Seco-Larm DP-T100-2Q, DP-T100-1Q Installation Manual

Download

Page 1

Wireless Intercom

Features:

•

• Powered by batteries (alkaline or rechargeable)

DP-T100-2Q Wireless Intercom Starter Kit

– 2 Intercoms

DP-T100-1Q Wireless Intercom

– Single Intercom

Manual

Simple and easy setup

• Encrypted transmission offers security and protection

• Range up to 1,000ft (300m)*

• 4 Selectable channels

• Connect up to 16 wireless intercoms

• Each intercom has adjustable volume

• Indicator LEDs show mode and status

*Line-of-sight range. Actual range may vary depending on the installation and operating environment.

or power adapter (both not included)

• 4 Communication modes: full broadcast to all stations, talk on a single channel, private talk, and hands free

• Fail-safe design: if an intercom loses connection it automatically reconnects to other intercoms

Page 2

ENFORCER Wireless Intercom

Power

12VDC

/500mA

adapter

(2.1mm)

or 1.5V AA

alkaline/rechargeable batteries x 4

Low battery voltage

4.2VDC

Frequency

902~928

MHz (frequency hopping)

Number of channels

Maximum

RF Power

57.2mW

Range

1,000'

(300m)

Dimensions

71/2"x31/2"x11/4" (190x89x32 mm)

Weight

5.3-oz (150g)

Table of Contents:

Introduction

................................

Introduction:

The ENFORCER Wireless

Intercom is a simple and secure way to communicat

e between multiple intercoms

31/2"

11/4" (32mm)

Specifications:

Line-of-sight range. Actual range may vary depending on the installation and operating environment.

Dimensions:

Parts List:

2x Wireless Intercom Units

1x Manual

Parts List .....................................................................................................................................2

Specifications ..............................................................................................................................2

Dimensions .................................................................................................................................2

Overview .....................................................................................................................................3

Installation Notes .........................................................................................................................3

Powering the Wireless Intercom ...................................................................................................3

Power Controls ............................................................................................................................4

Setup ..........................................................................................................................................4

Basic Controls and Modes ...........................................................................................................5

Operation: ................................................................................................................................6-7

Troubleshooting...........................................................................................................................7

Notes ..........................................................................................................................................7

Also Available..............................................................................................................................8

(up to 16 units, total) within an area of up to 1,000ft (300m).1 The wireless intercoms operate on 4 channels and can either broadcast to all intercoms or to select intercoms on the same channel.

OFF

(89mm)

71/2" (190mm)

DP-T100-2Q only. DP-T100-1Q comes with a single wireless intercom. 3Batteries and power adapter not included.

2 SECO-LARM U.S.A., Inc.

Page 3

ENFORCER Wireless Intercom

Overview:

Installation Notes:

Battery Installation

rechargeable batteries and charge

Failure to do so may result in

1. Unpack the wireless intercom and note the included parts.

Power On/Off

Antenna

Volume up

Volume down

/hibernate

Privacy button

LED

Hands-free button

/LED

Talk button

Lock button

/LED

Call button

Powering the Wireless Intercom:

The wireless intercoms may be powered by 4 AA

Power Adapter

(not included)

Fig. 3

Fig. 2

Fig. 1

Channel selector

Transmission Indicator LED

Channel indicator LEDs

Pairing button

NOTE: Intercoms can handle multiple channels communicating simultaneously without interference.

DC Jack

2. Read this manual thoroughly. A clear understanding of the manual will make installation and operation much easier.

3. Find a good location to mount or set the units (desk, wall, etc.).

4. The intercom contains no user-serviceable parts. Opening them may damage sensitive components and will void the warranty.

batteries (alkaline or rechargeable) or by a 12VDC power adapter (both not included).

1. Press and slide battery cover open (see Fig. 1).

2. Insert 4 AA batteries (not included) into the

battery compartment (see Fig. 2).

Important: To use them using a power adapter, slide the battery mode switch to the position (see Fig. 3). For alkaline batteries, you must leave the battery mode switch in the

position (default).

damage to the unit.

Battery mode switch

Plug a 12VDC power adapter into the DC jack.

SECO-LARM U.S.A., Inc. 3

Page 4

ENFORCER Wireless Intercom

Setup:

Clearing Codes

Power Controls:

Power Switch

Turn the unit on by sliding the power switch to the on position. The transmission indicator LED will flash and the channel indicator will blink to indicate the unit is searching for a signal. Once a signal is found, the channel indicator will stop blinking and the unit will click. Turn the intercom off by sliding the power switch to the off position.

Hibernate Mode

Press and hold the volume down button for 5 seconds to put the unit into hibernate mode (indicated by a beep, a single flash of the transmission indicator LED, and three flashes of the channel LEDs). During hibernate mode, the unit cannot receive calls.

Wake from Hibernate Mode

Press any key on the unit to wake it. The channel indicator will begin to blink. Once a signal is found, the channel indicator will stop blinking and the intercom will beep.

Before setting up a new system, you must clear any preexisting codes from all of the intercoms.

1. Press and release the pairing button on one of the intercoms once. The channel indicator LED will flash in sequence indicating that it is now in pairing mode.

2. Press and hold the pairing button for 5 seconds until the channel indicator LEDs turn off, the power LED flashes, and you hear a beep, indicating that preexisting codes have been cleared.

NOTE: When adding a new intercom to the system, you must first clear any preexisting codes on

the new intercom.

Setting Up a New Wireless Intercom System

1. Clear any preexisting codes from all of the intercoms as described above.

2. Press the pairing button on one of the intercoms. The channel indicator LEDs will flash in sequence. (The first intercom to enter pairing mode becomes the primary intercom.)

3. Within 60 seconds, press the pairing button on the other intercom. The channel indicator LEDs will flash in sequence. When pairing is successful, the channel indicator LEDs of both units will stop flashing.

NOTE: If a wireless intercom loses connection, it will automatically reconnect to other intercoms.

Adding a Wireless Intercom to an Existing System

1. Make sure that any preexisting codes on the new intercom are cleared.

2. Press the pairing button on any intercom that has already been paired. The channel indicator will flash in sequence on this intercom.

3. Within 60 seconds, press the pairing button on the new intercom. The channel indicator LEDs on this intercom will flash in sequence. Once pairing is complete, the channel indicator LEDs of both units will stop flashing.

4. Repeat the above steps to pair additional intercom units, up to a total of 16 intercom units.

4 SECO-LARM U.S.A., Inc.

Page 5

ENFORCER Wireless Intercom

Basic Controls and Modes:

Call Button

Press and hold the talk button to speak. The conversation will be heard by all intercom units on the

There may be some delay, resulting in clipping

channel it will no longer be able to monitor the locked unit even if the listener returns to the channel

Press the call button to ring all intercoms on the same channel (or all channels if in broadcast mode (see "Broadcast Mode" below).

Talk Button

same channel. Two units on the same channel cannot transmit at the same time. When the transmission LED ( ) is lit the talk button is inactive.

Volume Control Buttons

Press and release the volume up and volume down buttons to adjust the volume of the intercom. The intercom will beep to indicate the volume level. There are five volume levels.

Channel Selection Button

The wireless intercom supports four separate channels and a broadcast mode. To cycle between channels, simply press the channel button ( ). The channel indicator LEDs show the currently active channel (1, 2, 3, 4, or 1234).

The intercom is in broadcast mode when all four LEDs are lit. In this mode, the intercom can receive messages from all channels and can transmit messages to all channels. Note that privacy mode cannot be activated in broadcast mode and any messages received in broadcast mode will not be private even if the sending unit has privacy mode set (see "Privacy Mode" below).

Hands-free Button

Press the hands-free button ( ) to enter hands-free mode. In this mode, intercom transmission is activated by sound without pressing the talk button. of the first sounds and this mode will not work well in areas with high background noise. Press the hands-free button again to exit this mode. Hands-free mode is also cancelled if the channel selection button is pressed.

Lock Button

Press the lock button ( ). The lock indicator LED will light and the intercom will be locked in transmitting mode. This is useful for monitoring an area. However, if a listening unit leaves that

later. Press the lock button again to unlock. NOTE: The lock button leaves the unit continuously transmitting and will tie up that channel.

Hands-free mode is sound-activated and will only transmit when sound is detected.

Low Battery Indicator

When the battery voltage is low, the power and channel LEDs will blink every 20 seconds.

Privacy Button

When either unit has privacy mode set and neither are in broadcast mode, messages between them will be private. Privacy mode cannot be set in broadcast mode, and calls to another unit that is in broadcast mode will not be private. For privacy, ask the receiver to leave broadcast mode.

NOTE: Any pause of 10 seconds between transmissions will break that private conversation

channel. The private conversation is only reestablished on the second transmission from the unit with privacy mode set.

SECO-LARM U.S.A., Inc. 5

Page 6

ENFORCER Wireless Intercom

Operation:

To use the ENFORCER Wireless Intercom system, it is helpful to understand a few principles.

just press the talk button and speak. All who are on that channel will hear the message and all

General Conversations

1. Press the call button once and all other units on the same channel (or all channels when in broadcast mode – see "Broadcast Mode" on pg. 5) will ring.

2. When any unit presses the talk button, a conversation is established, but note that the conversation is public to all on the same channel and all can join in.

NOTE: Selecting broadcast mode means that unit is connected to all channels. If any unit has

broadcast mode selected, that unit will send to and receive from all channels. If other units have selected specific channels, their replies will not be heard by others who are not on their channel.

Open Conversations

For a message to all on the same channel, either press the call button and wait for an answer, or

responses will be heard by all on the responders' channel.

Private Conversations

Private conversations are only established when neither unit is in broadcast mode and both are on the same channel.

NOTE: Because private conversations require an initial 'handshake' between two units, it is

recommended to first press the call button. If starting with the talk button, the first messages both ways will be public.

To initiate a private conversation:

1. To make a private call, press the privacy button ( ) once before a call. The privacy indicator LED lights to indicate you are in privacy mode. Press the call button and other intercoms on the same channel will ring. A private call is established when the talk button on another intercom is pressed within 10 seconds. The other unit's privacy LED will also light while the user presses the talk button to indicate that they are private. Note that, since the caller cannot know whether or not the receiver is in broadcast mode, if privacy is important, you should remind them to change to the single channel that you are on, and start the call again.

2. When a conversation is established in privacy mode, the channel will be locked to these two units for approximately 6 seconds after each transmission in order to retain the private conversation and prohibit a third party from joining or interrupting. During this time, the transmission LED ( ) on all other units on the same channel will remain lit to indicate that the channel is currently tied up.

3. If someone waits more than 10 seconds to press the talk button, their reply will not be private and will go to all on the same channel, but if you press talk within 10 seconds of hearing their message, a private conversation will be established with that unit after your initial reply.

6 SECO-LARM U.S.A., Inc.

Page 7

ENFORCER Wireless Intercom

Operation (Continued):

Notes:

Channel indicator LEDs do not stop flashing

•

Channel indicator LEDs

do not stop flashing

•

Troubleshooting:

To answer a call that you wish to be private:

talk within 10 seconds

1. If you activate the privacy mode (or have already activated it) and press of hearing a call ring, a private conversation is established with the caller after the first return message from the other unit.

2. During an existing conversation, activation of the privacy mode will take effect after one more round of messages, making all subsequent messages private.

3. Alternatively, if you are not in privacy mode and receive a call which you wish to make private, you may press the privacy button at any point. However, because this requires a "handshake" between the two units, note that this will only take effect on the second transmission. Press the "privacy" button again to exit this mode.

when pairing

when adding a new intercom to the system

Cannot receive transmissions/cannot stop transmitting

Sound is distorted or drops out

Clear preexisting codes from both intercoms.

Clear preexisting codes on the new intercom.

The lock function is activated. Exit the lock function.

• The hands-free function is active but the environment is too noisy. Turn off the hands-free function.

Shorten the distance between intercoms or adjust the

antenna.

______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________

SECO-LARM U.S.A., Inc. 7

Page 8

ENFORCER Wireless Intercom

Wireless Video Door Phone

Hands

Free Video Door Phone

Wireless Desktop

DP-236Q

DP-

234Q

SD-

862T-GWSQ

SK-910RBQ

SK-

919TP1H

BUQ SK-919TD1S

UPQ

SECO

LARM

Receivers and Transmitters also available in 2, 3, and 4 channel versions.

16842 Millikan Avenue, Irvine, CA 92606

Website:

www.seco

larm.com

Phone: (949) 261

2999 | (800) 662

0800 Email: sales@seco

larm.com

MI_DP-T100-xQ_1701006.docx

NOTICE

The SECO

LARM policy is one of continual development

and improvement. For that reason, SECO

LARM

LARM is also not responsible for misprints. All trademarks

LARM U.S.A., Inc. All

WARRANTY:

This SECO

LARM product is warranted against defects in material and workmanship while

used in normal

s limited to the repair or

This Warranty is void if

r alteration,

LARM determines that such equipment

The sole obligation of

’s

LARM be liable for any special, collateral, incidental, or consequential personal or property

IMPORTANT

with all national,

will not be

FCC COMPLIANCE

STATEMENT

FCC ID: YAHINTXX1

OMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

THIS DEVICE MUST ACCEPT

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s

antenna or the

device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure

requirements and void user’s authority to operate the device.

WARNING

ual

serviceable

Also Available from

1-Channel RF Receiver

1-Button, 1-Channel Handheld

Transmitter

1-Channel RF Transmitter

RF Transmitter

state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM held responsible for the use of this product in violation of any current laws or statutes.

heat, as it could cause fire or electric shock. Do not open the case of this device as there are no fieldcomponents inside.

THIS DEVICE C CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Users and installers of this product are responsible for ensuring this product complies

Stop using this product and disconnect it from power if you see a malfunction such as smoke or unus

authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the

service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation i replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair o improper or abnormal usage, or faulty installation, or if for any other reason SECOis not operating properly as a result of causes other than defects in material and workmanship. SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM option. In no event shall SECOdamage of any kind to the purchaser or anyone else.

SECO-LARM

U.S.A., Inc.

8 SECO-LARM U.S.A., Inc.

PIHVK1

Seco-Larm DP-T100-2Q, DP-T100-1Q Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual