Sealer Sales W-300T, W-450T, W-600T User Manual

Double Impulse Foot Sealers
Model: W-300T, W-450T, W-600T

Distributed By:

Version 1.1_2014

General Information

Thank you for purchasing our W-Series Double Impulse Foot Sealers.

This owner’s manual contains information relating to your sealer. The manual will provide you
with basic information concerning both operation and maintenance of your new machine. Please
read it carefully as failure to do so may result in bodily injury and/or damage to the equipment.

Please fill in the information below. You will find the information on the machine identification
plate. You will need this information when ordering replacement parts or making technical
inquiries.

No part of this manual may be duplicated, reproduced, stored in a retrieval system, translated,
transcribed, or transmitted in any form without the express prior written permission of Sealer Sales.

W H D F E Q U I P M E N T I N F O R M A T I O N

 Model #

 Serial #

 Purchase Date:

 Reference # (found on packing slip)

 Owner:

W H D F I N S T R U C T I O N M A N

Safety Instructions

WARNING!

understood priortosettinguporoperating yourequipment.R ead and fullyunderstand all instructionsand

warningspriortousing thisunit.Yoursafetyismostimportant!Failure tocompl

resultinseriousinjuryorpropertydamage.R emember:

responsibility.

Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to

and take necessary precautions can result in serious injury as well as damage to

Never operate or service your sealer until you have read this manual completely and understand it

Plug the sealer into a standard 120 Volt, 60Hz wall outlet

Do not use the sealer if the power cord, plug or any other parts are damaged. Be sure not to allow

the power cord to drape into your work area. Check that all parts are operating properly and

perform the intended functions.

other conditions that may affect the operation.

Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before

to the power source.

sealer from power source before servicing, changing accessories or cleaning the

To provide protection against the risk of electrical shock, the power connection must be properly

Do not leave the sealer unattended when in use.

before leaving the work area.

is used solely for sealing thermoplastic materials. Using the machine for any other purpose

can cause damage to the machine and operator.

While operating machinery, wear cl

external items from getting caught in the machine. Do not wear jewelry when operating the sealer.

B eloware generalsafetyprecautionsand warningsthatshould be

ywithproceduresmay

Your personal safety is your

or surge protector.

r any worn parts before starting operation.

Disconnect the sealer from the power source

fitting clothing and tie back long hair to prevent any

follow these safety rules
equipment.



fully.

U A L







connecting

 Always disconnect

unit.



grounded at all times.



 Sealer



Check fo

ose-

Check for all

2

W H D F I N S T R U C T I O N M A N U A L



Never touch the heating element(s) with bare hand while the sealer is plugged into a power source,
in operation or just finished operation. Touching heated areas may cause fire and/or severe burns.

 While machine is in operation, do not place fingers, tools, or other foreign objects on or into the

machine. Do not place hands or fingers near pinch points. Do not touch machine while it is in
operation. Perform all procedures carefully and watch where hands and fingers are at all times.

 The sealer is not water resistant or water proof. Spraying down the machine will damage machine

or cause electrical shock. Do not submerge the sealer into water or liquid.

 Do not operate sealer in a corrosive or humid environment.

 Always keep the machine clean, lubricated and in good working condition. Follow any

maintenance and lubrication procedures outlined in this manual. Make sure unit is disconnected
from power source before cleaning.

 NEVER use any accessories or parts from other manufacturers. Machine should not be altered or

modified using parts that are not genuine authorized parts. Doing so will VOID YOUR
WARRANTY.



When replacing the heating elements, always replace the PTFE adhesive under the
heating element. A worn PTFE adhesive can cause the heating element to break.

The
PTFE adhesive works as a barrier between the body of the sealer and the element. Never allow
the element to come in direct contact with the sealer body as that will damage the timer.

 Never leave the sealer unattended. Be safe, disconnect the sealer from power source before

leaving work area.

 Always keep out of reach of children and pets.

 Close supervision is necessary when any appliance is near persons with reduced physical, sensory

or mental capabilities or lack of experience and knowledge . This sealer is NOT to be used by
children or by persons with reduced physical, sensory or mental capabilities or lack of experience
and knowledge.

 DO NOT use the sealer outdoors.

 DO NOT use the sealer while under the influence of drugs, medications or alcohol.

SAVE THESE INSTRUCTIONS - REFER TO THEM OFTEN AND USE THEM TO INSTRUCT

OTHERS.

3

W H D F I N S T R U C T I O N M A N U A L

4

W-300T

W-450T

W-600T

Power

110V/60Hz

110V/60Hz

110V/60Hz

Watts

1000W

1900W

2800W

Sealing Length

/ Width

11.8"

/ 5mm

17.6"

/ 5mm

23.4"

/ 5mm

Standing Height

33 1/2"

33 1/2"

33 1/2"

Working Table Dimensions

12" x 6"

12" x 6"

12" x 6"

Tray Adjustment Height

Up to 6.5"

Up to 6.5"

Up to 6.5"

Throat Depth

1 1/2"

1 1/2"

1 1/2"

Dimensions

13" x 14" x 34"

21" x 14" x 34"

26 1/4" x 14" x

34"

Shipping Dimensions

21" x 20" x 12"

26" x 20" x 12"

33" x 20" x 12"

Gross Weight

34lbs / 29lbs

45lbs / 29lbs

49lbs / 29lbs

Basic

Introduction

W-Series double impulse foot sealers are ideal for high volume poly bag and other thermoplastic sealing.
Equipped with top and bottom heating elements, our double impulse sealers can seal thicker
thermoplastic materials up to 20mil in total thickness. Single/double sealing switch selector provides the
sealer with the flexibility to seal different types of materials. The sealer allows you to keep both hands
free for quicker and more accurate sealing.

Features of the W-Series Double Impulse Foot Sealers

Y ourfootsealerisequipped witha wide range ofstandard featuresand capab ilities.

 Impulse sealing - no warm up time needed
 Plug-in electronic timer for variable control
 Single or double sealing switch selector
 Heavy duty all metal construction
 Sits on rectangular stand for stability
 Adjustable work table height
 Optional: Taller stand and tension rod available adding 10" height
 Manufacturer spare parts kit includes: 2 heating elements

How Do W-Series Double Impulse Foot Sealers Work?

Our W-Series double impulse foot sealers fire a short burst of electricity through a

Principles

Place material on lower
jaw and activate
footboard

specially designed heating wire to weld thermoplastic materials together. The
length of the seal time will depend on the sealing characteristics of the bag being

sealed. The sealing process is simple: The operator places the bag between the
sealing jaws and presses the footboard to activate the unit. The operator retrieves the sealed bag and
repeats the process. Our W-Series double impulse sealers utilize twin heating element wires, one on the
upper sealing jaw and one on the bottom sealing jaw providing greater heat penetration for sealing
through thicker materials (up to 20mil total thickness).

Specifications

38" x 19" x 10"

38" x 19" x 10"

38" x 19" x 10"