Page 1
®
CL
-210M
-
U3B
Q
Motorized Cabinet Lock
Manual
Features:
•
Electronically secure lockers, cabinets,
cases, and drawers
• Lock status sensor allows for monitoring
whether the lock is engaged
• Door status sensor allows for monitoring
whether the door is closed completely
• Compatible with existing keypads or readers
• Spring feature gently pushes door open
•
Fail-secure operation
• Various mounting positions
• 12~28 VAC/VDC Operating voltage
• Low current draw:
- 69mA@12/24 VDC (standby)
- 165mA@12/24 VDC (active)
• 220-lb (100kg) Holding force
• Two locking orientations
Page 2
SECO-LARM Motorized Cabinet Lock
2 SECO-LARM U.S.A., Inc.
The SECO
-
LARM Motorized Cabinet Lock provides security for lockers, cabinets, cases, and
drawers. The built-in lock and door status sensors and fail-secure operation offer additional
security. The Motorized Cabinet Lock's small size and compatibility with existing keypads or
readers allow for various installations.
1x Lock body
1x
Rosette
1x 5-
Pin connector
5x Crimp
connectors
4x
Long wood screws
2x
Short wood screws
1x M
anual
Operation Fail-Secure
Operating voltage 12~28 VAC/VDC
Current
draw
Standby 69mA@12/24 VDC
Active 165mA@12/24 VDC
Lock status output 1A@125VAC
Door status output 1A@125VAC
Holding force 220-lb (100kg)
Relock time delay 2~5 seconds
Case
Polyamide
Operating humidity 0~95% non-condensing
Operating temperature 14°~113° F (-10°~45° C)
Dimensions
Lock body 23/8"x23/8"x7/8" (60x60x22 mm)
Rosette
13
/16"x23/8"x11/16" (20x60x27 mm)
Weight 3-oz (93g)
Specifications:
Overview:
Introduction:
Parts List:
Lock body
Rosette
Top view
Side view
Front view
7
/8"
(22mm)
23/8"
(60mm)
1
/2"
(13mm)
Front view
Door status
sensor
1
/4"
(7mm)
11/16"
(27mm)
Sensor
magnet
Spring
-
loaded
pin
17/8"
(48mm)
23/8"
(60mm)
13
/16"
(20mm)
23/8"
(
60mm
)
23/8"
(60mm)
2"
(51mm)
17/8"
(48mm)
17/8"
(48mm)
Page 3
SECO-LARM Motorized Cabinet Lock
SECO-LARM U.S.A., Inc. 3
Wiring Diagram:
Installation:
Trimpot
Gently turn the trimpot on
the back of the lock body
from left to right to adjust
the relock time delay.
N.O COM N.C
– +
2S 5S
1. Find
a suitable location for the cabinet lock. Ensure the lock body and rosette do not prevent
the drawer/door from opening and closing completely.
2. Set relock time delay. See "Relock Time Delay" below.
3. Wire the cabinet lock according to the wiring diagram below.
4. Mount the lock body using the included 4 long wood screws.
5. Apply a small piece of double-sided tape (not included) to the back of the rosette and gently
insert the pin into the receptacle on the lock body as to not lock the pin in place. Check that
the rosette is orientated correctly. See "Door Status Sensor Position" below.
6. Close the drawer/door and open again. The rosette will be attached in the correct location.
NOTE: If the pin becomes locked, trigger the relay control contact to unlock it.
7. Secure the rosette to the drawer/door using the included 2 short wood screws.
8. Test to ensure the rosette is aligned properly. Make adjustments as needed.
N.O COM N.C
–
+
2S
5S
Wire Color
Function
Yellow Bond sensor contact output (indicates locking element is in the "locked" position)
Blue Door status contact output (indicates door is closed)
Red
Red
Power
Output #1
Lock status
Output #2
Door status
Relay
control contact;
e.g., reader or switch
12~28
VAC/VDC
Yellow (N.C.)
Green (COM)
Blue (N.O.)
Door Status Sensor Position:
Relock Time Delay:
The sensor magnet on
the rosette should match
up with the sensor on
the lock body.
For installations where
the rosette faces the top
of the lock body, the
magnet and reed switch
should be adjacent.
NOTE:
Connecte
d access control devices
must set time delay an additional
3sec longer than the Motorized
Cabinet Lock's relock time delay.
Page 4
SECO-LARM Motorized Cabinet Lock
4 SECO-LARM U.S.A., Inc.
Doesn’t unlock
•
Check connection to power
• Check connection to reader, switch, etc.
Doesn't lock
•
Check connection to power
• Make sure the rosette's pin is going into the receptacle
unobstructed and engaging the locking element completely
Door status contact output not working
•
Check orientation of rosette (see pg. 3).
Electric Deadbolt
Cabinet Lock
Mini Surface
-
Mount
Deadbolt
Access Control Keypad
with Proximity Reader
SD-997C
-
GCQ
SD-
997B
-
1SQ
SK-1131
-
SPQ
Also Available from
SECO
-
LARM
®
:
Sample Applications:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email:
sales@seco
-
larm.com
®
PITGW1
MI_CL-210M-U3BQ_171024.docx
NOTICE
:
The SECO
-
LARM policy is one of continual development and improvement. For that reason, SECO
-
LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All t
rademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2017 SECO-LARM U.S.A.,
Inc. All
rights reserved.
WARRANTY:
This SECO
-LARM product is warranted against defects in material and workmanship while
used in normal
service for two (2) years from the date of sale to the original customer. SECO-
LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM
’s
option. In no event shall SECO-
LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
IMPORTANT
:
Users and installers of this product are responsible for ensuring this product complies
with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
will not be
held responsible for the use of this product in violation of any current laws or statutes.
Troubleshooting:
Fig. 1
Fig. 2
Fig. 3
Loading...