Sealer Sales W-600A, W-605A, W-455A, W-450A, W-305AT User Manual

Automatic Sealers
Models: W-300A, W-305A, W-450A, W-455A, W-600A, W-605A
W-3010A, W-4510A, W-6010A, W-755AA, W-905AA, WN­1205AA, WN-1505AAA, W-305AT, W-455AT

Distributed By:

Version 1.4.2
Last Updated 3/25/19

W H A I N S T R U C T I O N M A N U AL

Copyright © 2015 by Stephanie Hwang

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying,
recording, or other electronic or mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations embodied in
critical reviews and certain other noncommercial uses permitted by copyright law. For permission requests, write to the publisher, addressed “Attention:
Permissions Coordinator,” at the address below.

Sealer Sales, Inc.
8820 Baird Avenue
Northridge, Ca 91324
www.sealersales.com

Printed in the United States of America

1

W H A I N S T R U C T I O N M A N U AL

W H A E Q U I P M E N T I N F O R M A T I O N

 Model #

 Serial #

 Purchase Date:

 Reference # (found on packing slip)

 Owner:

General Information

Thank you for purchasing our W-Series Automatic Sealers

This owner’s manual contains information relating to your sealer. The manual will provide you with
basic information concerning both operation and maintenance of your new machine. Please read it
carefully as failure to do so may result in bodily injury and/or damage to the equipment.

Please fill in the information below. You will find the information on the machine identification plate.
You will need this information when ordering replacement parts or making technical inquiries.

No part of this manual may be duplicated, reproduced, stored in a retrieval system, translated, transcribed, or
transmitted in any form without the express prior written permission of Sealer Sales.

2

W H A I N S T R U C T I O N M A N U AL

Safety Instructions

WARNING!

Below are general safety precautions and warnings that should be

understood prior to setting up or operating your equipment. Read and fully understand all instructions and
warnings prior to using this unit. Your safety is most important! Failure to comply with procedures may
result in serious injury or property damage. Remember:

responsibility.

Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to follow these
safety rules and take necessary precautions can result in serious injury as well as damage to equipment.

 Never operate or service your sealer until you have read this manual completely and understand it fully.
 Plug the sealer into a standard 120 Volt, 60Hz wall outlet or surge protector.
 Do not use the sealer if the power cord, plug or any other parts are damaged. Be sure not to allow the

power cord to drape into your work area. Check that all parts are operating properly and perform the
intended functions. Check for any worn parts before starting operation. Check for all other conditions that
may affect the operation.

 Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before attaching

to the power source.

 Always disconnect sealer from power source before servicing, changing accessories or cleaning the unit.
 To provide protection against the risk of electrical shock, the power connection must be properly grounded

at all times.

Your personal safety is your

 Do not leave the sealer unattended when in use. Disconnect the sealer from the power source before

leaving the work area.

 Sealer is used solely for sealing thermoplastic materials. Using the machine for any other purpose can cause

damage to the machine and operator.

 While operating machinery, wear close-fitting clothing and tie back long hair to prevent any external items

from getting caught in the machine. Do not wear jewelry when operating the sealer.



Never touch the heating elements with bare hand while the sealer is plugged into a power source, in
operation or just finished operation. Touching heated areas may cause fire and/or severe burns.

3

W H A I N S T R U C T I O N M A N U A L

4

 While machine is in operation, do not place fingers, tools, or other foreign objects on or into the machine.

Do not place hands or fingers near pinch points. Do not touch machine while it is operation. Perform all
procedures carefully and watch where hands and fingers are at all times.

 The sealer is not water resistant or water proof. Spraying down the machine will damage machine or cause

electrical shock. Do not submerge the sealer into water or liquid.

 Do not operate sealer in a corrosive or humid environment.

 Always keep the machine clean, lubricated and in good working condition. Follow any maintenance and

lubrication procedures outlined in this manual. Make sure unit is disconnected from power source before
cleaning.

 NEVER use any accessories or parts from other manufacturers. Machine should not be altered or modified

using parts that are not genuine authorized parts. Doing so will VOID YOUR WARRANTY.

 Never leave the sealer unattended. Be safe, disconnect the sealer from power source before leaving work

area.

 Always keep out of reach of children and pets.
 Close supervision is necessary when any machine is near persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge . This sealer is NOT to be used by children or by persons
with reduced physical, sensory or mental capabilities or lack of experience and knowledge.

 Do NOT use the sealer outdoors.
 Do NOT use the sealer while under the influence of drugs, medications or alcohol.

SAVE THESE INSTRUCTIONS - REFER TO THEM OFTEN AND USE THEM TO INSTRUCT OTHERS.

5

Basic
Principles

Place material on lower
jaw and activate
footswitch

Introduction

W-Series automatic sealers are ideal for high volume continuous poly bag and other thermoplastic sealing.
The sealer allows you to keep both hands free for quicker and more accurate sealing. Our W-Series auto
sealers can seal polyethylene, polypropylene, saran, nylon, static shielding bags, Mylar up to 30mil in total
thickness depending on the model # of the sealer.

Features of the W-Series Automatic Sealers

Your automatic sealer is equipped with a wide range of standard features and capabilities.

 Simple to use - no operator training needed
 Impulse sealing - no warm up time needed
 Dual mode operation: auto or manual
 Foot switch allows hands free operation
 Die cast construction
 3 separate control settings for sealing time, recycle time, and congealing time
 Includes electric foot switch and adjustable work table
 Equipped with either 2.7mm, 5mm, or 10mm seal widths
 Option: double impulse sealing with heat on both sealing bars for sealing thicker materials
 Manufacturer spare parts kit includes: 2 heating elements

How Do W-Series Automatic Sealers Work?

Our W-Series automatic impulse sealers fire a short burst of electricity through a
specially designed heating wire to weld thermoplastic materials together. The
length of the seal time will depend on the sealing characteristics of the bag being

sealed. The sealing process is simple: The operator places the bag between the
sealing jaws and presses the footswitch to activate the unit. The sealer is equipped with a digital display
for easy timer settings. The seal process ends automatically once the preset seal time is reached. The
operator retrieves the sealed bag and repeats the process. Bags are sealed repeatedly and uniformly.

6

W-300A
W-305A

W-3010A

W-450A
W-455A

W-4510A

W-600A
W-605A

W-6010A

W-755AA

Power

110V/60Hz

Watts

450W
600W

1000W

600W
800W

TBD

800W

1300W

TBD

1200W

Seal Width

2.7mm
5mm

10mm

2.7mm
5mm

10mm

2.7mm
5mm

10mm

5mm

Sealing Length

12"

18"

24"

30"

Net Weight

40lbs
42lbs
43lbs

45lbs
45lbs
46lbs

49lbs
53lbs
54lbs

79lbs

Dimensions

17" x 14" x 8"

21" x 14" x 8"

27" x 14" x 8"

33" x 14" x 10"

Gross Weight

47lbs
48lbs
49lbs

51lbs
51lbs
53lbs

55lbs
61lbs
62lbs

82lbs

Shipping Dimensions

25" x 19" x 13"

25" x 19" x 13"

31" x 20" x 13"

38" x 21" x 4"

WN-905AA

WN-1205AA

WN-1505AAA

Power

110V/60Hz

110V/60Hz

110V/60Hz

Watts

1400W

1500A

2000W

Seal Width

5mm

5mm

5mm

Sealing Length

35"

47"

59"

Net Weight

88lbs

104lbs

123lbs

Dimensions

39" x 15" x 10"

51" x 15" x 10"

63" x 15" x 10"

Gross Weight

90lbs

106lbs

126lbs

Shipping Dimensions

45" x 21" x 14"

56" x 21" x 14"

67" x 21" x 14"

Specifications - Single Impulse Sealing

Single impulse automatic sealers are equipped with one heating element (lower sealing jaw).

Specifications - Special Order Automatic Sealers

Our special order automatic sealers are equipped with double or triple electromagnets.