INSTRUCTIONS FOR
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
INDUSTRIAL VACUUM CLEANER WITH AUTO
START/STOP
MODEL NO: PC200SDAUTO.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
Refer to
instruction
manual
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the correct
fuse - see fuse rating in these instructions.
8 DO NOT pull or carry the appliance by the power cable.
8 DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a rm grip on the plug.
8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualied electrician.
1.1.4. This product is tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualied electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8 DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualied electrician.
1.2. GENERAL SAFETY
9 Disconnect the cleaner from the power supply before servicing, changing accessories, or performing any
maintenance.
9 Use only genuine parts and accessories. Unauthorised parts and accessories may be dangerous and will invalidate your warranty.
9 Maintain the cleaner in good condition. Use an authorised agent for servicing. Keep machine clean, but DO NOT use solvents.
8 DO NOT operate the unit without the locking cartridge filter in place (except when wet vacuuming when the foam sleeve filter is used).
Using the cleaner without a locking cartridge filter will cause machine faults and will invalidate your warranty.
9 Wear protective clothing and gloves.
8 DO NOT allow children or untrained persons to operate the cleaner.
8 DO NOT place attachments close to your face (especially eyes, ears, etc). DO NOT point the hose end at other persons or animals.
▲ DANGER! DO NOT vacuum hot or glowing ash, cigarette ends, inflammable, explosive, corrosive or other dangerous substances.
8 DO NOT leave machine running unattended. Turn power supply OFF and DO NOT leave the vicinity until motor has come to a
complete stop.
8 DO NOT operate the cleaner while under the influence of drugs, alcohol or impairing medication, or if you are tired.
8 DO NOT use the cleaner in the rain or in very damp conditions.
8 DO NOT use the cleaner for a task it is not designed to perform.
Recommended fuse rating
13 Amp
2. INTRODUCTION
Powerful 1400Watt motor head gives incredible suction through Ø35mm hosing. May also be used as a blower. Integral three-pin BS socket
provides power supply for dust-free tools up to 1400W. When used in conjunction with a power tool the cleaner auto-starts when the tool is started
and auto-stops 10 seconds after the tool is switched off to ensure tool and hose are left free of dust. Includes stainless steel drum on two castors
and two fixed wheels & stainless steel telescopic rigid extension tube as well as tools for wet and dry operations. Tool stowage points on head and
base. Supplied with cartridge filter and wet-use foam filter.
© Jack Sealey Limited
Original Language Version
PC200SDAUTO.V3 Issue: 4 (3) 14/03/18
3. SPECIFICATION
Model no: ................................................... PC200SDAUTO.V3
Motor power: .................................................................1400W
Supply: .............................................................................230V
Maximum vacuum pressure: ......................................165mbar
Airflow: .......................................................................120mtr³/h
Drum size: ..........................................................................20ltr
Drum type: ..........................................................stainless steel
Weight: ................................................................................8kg
Vacuum accessories diameter:.....................................Ø35mm
Filter type: ....................................................................cartridge
Replacement filter cartridge: ...................................PC200CFL
Replacement foam filters (pack of 10): ........................PCFF10
Optional dust bag (pack of 10): ...............................PC200PB5
4. CONTENTSt
4.1. Carefully unpack the carton.
4.2. Locate the two side latches (g.1.19) which hold the power
head in place.
4.3. Undo the latches, remove the top section and take out the
items in the container.
4.4. Check and identify each component as listed below. If anything
is missing or damaged please contact your supplier immediately.
Item Description
1 Flexible vacuum hose
2 Noise diffuser
3 Telescopic suction tube
4 Instruction manual
5 Wheel (x2)
6 Combination nozzle
7 Vacuum hose connection
8 Crevice nozzle
9 Dust free tool adaptor
Part No.PC200SDAV3.42
10 Foam filter
11 Locking Cartridge Filter
(fitted as standard)
12 Castors & foot (x2)
13 Four screws in bag
14 Drain cap
15 Container, (Stainless Steel)
16 Dust free tool socket
17 ON/OFF switch, 3 position
18 Handle
19 Clasp, one either side (x2)
fig 1
5. ASSEMBLYy
5.1. Ensure the mains plug is disconnected.
5.2. Undo latches that secure the power head to the stainless
container.
5.3. Lift off the power head and put carefully to one side.
5.4. Locate the castor feet and wheels ready for fitting.
5.5. Turn the container upside down. The castor feet attach to the
lower moulding using a dovetail arrangement. Slot each
foot in turn into the receiving slots either side of the drain
cap and push fully home. Retain each castor foot with the
self tapping screws provided.
5.6. The rear wheels attach to the lower moulding in the same way
but they are handed. Match the moulded in number on each
wheel assembly to the numbers on the lower moulding
and push fully home. Retain each wheel assembly with the
self tapping screws provided.
5.7. For dry vacuum cleaning use the locking cartridge filter supplied.
NOTE: DO NOT operate the cleaner without a cartridge
filter fitted as this will damage the machine and invalidate
your warranty. Ensure the filter is correctly fitted before
every use.
5.8. If wet vacuuming remove the cartridge filter and push the
foam filter over the filter basket instead.
5.9. Replace the top section onto the container.
5.10. Align up the top section with the latches and snap into place,
by applying pressure at the mid point of the clasps.
© Jack Sealey Limited
Original Language Version
PC200SDAUTO.V3 Issue: 4 (3) 14/03/18
Loading...