Seco-Larm E-37EV Specsheet

piE-37EV_1209.docx

16842 Millikan Ave  Irvine, CA 92606

Tel: [phone]  Fax: [phone]
[e-mail]  www.seco-larm.com

Copyright 2012 © SECO-LARM U.S.A, Inc. All rights reserved.
The SECO-LARM policy is one of continual development. For that reason, SECO-LARM reserves the
right to change prices and specifications without notice. SECO-LARM is not responsible for misprints.

E-37EV

Alarm Pager System

 Monitors up to three zones per premises or vehicle, plus

manual paging

 Connect to nearly any type of burglar alarm control panel,

vehicle alarm, communications panel, etc.

 One positive and two negative instant trigger inputs
 Range: Up to one half mile (4W output)
 Over two million possible coding combinations
 Belt-clip receiver included
 Code-learning receiver learns up to three transmitters
 Color LEDs (Green, Orange, or Red) on the receiver

indicate which zone of the premises or vehicle was
triggered

 Audible or vibrating page indicator
 EEPROM memory stores codes for up to one year

without power

 Stores the last six pages for easy recall
 Unattended page indicator
 Low battery indicator
 Receiver uses two AAA batteries (not included)
 Extra vibrating receiver available (E-37RV)
 Connect to a CB antenna, car AM radio antenna

(adapter cable included), or external antenna
(E-37ANT)

E-37ANT

 Antenna plugs into the back

of the transmitter for use
where no existing AM or CB
antenna is available, or
where an existing antenna
might be vandalized

Features:

Available Accessories:
Specifications:

E-37RV

 Spare receiver for E-37EV,

with built-in audible or vibrating
function for silent paging

# of codes

Over 2 million (factory pre-set)

Power

12VDC

RF output power

4W max.

Current
drain

Standby

10mA

Active

1A

Frequency

27MHz

Antenna impedance

50 Ω

Range

Up to 1/2 mile in open air

1

Dimensions

41/8”x31/8”x15/16” (105x79x33 mm)

Weight

5.1-oz (145g)

1

Actual range may vary depending on the environment, installation, and/or antenna.

Transmitter

# of codes

Learns up to 3 transmitter codes

Power

3VDC (2 AAA batteries)2

Battery life

Approx. 1 month3

Current
drain

Standby

1mA

Active (Beep)

20mA

Active (Vibrate)

50mA

Dimensions

3”x21/8”x5/8” (76x54x16 mm)

Weight

1.6-oz (45g) (without battery)

2

Batteries not included

3

Based on 5 transmissions/day

Receiver

Note: Antenna required. Antenna not included.

piE-37EV_1209.docx

16842 Millikan Ave  Irvine, CA 92606

Tel: [phone]  Fax: [phone]
[e-mail]  www.seco-larm.com

Copyright 2012 © SECO-LARM U.S.A, Inc. All rights reserved.
The SECO-LARM policy is one of continual development. For that reason, SECO-LARM reserves the
right to change prices and specifications without notice. SECO-LARM is not responsible for misprints.

Purple

Blue

Green

Black

Red

Software Features:

Model

E-37EV

Trigger Indication

Colored LEDs and beeps

Transmitter Indication

‘PAGE’ LED flashes Red, Green or Orange

Positive Trigger Input

LED Indicator

'ZONE' LED flashes Green

Audible Indicator

Beeps in groups of 9 for 1 minute

Vibration Indicator

Vibrates in groups of 9 for 1 minute

Negative Trigger Input 1

LED Indicator

'ZONE' LED flashes Red

Audible Indicator

Beeps in groups of 9 for 1 minute

Vibration Indicator

Vibrates in groups of 9 for 1 minute

Negative Trigger Input 2

LED Indicator

'ZONE' LED flashes Orange

Audible Indicator

Beeps in groups of 9 for 1 minute

Vibration Indicator

Vibrates in groups of 9 for 1 minute

Manual Page

LED Indicator

'ZONE' LED flashes Green

Audible Indicator

Beeps in 3 groups of 3 for 1 minute

Vibration Indicator

Vibrates in 3 groups of 3 for 1 minute

Power ON

LED Indicator

'ZONE' LED will not be lit

Audible Indicator

Beeps in 3 groups of 3 for 1 minute

Vibration Indicator

Vibrates in 3 groups of 3 for 1 minute

Low Battery Indicator

Beep/vibrate twice every 60 seconds or when switch is pushed

Memory Indicator

Three continuous beeps/vibrates if no signals or at the end of all signals

Beep/vibrate if the signal is an alarm page, will not beep/vibrate for manual page

Unattended Page Indicator

Beep/vibrate once every 30 seconds after initial signal is received. Will continue

to beep until switch is pushed

Basic Wiring Diagram:

Alarm Pager System

To Constant +12V to Fuse Box

To Ground

Positive Trigger

Second Negative Trigger

First Negative Trigger

To Power Antenna (if needed)

To Radio (if needed)

Radio

Antenna

1 3 2 A B

LED

Manual Page

Antenna Selection

Switch