Seco-Larm DP-264-1C7Q Installation Manual

Page 1
DP-264-1C7Q
Hands-Free Video Door Phone
Manual
Features:
operation
Remotely and securely talk to visitors and
unlock doors, gates, etc. from the monitor
Easily connect additional monitors and an
additional camera*
Simple 2-wire connection
*Additional monitors and camera sold separately.
Up to
2
Cameras
Built-in microphone Adjustable color tone, brightness, speaker,
and ringer volume
Camera and monitor turn off automatically
when not in use
Soft-touch button operation
®
Up to
3
Monitors
Page 2
ENFORCER Hands-Free Video Door Phone
Table of Contents
1x Hands
-
free monitor
1x Hands
-
free monitor
1x
Monitor bracket
1x Monitor bracket
1x AC Power adapter
1x AC Power adapter
1x Camera
2x Screws
1x Camera
bracket
2x Screw anchors
6x Screws
4x Wire connectors (2
-
wire) 6x Screw anchors
2x Camera
hex screws
6x Wire connectors
1x Wire conne
ctor
1x Diode
1x MOV 1x Hex wrench
1x Camera
1x Camera
bracket
4x S
crews
4x
Screw anchors
2x Camera
hex screws
2x
Wire connectors
1x Wire connector
1x Diode 1x MOV 1x Hex wrench
Note: The distance between the camera and the
CMOS
1/3" CMOS sensor
Resolution
700 TV l
ines
Lens 2.1mm
3A@30
VDC max.
Operating
Weight
1-
lb, 6-oz (750g)
Current draw
15
0mA
47/16"x53/8"x21/16"
Monitor
Display
7" Color
TFT
Operating voltage
18
VDC Relock delay
5
seconds
E-
lock delay
1 second
Weight
1-
lb, 2-oz (560g
)
Active:
555mA
Standby:
20mA
91/2"x65/16"x1"
DP-264-M7Q
Screen image simulated.
Screen image simulated.
DP-264-CQ
Specifications ................................................ 2
Parts List ....................................................... 2
Overview ....................................................... 3
Installation Notes .......................................... 4
Installation – Primary Monitor ....................... 4
Specifications:
Camera
Type Color camera
Relay output
temperature
Dimensions
dry contact
-13°~149°F (-25°~65°C)
(112x136x52 mm)
without sunshield
Parts List:
DP-264-1C7Q
Complete Kit
Hands-Free Secondary Monitor
Installation – Additional Monitors .................. 5
Installation – Camera .................................... 5
Operating Instructions ................................... 6
Wiring Diagrams ........................................... 7
Troubleshooting ............................................ 8
Current draw
Dimensions
farthest monitor should not exceed 230ft (70m).
(241x161x25 mm)
Hands-Free Camera
(2-Wire) - power
(5-Wire) - camera
Also compatible with
DP-234Q and DP-222Q
(2-Wire) – power
(5-Wire) - camera
Also compatible with
DP-234Q and DP-222Q
2 SECO-LARM U.S.A., Inc.
Page 3
Interchangeable
HD CMOS
Camera
To primary
To locking
Front
View
Back View
Doorbell
Overview:
Monitor Unit:
Speaker
To power
To camera
To monitor
ENFORCER Hands-Free Video Door Phone
Front View
Display
Monitor Button
E-Lock 13.8V
Relay Unlock Button
Talk Button
Microphone
Back View
To bell
To additional monitor
To additional camera
Jumper
Ringtone volume adjustment
Voice volume adjustment
Chroma / Contrast adjustment
Brightness adjustment
Camera Unit:
LEDs
camera
message holder 13/4"x7/16" (44x11mm)
(with sunshield)
Speaker
button
Microphone
devices
monitor
speaker volume
(without sunshield)
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Hands-Free Video Door Phone
1. Unpack the video door phone and note the included parts.
1. The monitor must be positioned so that the image can be seen clearly and the user can operate the
Power
Additional
Monitor
Additional
Camera
Bell
Installation Notes:
2. Read this manual thoroughly before installation. A clear understanding of the manual will make installation and operation much easier.
3. Find a good location to mount the monitor and camera. Make sure there is enough 21AWG (or larger) 2-conductor wire to connect both units correctly.
4. Use only untwisted-pair wire; twisted-pair wire may cause interference.
5. Avoid mounting the camera or monitor near sources of strong electromagnetic signals or other electronic devices as they may cause interference.
6. Avoid mounting the camera in direct sunlight or exposing the camera to strong vibrations or direct rain or other moisture, which could result in damage to the camera.
7. The monitor and camera contain no user-serviceable parts. Opening may damage sensitive components and will void the warranty.
8. Do not use sharp objects to press the indoor monitor buttons
9. End-of-Line Resistor Jumper: This jumper is used to adjust video on the monitor and is located behind the monitor accessible through the plastic housing. If your installation has a single monitor, the jumper must remain on the monitor. If your installation has multiple monitors the jumper must remain in place on the monitor which is farthest from the camera but must be removed from the other
Installation – Primary Monitor:
monitor’s functions.
2. Use the mounting bracket as a template to pencil in where to drill the holes for the mounting bracket screws.
3. Drill the mounting bracket holes as needed. Drill a hole large enough to fit a minimum 21AWG 2-conductor wire, which will run through the wall from the monitor to the camera.
4. Using two of the included screws and two of the included screw anchors, attach the monitor bracket to the wall, running the cable through the large hole in the mounting bracket.
5. Run wires from the first two terminals on the left of the camera Power (+ and -) to the monitor's "CN1" plug making sure to observe polarity.
NOTE: If using only one monitor, the "Additional camera / monitor (CN2, CN2A)" plugs on the back of the monitor will not be used
6. Connect the AC power adapter’s wires into the "DC" plug on the back of the monitor, making sure to observe polarity.
Connection Points
Monitor mounting bracket
CN3
+
-
Camera
1 2
CN1
+
-
Monitor
1 2
CN1A
CN2
Jumper
CN5
1
2
1 2
1
+
2
-
CN2A
4 SECO-LARM U.S.A., Inc.
Page 5
ENFORCER Hands-Free Video Door Phone
1. Position the camera so the area to be monitored is easily
If using a secondary monitor:
5ft
the wall.
NC
COM NO
Connecting to DP
-
264-M7Q
Installation – Additional Monitor:
(not included)
1. Install the second monitor in the same way as the primary monitor (see pg. 4).
2. DP-264-M7Q: Run wire from the primary monitor’s "CN1A" plug to the secondary monitor’s "CN1" plug, making sure to observe polarity. Don't forget to adjust End-of-Line jumper
CN1A
CN1
accordingly. Please refer to pg. 4.
Installation – Camera:
visible, typically 5ft (150cm) above the ground. Do not position the camera in direct sunlight, or where it will be exposed directly to rain or snow.
2. Cut a hole large enough to run the minimum 21AWG 2-conductor wire through the wall to where the camera unit is to be mounted. If using a locking device, the wires used to control the device must also be run through this hole.
3. Run the 2-conductor wire from the camera location to where the primary monitor is mounted.
Note: The distance between the camera and farthest monitor should not exceed 230ft (70m). If two cameras, measure from the farthest camera to the farthest
Camera Mounting Bracket
monitor.
4. Using four of the included screws and four of the included screw anchors, attach the camera mounting bracket to the wall.
Use these
holes to secure
the bracket to
5. Run wires from the first two terminals on the left of the camera (+ and -) to the monitor's "CN 1" plug making sure to observe polarity.
6. If the color video door phone will be used to operate an electronic door strike or electromagnetic lock, connect the wires coming from the strike or lock to the relay connections on the back of the camera. See the diagrams
Connection points and
speaker adjustment
on pg. 7.
7. Plug the AC power adapter into a 120VAC socket.
8. Test the monitor and camera unit by pressing the doorbell
Volume Power
button on the camera. The image in front of the camera should be displayed clearly.
9. To adjust the camera speaker volume, turn the potentiometer on the back of the camera clockwise or counterclockwise.
10. Push the tab on top of the bracket into the top of the camera. Make sure that no wires are pinched preventing the camera from sealing properly in the bracket.
11. Secure the camera to the mounting bracket with the included camera hex screws.
SECO-LARM U.S.A., Inc. 5
(150cm)
E Lock
-
+
Adjust the camera’s speaker volume by turning the potentiometer on the back of the unit.
Page 6
ENFORCER Hands-Free Video Door Phone
2. Press the
Talk button
on the monitor to hear audio and to talk through the ca
mera unit.
1. When the
Doorbell
button on the camera is
pressed, the monitor will ring. After ringing, any
3. If the video door phone’s relay is connected to an electric door strike or other locking device, press the
4. To see what is going on at the entrance, press the Monitor
Button once to
turn
on the monitor
.
The
Operating Instructions:
connected monitors will switch on.
Relay Unlock Button to allow entrance. If a fail-secure locking device is connected to the E-Lock pressing the E-Lock Button will allow access. See the wiring diagram on pg. 7 for more details.
Note: The lock will only remain unlocked for 5 seconds and the E-Lock for 1 second after which the camera and monitor will turn off.
camera LED and monitor will automatically switch on but there will be no audio communication in this mode. To listen in, press the Talk Button to allow 2-way audio communication. When finished, simply press the Monitor Button again and the camera will switch off. If the Talk Button is not pressed again, the monitor and camera will switch off after 30s.
6 SECO-LARM U.S.A., Inc.
Page 7
ENFORCER Hands-Free Video Door Phone
Power
-
2
1
-
CN2A
Additional
Monitor
Additional
Camera
Bell
-
Power
-
2
1
-
CN2A
Additional
Monitor
Additional
Camera
Bell
-
Wiring a Secondary Monitor and Electric Door Strike
Electric Door
Fail-S
ecure
SECO-LARM
®
®
Dry Contact
Power Supply
Magl
ock
N/C and COM
Fail-Safe
Plug
-
in Harness Connections
:
NC
COM NO
NC
COM NO
Power
2
1
-
2
CN2A
Additional
Monitor
Additional
Camera
Bell
1 2
-
Power
2
1
-
CN2A
Additional
Monitor
Additional
Camera
Bell
-
E Lock
NC
COM
NO
-
E Lock
NC
COM NO
Power
-
2
1
-
CN2A
Additional
Monitor
Additional
Camera
Bell
-
Plug
-
in Harness Connections
Third Monitor:
EOL
EOL resistor
Wiring Diagrams:
NOTE: The distance between the camera and the farthest monitor should not exceed 230ft (70m).
The EOL jumper must remain in place on the monitor which is farthest from the camera but must be removed from the other monitors.
Monitor
Power Supply
Additional Monitor
CN3
Camera
2
CN1
CN3
Camera
2
CN1
+
-
Monitor
+
CN1A
+
Monitor
+
CN1A
Camera
Monitor
1 2
Monitor
1 2
1
1 2
CN2
Jumper
1
1 2
CN2
Jumper
SECO-LARM
Release (13.8V)
E-Lock Terminals
CN5
Additional Monitor
CN3
+
CN5
1
Volume Power
E Lock
+
Camera
-
-
Camera
Monitor
1
+
2
CN5
1
+
2
2
CN1
+
1
CN1A
CN3
Camera
2
CN1
1
+
2
CN2
Jumper
Second Monitor
1
+
Monitor
1
1
+
2
2
CN1A
CN2
Jumper
Volume Power
Bell
CN5
Third Monitor
CN5
1
+
2
CN3
Camera
2
CN1
+
+
Monitor
1 2
CN1A
Additional Camera
E Lock
+
CN5
1
1
1
+
2
2
CN2
Jumper
-
resistor
-
Volume
Power
+
Camera
Volume
Power
+
Additional Camera
SECO-LARM U.S.A., Inc. 7
Page 8
ENFORCER Hands-Free Video Door Phone
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
LARM reserves the right to
isprints. All trademarks are the property of
defects in material and workmanship while used in normal service for
M’s obligation is limited to the repair or replacement of any defective
LARM. This Warranty is void if damage is caused by or attributed to acts of God,
eglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason
ip.
LARM’s
age of any kind
h all national, state, and local laws and
f this product in
S DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
THIS DEVICE MUST ACCEPT ANY INTERFERENCE
hority to operate
nge to the antenna or the device is permitted.
equirements and void user’s authority to
 Check End
-of-
Line resistor
jumper is adjusted correctly on all monitor
Troubleshooting:
Check that the camera is powered up. Check that the power supply’s polarity is correct.
The screen is blank.
Check that the monitor is powered up. Check that the video cable connecting the camera to the monitor is
The screen image is dim.
connected properly.
Check that the wiring distance does not exceed 230ft (70m)
Clean the lens using a soft, clean cloth. Check that the light source is adequate
Adjust the monitor’s color tone.
The screen image has poor color tone or flickers
Adjust the monitor’s brightness. Change the position of the camera. Use untwisted wire and make sure the wiring distance does not
exceed 230ft (70m)
Change the position of the camera.
The screen image is distorted.
The camera case is hot.
LEDs do not turn on.
Use untwisted wire and make sure the wiring distance does not
exceed 230ft (70m)
Check that the correct power supply is in use.
Check that the correct power supply is in use (18VDC). Check that the wiring distance does not exceed 230ft (70m)
Lock button does not operate the relay
Check that the correct power supply is in use (18VDC). Check that the wiring distance does not exceed 230ft (70m)
California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to
cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies wit statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use o violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THI (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s aut the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no cha Any change to the antenna or the device could result in the device exceeding the RF exposure r operate the device.
WARRANTY: This SECO-LARM product is warranted against one (1) year from the date of sale to the original customer. SECO-LAR part if the unit is returned, transportation prepaid, to SECO­physical or electrical misuse or abuse, n SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmansh The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO­option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property dam to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO­change specifications without notice. SECO-LARM is also not responsible for m SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., Inc. All rights reserved.
®
SECO-LARM
U.S.A., Inc.
Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
MI_DP-264-1C7Q_201110.docx
8 SECO-LARM U.S.A., Inc.
PICRN4
Loading...