED
will flash once every 1.5 seconds. Replace the battery in order to continue providing functionality
during a temporary disruption in power.
the unit. Also, be sure to remove the battery if the unit is unused for a period of time.
To view the last 5 sensor trigger events, while in standby mode press the [#/DOWN] button.
To view stored emergency telephone numbers, while in standby mode press the [*/UP] button.
to standby.
1. Make sure that the full telephone numbers have been stored as they would normally be dialed
from a local phone.
2. The auto dialer is only suitable for single phone lines. It is not compatible with fax machines.
3. Set the number of Call-in rings to be less than the voicemail or message answer point.
Alarm Triggered
PASSWORD
PASSWORD MEMORY
PASSWORDPASSWORD
Note: For explanation of these symbols, please see Programming the Auto Dialer on pages 6~9.
4 SECO-LARM U.S.A., Inc.
MEMORY LEARN
MEMORYMEMORY
LEARN
LEARNLEARN
CYCLE
CYCLE ENTRY
CYCLECYCLE
℡℡℡℡
TRIGGER HOME
TRIGGER HOME
TRIGGER HOMETRIGGER HOME
ENTRY
ENTRYENTRY
ARM
ARM
ARMARM
®
SL-1301-BAQ
SS-040Q
SECO-LARM U.S.A., Inc. 13
Magnetic Contacts, etc.
SS-072Q
E-921CPQ
E-931-S35RRQ
Page 5
ENFORCER Auto Dialer
Operating the
Auto Dialer
, continued:
END CALL
- Pressing [3 #]
will end the call.
Note:
If the user enters an incorrect password or key code, the dialer will sound 5
“
beeps”
Home Mode
Use
Note:
Arming the system deactivates the “Home” mode. After disarming, reactivate the
Installing the Auto Dialer:
power as long as the 9V battery is installed. The standby battery should provide about 20 hours of
use the included dual outlet telephone
Fig. 3
Fig. 2
Battery
Cover
5~6ft
Fig. 1
ENFORCER Auto Dialer
Remote Control by Telephone – Function Explanations, continued:
ARM SYSTEM – Pressing [5 #] during a user callback will arm the system, confirming with
three short “beeps,” and automatically hang up. If there are 5 rapid “beeps” after three short
“beeps,” it means a door/window is not closed. The dialer will then give 5 seconds to disarm
the system.
DISARM SYSTEM – Pressing [6 #] will disarm the system and automatically hang up.
and automatically hang up.
To turn off the alarm function and use the dialer as a door chime, set the dialer to “Home” mode. A
chime will ring any time one of the sensors is triggered.
To activate the “Home” mode:
1. Press the [HOME] button on the left side of the dialer. One chime will sound and the word
‘HOME’ will appear on the LCD screen.
2. After 60 seconds, another chime indicates that the dialer is now in the “Home” mode.
3. When a sensor is activated, the dialer will chime twice.
4. If the panic button is pressed, the dialer will sound a 30-second alarm and start the dialing
sequence to the programmed emergency numbers.
To deactivate the “Home” mode, simply press the [HOME] button again.
Note: You can program the telephone numbers and voice messages prior to connecting the
operation.
Note: The Auto Dialer uses EEPROM to retain memory in the event of a power loss.
1. Select a location for the dialer near a standard electrical
outlet (if user-supplied 12VDC adapter is to be used), a
telephone wall jack, and the alarm control panel, but out of
sight. The dialer should not be exposed to direct sunlight or
(1.5~2m
rain, and must not be mounted near heat sources such as
radiators, heating ducts, or stoves.
2. For wall-mount, use the wall mounting template to drill
holes and attach 2 screws into the wall at the desired
location. For convenience, 5~6ft (1.5~2m) above the floor
is recommended (Fig. 1).
3. Remove the cable cover and battery cover from the back of
the auto dialer (Fig. 2).
4. Install a 9VDC backup battery (not included). Reattach the
battery cover.
9VDC Battery
(not included)
5. Connect the dialer to two detectors or groups of detectors in
series using the connection terminals as shown in the wiring
diagram (see pg. 3). The dialer can also be connected to two
separate alarm control panel outputs of a separate alarm
system. If an external siren/alarm is desired, connect as shown
on the wiring diagram.
6. Power:
Cable
Cover
“Home” mode if desired.
12 SECO-LARM U.S.A., Inc.
a. If the dialer is to be powered from the alarm control panel,
connect the alarm power outputs to the terminal block (see pg. 3).
b. If using a 12VDC adapter (not included), plug the adapter into the dialer’s DC power jack.
7. Connect one end of the included telephone cable to an existing Touch-Tone line wall socket,
and the other end to the dialer’s “LINE” jack. Optionally,
jack adapter to connect an extension telephone using the telephone’s cable (not included)
(Fig. 3).
8. For wall installation, place the unit over the heads of the screws installed in step 2 (Fig. 1) and
slide down. Check that the unit is firmly attached and tighten or loosen the screws as needed.
9. Once all connections are made, the dialer is ready to be programmed.
SECO-LARM U.S.A., Inc. 5
Page 6
ENFORCER Auto Dialer
Programming
the Auto Dialer:
Example
1 –
To store a number with area code 1
-
214-555-2858 and an office extension 205
letter ‘F’ appears on the LCD screen, enter ‘205’ and press the [ARM/DISARM] button.
Note:
If the PIN number is forgotten, press and hold
the [PROG] button
and
use a pen or
Setting Emergency Phone Numbers
Note:
If needed, add a 4
-
second ‘pause’ before a PBX extension number by pressing and
s on the LCD screen,
Operating the
Auto Dialer
, continued:
Function
Press key code
Listen in
1 # End call
3 # Disarm system
6 #
Function
Press key code
Listen in
1 # Arm system
5 # Disarm system
6 #
Note:
Should the user have difficulty activating functions remotely by telephone, there may
3. FUNCTION EXPLANATIONS
ENFORCER Auto Dialer
The setup mode may only be accessed when the dialer is in standby mode. If no key is pressed
within 15 seconds, the dialer will automatically exit the setup mode.
Setting and Changing the PIN Number
1. Enter the current PIN number (factory preset PIN number is ‘000’), and press the [PROG]
button once. ‘PASSWORD’ will flash on the LCD.
2. Press the [ARM/DISARM] button to accept.
3. Enter a new PIN number (3-6 digits) followed by the [ARM/DISARM] button to confirm.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
paper clip to press the [RESET] button located under the cable cover on the back of the unit
and release. The unit will return to the factory preset PIN number (000). All other user
programmed settings except the date and time will be retained.
1. Enter the PIN number and press the [PROG] button twice or until “MEMORY” flashes on the
LCD screen.
2. Press the [ARM/DISARM] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select one of the number locations 1-5.
Remote Control by Telephone
The system can be remotely controlled and monitored through any Touch-Tone phone, including
mobile phones. The user may arm or disarm the system as well as listen in on the room.
1. REMOTE CONTROL WHEN ALARM IS ACTIVATED
When an alarm has been activated and the auto dialer dials the pre-programmed emergency
numbers, the person who answers the call will hear a single “beep" for a sensor trigger or 4
“beeps” for panic button activation and may press one of the following function codes at any
time to control the system remotely:
The user should hear a “beep” in response. If not, enter the function code again.
2. REMOTE CONTROL BY USER CALL-IN (CALL BACK)
A. Using a mobile phone or any Touch-Tone phone, dial the phone number that the auto
dialer is connected to. The auto dialer will answer and “beep” once after the number of
rings in the pre-programmed call-in ringer detect cycle (3, 5, 7, or 10 rings, see pg. 8).
B. Enter the PIN Number on the phone’s keypad. The dialer will “beep” twice if the correct
code has been entered. If a wrong code is entered, the dialer will disconnect automatically
and the user must dial in again.
C. Press one of the following function codes to control the system remotely:
Note: The 5 number locations represent the order in which the numbers will be dialed in the
case of an alarm.
4. Enter the number to store including any area codes or dialing prefixes if needed (up to 32
digits, although only the last 16 digits can be shown on the LCD display) using the keypad
followed by the [ARM/DISARM] button to accept and store the number.
holding the [DEL/PAUSE] button for 2 seconds until the letter ‘F’ appear
and then continuing with the extension number as usual. A ‘#’ or ‘*’ can also be entered by
pressing, and holding for two seconds, the [#/DOWN] or [*/UP] buttons respectively. The ‘#’
sign shows as ‘┘’ and the ‘*’ sign shows as ‘└’ on the LCD screen.
(where the PBX requires a 2-second pause before the extension): After scrolling to the desired
number location, enter ‘12145552858,’ press the [DEL/PAUSE] button for 2 seconds until the
6 SECO-LARM U.S.A., Inc.
The user should hear a “beep” in response. If not, enter the function code again.
be too much ambient noise interference. Try pressing the code key again, or move to a
quieter location as ambient noise above 68dB may affect the auto dialer’s ability to detect the
tone signal.
LISTEN IN – Pressing [1 #] allows a user to hear sound in the room for 50 seconds. A “beep”
will sound at 30 seconds to remind the user that the listen in time will soon end. Pressing [1 #]
again will reset the 50-second period, and entering any other key code will end monitoring and
perform the function. If there is no other key press, the call will disconnect at the end of the 50
seconds.
SECO-LARM U.S.A., Inc. 11
Page 7
ENFORCER Auto Dialer
Operating the
Auto Dialer
:
If the siren has been programmed to “SOUND OFF” the siren will not
the PIN number and press the [ARM/DISARM]
Note:
When the siren has been programmed to “
SOUND
OFF,” the siren will not sound
Deleting a Stored Phone Number
Programming the
Auto Dialer
, continued:
ENFORCER Auto Dialer
Arming and Disarming the System:
1. To arm the system, enter the PIN number and press the [ARM/DISARM] button.
The dialer will sound three short “beeps” and the words “ARM” will appear on the LCD screen.
After 60 seconds, there will be a single “beep” tone to indicate that exit delay time has passed
and the alarm is now fully armed.
After the delay, when the system is fully armed, if a door or window connected to the alarm is
opened, the LCD screen will flash the word “TRIGGER”. After the adjustable entry delay time
has passed, the siren will begin to sound (30 seconds on and 30 seconds off) and auto dialing
will commence according to the programmed sequence and cycle times. The call receiver will
hear a single “beep” to indicate a sensor has been triggered or 4 “beeps” to indicate the
[PANIC] button has been pressed.
and the dialing will commence silently after the delay time has passed. When the call is
answered, the receiver will hear single “beep” to indicate a sensor has been triggered or 4
“beeps” to indicate the [PANIC] button has been pressed.
Note: If the auto dialer is not connected to a working telephone line, the dialer will “beep”
4 times and the siren will begin to sound without attempting to continue dialing out (this
overrides the “SOUND OFF” setting).
2. To disarm the system, enter the PIN number and press the [ARM/DISARM] button.
The dialer will sound a long “beep” and the word “ARM” will disappear from the LCD screen.
Panic Button Use
1. When the [PANIC] button is pressed, the siren will sound immediately and auto dialing will
commence without delay.
sound, but silent dialing will commence.
Example 2 – To store a number with area code 1-949-555-1234, and an office extension #200
(where the PBX requires a 2-second pause before the extension): After scrolling to the desired
number location, enter ‘19495551234,’ press the [DEL/PAUSE] button for 2 seconds until the
letter ‘F’ appears on the LCD screen, press the [#/DOWN] button for 2 seconds until the ‘┘’
appears on the LCD screen, enter ‘200,’ and press the [ARM/DISARM] button.
Example 3 – To store a local number 555-2858: After scrolling to the desired number location,
enter ‘5552858’ and press the [ARM/DISARM] button.
5. Repeat for the other numbers to be stored (up to 5 total).
6. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Note: If the dialer is programmed to call a voice pager service which requires operator assistance, the
service should be notified in advance regarding the meaning of the message. Consult local authorities
concerning the permissibility of automatically dialing their emergency numbers before programming.
1. Enter the PIN number and press the [PROG] button twice or until “MEMORY” flashes on the
LCD screen.
2. Press the [ARM/DISARM] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select the number you wish to delete.
4. Press the [DEL/PAUSE] button to delete the number.
5. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Learn
This function is unused.
Setting the Siren Function
2. To cancel the alarm and stop auto dialing, enter
button. The dialer is now disarmed.
10 SECO-LARM U.S.A., Inc.
This setting allows the user to choose between an audible alarm when triggered, or a ‘silent alarm’
while dialing the emergency numbers. The factory default is “ON”.
1. Enter the PIN number and press the [PROG] button four times or until the alarm icon
() flashes on the LCD screen.
2. Press the [ARM/DISARM] button to accept. The dialer will “beep” once.
3. Press the [#/DOWN] or [*/UP] button to select either “SOUND ON” or “SOUND OFF” and press
the [ARM/DISARM] button to accept.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
SECO-LARM U.S.A., Inc. 7
Page 8
ENFORCER Auto Dialer
Note:
Setting the Auto Dial Function
Programming the
Auto Dialer
, continued:
Setting the Number of Auto Dial Cycles
Setting the Entry Delay Time
Programming the
Auto Dialer
, continued:
Testing the Auto Dial Function
:
To test the auto dial function, while in standby mode, press and hold the [PROG] button for at least
Resetting the Auto Dialer:
ENFORCER Auto Dialer
The user can choose whether or not the dialer will dial the emergency numbers when triggered.
The factory default is “ON”.
1. Enter the PIN number and press the [PROG] button five times or until the phone icon (℡℡℡℡)
flashes on the LCD screen.
2. Press the [ARM/DISARM] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select either “ON” or “OFF” and press the
[ARM/DISARM] button to accept. The dialer will “beep” once.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
1. When the dialer is in standby mode and the (℡℡℡℡) icon is ON, the auto dial is disabled.
2. When the dialer is in standby mode and the (℡℡℡℡) icon is OFF, the auto dial is enabled.
This can be set from 1~5 cycles. The factory default is 1 cycle, meaning that the auto dialer will
dial each programmed number 1 time.
1. Enter the PIN number and press the [PROG] button six times or until “CYCLE” flashes on the
LCD screen.
2. Press the [ARM/DISARM] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select your choice of 1-5 cycles and press the
[ARM/DISARM] button to accept. The dialer will “beep” once.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
This allows the user to set the length of time before the alarm will sound, to allow time to disable
the alarm after normal entry. The factory default is 20 seconds, but can be user programmed for 0,
5, 10, 15, or 20 seconds.
1. Enter the PIN number and press the [PROG] button eight times or until “ENTRY” flashes on
the LCD screen.
2. Press the [ARM/DISARM] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select 0, 5, 10, 15, or 20 seconds and press the
[ARM/DISARM] button to accept. The dialer will “beep” once.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Setting the Date and Time
1. Enter the PIN number and press the [PROG] button nine times or until the clock icon (
flashes on the LCD screen.
2. Press the [ARM/DISARM] button to accept.
3. The date and time will appear on the LCD screen as 5 sets of numbers representing the year,
month, date, hour, and minute respectively. The first set of numbers (year) will be flashing,
indicating that this can now be changed.
4. Press the [#/DOWN] or [*/UP] button to select the correct number for the year and press the
[ARM/DISARM] button to accept and move to the next position. Repeat for each position until
complete.
5. Press the [PROG] button until the programming icons disappear to exit the setup mode.
Note: Time is shown using a 24 hour clock.
)
Setting the Number of Call-in Rings
This sets the number of call-in rings after which the auto dialer will answer. The factory default is
5 rings, but can be user programmed for 3, 5, 7, or 10 rings.
1. Enter the PIN number and press the [PROG] button seven times or until the bell icon ()
flashes on the LCD screen.
2. Press the [ARM/DISARM] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select 3, 5, 7, or 10 and press the [ARM/DISARM]
button to accept. The dialer will “beep” once.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
8 SECO-LARM U.S.A., Inc.
two seconds. When you hear a ‘beep’ tone, enter the memory location (1~5) of the number you
wish to test. The auto dialer should then dial the chosen number.
To reset the Auto Dialer, press and hold the [PROG] button and use a pen or paper clip to press
the [RESET] button located under the cable cover on the back of the unit and release. The unit will
return to the factory preset PIN number (000). All other user programmed settings except the date
and time will be retained.
SECO-LARM U.S.A., Inc. 9
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.