Sealer Sales W-300DT, W-300DTS User Manual

Direct Heat Foot Sealers

Models: W-220DT(S), W-300DT(S), W-450DT(S)

Distributed By:

Version 1.1

Copyright © 2014 by Stephanie Hwang

All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying,
recording, or other electronic or mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations
embodied in critical reviews and certain other noncommercial uses permitted by copyright law. For permission requests, write to the publisher,
addressed “Attention: Permissions Coordinator,” at the address below.

Sealer Sales, Inc.
8820 Baird Avenue
Northridge, Ca 91324
www.sealersales.com

Printed in the United States of America

W H D T I N S T R U C T I O N M A N U A L

General Information

Thank you for purchasing our W-Series Direct Heat Foot Sealers.

This owner’s manual contains information relating to your sealer. The manual will provide you
with basic information concerning both operation and maintenance of your new machine. Please
read it carefully as failure to do so may result in bodily injury and/or damage to the equipment.

Please fill in the information below. You will find the information on the machine identification
plate. You will need this information when ordering replacement parts or making technical
inquiries.

No part of this manual may be duplicated, reproduced, stored in a retrieval system, translated,
transcribed, or transmitted in any form without the express prior written permission of Sealer Sales.

W H D T E Q U I P M E N T I N F O R M A T I O N

 Model #

 Serial #

 Purchase Date:

 Reference # (found on packing slip)

 Owner:

2

W H D T I N S T R U C T I O N M A N

U A L

Safety Instructions

WARNING!

understood prior to setting up or operating your equipment. Read and fully understand all instructions and

warnings prior to using this unit. Your safety is most important! Failure to compl

result in serious injury or property damage. Remember:

Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to

and take necessary precautions can result in serious injury as well as damage to

Never operate or service your sealer until you have read this manual completely and understand it

Plug the sealer into a standard 120 Volt, 60Hz wall outlet

Do not use the sealer if the power cord, plug or any other parts are damaged. Be sure not to allow

the power cord to drape into your work area. Check that all parts are operating properly and

perform the intended functions.

other conditions that may affect the operation.

Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before

to the power source.

sealer from power source before servicing, changing accessories or cleaning the

To provide protection against the risk of electrical shock, the power connection must be properly

Do not leave the sealer unattended when in use.

is used solely for sealing thermoplastic materials. Using the machine for any other purpose

can cause damage to the machine and operator.

While operating machinery, wear cl

external items from getting caught in the machine. Do not wear jewelry when operating the sealer.

Below are general safety precautions and warnings that should be

y with procedures may

Your personal safety is your

r any worn parts before starting operation.

Disconnect the sealer from the power source

fitting clothing and tie back long hair to prevent any

responsibility.

follow these safety rules
equipment.



fully.







connecting

 Always disconnect

unit.



grounded at all times.



before leaving the work area.

 Sealer



Check fo

ose-

or surge protector.

Check for all

3

W H D T I N S T R U C T I O N M A N U A L



Never touch the sealing bars with your bare hands while the sealer is plugged into a power source,
in operation or just finished operation. Touching heated areas may cause fire and/or severe burns.

 While machine is in operation, do not place fingers, tools, or other foreign objects on or into the

machine. Do not place hands or fingers near pinch points. Do not touch machine while it is in
operation. Perform all procedures carefully and watch where hands and fingers are at all times.

 The sealer is not water resistant or water proof. Spraying down the machine will damage machine

or cause electrical shock. Do not submerge the sealer into water or liquid.

 Do not operate sealer in a corrosive or humid environment.

 Always keep the machine clean, lubricated and in good working condition. Follow any

maintenance and lubrication procedures outlined in this manual. Make sure unit is disconnected
from power source before cleaning.

 NEVER use any accessories or parts from other manufacturers. Machine should not be altered or

modified using parts that are not genuine authorized parts. Doing so will VOID YOUR
WARRANTY.

 Never leave the sealer unattended. Be safe, disconnect the sealer from power source before

leaving work area.

 Always keep out of reach of children and pets.

 Close supervision is necessary when any appliance is near persons with reduced physical, sensory

or mental capabilities or lack of experience and knowledge . This sealer is NOT to be used by
children or by persons with reduced physical, sensory or mental capabilities or lack of experience
and knowledge.

 DO NOT use the sealer outdoors.

 DO NOT use the sealer while under the influence of drugs, medications or alcohol.

SAVE THESE INSTRUCTIONS - REFER TO THEM OFTEN AND USE THEM

TO INSTRUCT OTHERS.

4

5

Introduction

W-Series Direct Heat Foot Sealers are designed for sealing many different types of thermoplastic
materials including: coated aluminum foil, Kraft paper, cellophane, polypropylene, poly-nylon, and other
thicker materials up to 20mil in total thickness. Please note that our direct heat sealers would not be
appropriate for sealing polyethylene and/or polyvinyl chloride.

Features of the W-Series Direct Heat Foot Sealers

Your Direct Heat foot sealer is equipped with a wide range of standard features and capabilities.

 Direct heat sealing / constant heat sealing system
 Heavy duty all metal construction
 26" pedestal stand with optional 36" stand available
 Simple to use - minimal operator training
 German manufactured temperature controller that maintains the seal bars at a proper temperature

providing consistent seal quality

 Electronic timer (0-6 seconds) to adjust sealing time providing for consistent seal quality
 Equipped with protector bars around the sealing bars to prevent injury
 Hands free sealing activated by footswitch
 Sealing width: 1/2" (15mm)
 Adjustable work table
 Options: meshed (T-version) or serrated (TS-version) sealing bars

Figure1. Meshed seal line

Figure 2. Serrated seal line