SeaLand Traveler 500 Plus Series, Traveler Lite 100 Series, SEALAND 2000 Series, Traveler 2000 Series Owner's Manual

®

SEALAND

FINE CHINA TOILET

OWNER’S MANUAL

Traveler® 500

Traveler Lite

Plus

Series, 2000 Series,

®

100 Series Toilets

WARNING

!

This manual must be read and under­stood before installation, adjustment,
service, or maintenance is performed.
Modification of this product can
result in property damage.

Dometic Corporation

13128 State Rt. 226, P.O. Box 38

Big Prairie, OH 44611-0038 USA

SeaLand Product Hotline [phone]

(8:00 a.m. - 5:00 p.m. ET)

1

2

TABLE OF CONTENTS

Important Information .............................................. 3

Toilet Model Identification ....................................... 3

How to Use ............................................................ 3

Installation.............................................................. 4

Pedestal and Pedal Cover Installation..................... 4

Proper Cleaning and Maintenance .......................... 5

Winterizing ............................................................. 5

Deodorants and Special Tissue .............................. 6

Service Tip ............................................................. 6

Troubleshooting Guide ....................................... 7 - 9

100 Series Parts List ........................................... 10

500 Plus Series Parts List .................................... 11

2000 Series Parts List .......................................... 12

Dimensional Specifications................................... 13

Ordering Parts ...................................................... 14

Parts Distributors ................................................. 14

Manufacturer’s Limited Warranties ....................... 16

IMPORTANT INFORMATION

1. Do not use chlorine or caustic chemicals, such as laundry bleach or drain opening types, in the system. These
products damage the seals in toilets and dump valves.

2. Do not permit foreign objects (paper towels, paper cups, diapers, sanitary napkins, etc.) to be flushed through
the toilet.

3. Mechanical seal toilets, like SeaLand Traveler units, are designed to only discharge directly into a holding
tank. Horizontal pipe runs as found in conventional residential or commercial plumbing systems cannot be
accommodated.

4. Toilet bowl and flush seals must be regularly cleaned and winterized according to “Proper Cleaning and
Maintenance” and “Winterizing” procedures on page 5, or your warranty coverage may be voided.

TOILET MODEL IDENTIFICATION

The model identification label is located on the toilet base
and will show the model number and serial number. Follow
instructions for removing toilet pedestal cover in “Pedestal
and Pedal Cover Installation” on page 4. Traveler Lite Model
110 identification label is on the back of the base. If label is
not available, please refer to “Dimensional Specifications”
on page 13 for toilet model identification.

DOMETIC CORPORATION

P.O. BOX 38, 13128 STATE RT 226 [phone]
BIG PRAIRIE, OH 44611 USA

MODEL NO.

SERIAL NUMBER

000

000000

HOW TO USE

To prepare the Traveler toilet for use, check to be sure water supply to the toilet is connected. Turn on water supply and
check system for leaks. Flush toilet and check for leaks.

To properly use the Traveler toilet, follow these simple instructions:

1. To add water to the toilet, lift or raise the flush lever until desired water level is reached.

Generally, more water is required only when flushing solids.

2. To flush toilet, push lever all the way down until contents leave toilet bowl. Water flow pressures vary at

different locations, therefore holding the flush lever down for 4-8 seconds may be required. We require a
minimum flow to the toilet of two gpm (7.6 lpm) for proper rim and bowl wash.

3. Release flush lever by allowing it to snap back, which permits positive sealing around the flush ball.

4. A small amount of water should remain in bowl.

Note: Holding flush lever down longer than necessary results in excessive water usage.

3

INSTALLATION

1. To replace an older toilet, turn off water supply to toilet.

Disconnect water line at toilet water valve. Unscrew floor bolt
nuts and remove toilet. Discard old floor seal and mounting
bolts. The old floor flange may be used if it is in good
condition and has four (4) bolt locations. [Only two bolts are

All Traveler toilets

and Traveler Lite

Model 111

(4-bolt connection)

Traveler Lite

Model 110

(2-bolt connection)

required for Traveler Lite Model 110.]

NOTE: If old floor flange cannot be used and cannot be
removed, please use a SeaLand Universal Mounting Kit,
available from your SeaLand dealer.

Fig. A

2. When installing new floor flange, make certain that the toilet

mounting bolts align properly with Traveler toilet mounting
pattern.

3. Secure flange to floor using flat head screws through

countersunk holes in flange. Insert floor bolts into slotted holes

Fig. B

in flange (Figure A).

4. If toilet is being installed in a shower stall, apply a 1/4" thick

by 3/4" wide bead of glazing compound around the circumfer­ence of the floor flange (Figure B).

5. Install seat assembly with hinges and screws provided.

Traveler Models 510/511 will also accept handicap or house­hold decorative seats. [Traveler Lite Models 110/111 seats
are already installed.]

6. Position floor seal by pressing the floor bolts up through holes

in the seal.

7. Set toilet in place with bolts protruding up through mounting

holes in base (Figure C).

8. Install washers and hex nuts provided with toilet. Snug nuts

Fig. C

Fig. D

Insert
two
wood
screws
in rear
of base.

down equally with standard 7/16" open end wrench. Remove
excess glazing compound from around base in shower stall
installation. For Traveler Lite Model 110, also install two wood
screws provided in two holes at rear of base. (See Figure C).

9. Connect water supply line to water valve (1/2" MPT) inlet

using appropriate fittings or an extension (Figure D). For
Traveler Lite Model 110, you must remove water valve cover
from flush pedal before connecting water supply line (see instructions below).

10. Turn on water supply and flush toilet to test for leaks.

11. For all models except Traveler Lite Model 110, attach pedestal and pedal covers to toilet base (see installation

instructions below).

PEDESTAL AND PEDAL COVER INSTALLATION

ALL TRAVELER TOILETS AND TRAVELER LITE MODEL 111:

1. Wrap pedestal cover
around base so that it
closes as shown.

TRAVELER LITE MODEL 110:

1. Press button on back of
pedal to release water
valve cover.

2. Tall model – screw
cover together. Short
model – snap together.

3. Slide pedal cover onto
foot pedal rod.

2. Pull on bottom of cover
to remove it. Cover
snaps back into place.

4

4. Secure side plate onto
pedal cover with screws.

PROPER CLEANING AND MAINTENANCE

The Traveler toilet should be cleaned regularly for maximum sanitation and opera­tional efficiency. You can clean it just as you would a household toilet. Do not use

caustic chemicals, such as drain-opening types, as they will damage
the seals.

BOWL CLEANING: For stubborn stains, use SeaLand® Bowl and Seal Cleaner

(Fig. A). It’s manufactured especially for use with Traveler and Traveler Lite toilets.
In certain locations where water is hard, a build-up of lime may dull the toilet bowl
finish. Restore the shine with this SeaLand cleaner. If you cannot find it in your
area, contact SeaLand for your nearest dealer. If the cleaner is not available, you
can also use Bar Keepers Friend® cleanser. It is not necessary to vigorously scrub
with either product. Please follow label instructions.

SEAL CLEANING: After an extended time, mineral deposits from hard water can
build up under the edge of the rubber bowl seal, resulting in a slow leakdown of
water from the bowl. To prevent this mineral build-up, periodically clean under the
bowl seal with SeaLand Bowl and Seal Cleaner (Fig. B).

1. Shut off water supply.

2. Apply cleaner onto the seal cleaning tool (supplied with new toilet), open the
flush ball by pressing on flush lever, and scrub under the seal. Make sure to
push bristles between bottom of seal and top of flush ball surface to scrub all
parts of seal that come into contact with flush ball.

3. Close ball and wait 2-3 minutes.

4. Open flush ball. Use brush and water to rinse away cleanser and loosened deposits.

Fig. A

Fig. B

WINTERIZING

At the end of each season, the Traveler or Traveler Lite toilet should be winterized
for storage, by either draining or using potable water-safe antifreeze in the system.

To drain:

1. Thoroughly flush system with fresh water.

2. Empty holding tank.

3. Shut off water supply to toilet(s), and remove inlet waterline (Fig. C).

Do not remove brass cap on bottom of valve.

4. Press flush lever until all water is drained from toilet(s).

To use antifreeze:

1. Drain potable water tank.

2. Add freshwater antifreeze to potable water tank.

3. Flush potable water antifreeze and water mixture through toilet(s) and into the waste holding tank. Each
installation is different, so amounts may vary. User discretion is required to assure adequate protection.

4. Empty holding tank.

NOTE: Use nontoxic antifreeze designated for potable water systems. (See vehicle owner’s manual.)
CAUTION: Never use automotive-type antifreeze in freshwater systems.

Fig. C

5

DEODORANTS AND SPECIAL TISSUE

Your Traveler toilet requires the regular addition of a deodorant product to reduce malodors and to help break down
holding tank contents. Several factors should be considered in selecting a deodorant product.

Liquid or Granulated: Liquid products obviously work more quickly by readily going into solution. Granulated powder
formulations, on the other hand, have the advantage of requiring less storage space and are less likely to leak if the
package is inadvertently damaged.

Formaldehyde versus Non-Formaldehyde: Dometic manufactures both types of deodorants. Generally speaking,
formaldehyde formulas control odor very effectively at all temperatures and with all degrees of water hardness. SeaLand
Environment-Friendly brand, which is formaldehyde free, is similarly effective.

How Much Deodorant and How to Add It: The deodorant is added directly into the toilet bowl, then flushed into the
holding tank. Follow bottle or package instructions. Conditions of extremely warm weather, longer waste holding time
and larger tank capacities may require more deodorant treatment. Also, to maintain optimum efficiency in odor control,
the waste holding tank should be cleaned thoroughly at least once or more each season depending on use.

Why Not Use Household Toilet Paper in Your Traveler Toilet. Household tissues often contain adhesives which
bond together the paper fibers from which the tissue is made. The adhesives prevent the tissue from breaking apart,
and their use in “ultra-low flow” systems can cause system clogging. SeaLand tissue is especially designed for use in
low water toilet systems. Its rapid dissolving properties minimize the amount of residual paper in the holding tank and
allow deodorizers to work more efficiently.

SeaLand Brand versus Other Brands: We constantly strive to provide our system owners with effective products
that have minimal environmental impact and good value. Many deodorant products do not measure up to our standards
of performance and value.

SeaLand® Liquid

SeaLand® Granulated

Deodorant

Six 2-oz. pouches

®

SeaLand

Two 8-oz. bottles

Liquid

Deodorant

Part No.

379224008

Deodorant -

Environment Friendly

32-oz. bottle

Part No.

379114032



Part No.

379626002

SERVICE TIP

Checking for water leaks behind or under toilets or other appliances can make it difficult to locate the source. Dripping
water at room temperature makes it difficult to feel wetness. Taking four or five sheets of toilet tissue and wiping all
seams and waterline connections offers a simple means of locating the general area of the leakage. Start at the top of
the unit since gravity will cause a leak to run downward. When the tissue comes in contact with the leaking water, it will
immediately change texture.

SeaLand

Cleaner

16-oz. bottle

Part No.

379314016

6

SeaLand

®

Rapid-Dissolving

Toilet Tissue

Four 400-sheet rolls

Part No. 379441204

®

TROUBLESHOOTING GUIDE

TRAVELER TOILET

BASE ASSEMBLY

(except model 110)

WATER VALVE ASSEMBLY

TOP VALVE CAP

FILTER SCREEN

PEDAL

COVER

TRAVELER LITE MODEL 110

BASE ASSEMBLY

WATER VALVE ASSEMBLY

TOP VALVE CAP

ADJUSTING NUT

CAM STRAP

VALVE BODY

WATER VALVE SCREWS

FLUSH PEDAL

SPRING
CARTRIDGE

ADJUSTING NUT

FLUSH BALL

BALL SEAL

BOWL SEAL

BAND CLAMP

FLUSH BALL

SHAFT

BALL SEAL

BOWL SEAL

BAND CLAMP

FILTER SCREEN

VALVE BODY

PEDAL

COVER

WATER
VALVE
SCREWS

TRAVELER TOILET BOWL, REAR VIEW

(Models 510+, 511+, 2010, 2011)

WHITE CAP

VACUUM

BREAKER

VACUUM BREAKER/BOWL CONNECTION

CONNECTION

SPRING
CARTRIDGE

HOSE

SHAFT

TRAVELER LITE TOILET BOWL, REAR VIEW

(Models 110, 111)

VACUUM

BREAKER

VACUUM BREAKER/BOWL CONNECTION

HOSE

CONNECTION

7

TROUBLESHOOTING GUIDE (cont'd)

Problem Possible Cause Service Instructions

1. Toilet emits odor (flush ball
open).

a. Odor emitting from base of toilet.
b. Plugged holding tank vent line.

a. Use SeaLand brand deodorants.
b. Clear obstruction from vent line.

2. Water will not stay in bowl.

3. Flush ball will not close
completely.

4. Flush ball will not open.

a. Loose band clamp.

b. Improper seal around flush ball

due to dirt or debris on underside
of ball seal.

c. Worn or damaged seal.
d. Worn or damaged flush ball.

a. Too much friction between flush

ball and ball seal.

b. Water valve screws are too tight.
c. Defective spring cartridge.

a. Broken shaft.
b. Shaft not fully engaged in the

spring cartridge.

a. Tighten adjusting screw.
b. Inspect flush ball and underside

of seal for foreign objects. Clean
under seal if needed (see page 5.
Cleaning tool available – part no.

600344236).
c. Replace seal.
d. Replace flush ball.

a. Lubricate between flush ball and

ball seal with furniture polish or

cooking spray.
b. Loosen screws slightly.
c. Check spring tension by pushing

flush lever down, then release it

suddenly. If lever does not snap

back to original position, replace

spring cartridge.

a. Replace shaft.
b. Put pressure on shaft from under

the flush ball (pushing into spring

cartridge) until it engages. You

may have to rotate flush ball

slightly until shaft lines up with

square in spring cartridge.

5. Flush ball does not open

completely. Applies to

short-base units mounted
on step or riser only.

6. Water does not shut off in
toilet (toilet overflows).

7. Hand spray unit leaks.

8. Water does not enter toilet
bowl properly.

a. Floor flange interferes with flush ball

rotation.

a. Not enough clearance between

cam strap and top of water valve
cap.

b. Dirt lodged in water valve seal.

c. Worn or defective water valve.
d. Worn or defective spring cartridge.

a. Hand sprayer is defective.

a. Insufficient water flow rate at toilet.

b. Water valve clogged.

c. Plugged rim wash holes in toilet.

a. Loosen mounting bolts and push

toilet base back. If this does not
solve problem, install a SeaLand
Universal Mounting Kit (part no.
310139, 310140, or 310141) with
existing floor flange.

a. Adjust cam strap to have .02" -

.06" (.5mm - 1.5mm) clearance
with top of water valve cap. (Does
not apply to model 110.)

b. Dissassemble and clean water

valve.
c. Replace water valve.
d. Replace spring cartridge.

a. Replace hand sprayer.

a. Check water flow rate at toilet.

Rate should be 2 gpm (7.6 lpm) at

toilet.
b. Remove and clean screen located

at inlet of water valve.
c. Clean holes. If still a problem,

replace the toilet bowl.

8

TROUBLESHOOTING GUIDE (cont'd)

Problem Possible Cause Service Instructions

9. Water is leaking from
water valve.

a. Water valve body cracked due to

freeze damage.

b. Water line connection is loose or

not seated properly.
c. Defective water valve.
d. Stripped threads.

a. Replace water valve.

b. Insure that threads are not cross-

threaded and tighten.
c. Replace water valve.
d. Replace water valve.

10. Water is leaking from
bottom of toilet base.

11. Water is leaking from rear
of toilet bowl.

12. Water is leaking from the
base/toilet connection.

a. Toilet is not secured to floor.
b. Worn or defective toilet mounting

floor seal.
c. Cracked base.
d. Worn or defective floor flange.

a. Worn or defective vacuum breaker.

b. Loose vacuum breaker.

c. Cracked or defective toilet bowl.

a. Band clamp may be loose.

b. Ball and bowl seals may be worn

or defective.

a. Tighten toilet mounting bolts.
b. Replace floor seal between floor

flange and toilet base.
c. Replace base assembly.
d. Replace floor flange.

a. Remove white cap from vacuum

breaker. Flush toilet. If water

leaks during flush, vacuum

breaker needs to be replaced.
b. Secure vacuum breaker

connection.
c. Replace toilet bowl. If loose, push

breaker into bowl.

a. Remove plastic base cover (on

applicable models) and tighten

the band clamp.
b. Replace ball and bowl seals.

9

TRAVELER LITE® PARTS LIST

MODEL 111

MODEL 110

Item

1

2

3

4
5

6
7
8

111 110

385344088
385344089

385310790
385310791

385310048
385316140

385310801

385310802

385318162
600341549
385345889

385345892

385343765

307344653

385344088
385344089

385310790
385310791

385310025
385310048

385316140
385310792

385310793

385310681
600343938
385345889

385345892

385343765

307344653

Description

Seat Assembly, White
Seat Assembly, Bone

China Bowl Kit, White
China Bowl Kit, Bone

Band Clamp & Half Clamp Kit, White
Band Clamp & Half Clamp Kit, Bone

®

Teflon

& Rubber Seal Kit

Base Kit, White (includes 3, 4, 6,
7, 9, 10A, 11, 12)
Base Kit, Bone (includes 3, 4, 6,
7, 9, 10A, 11, 12)
Base Kit, White (includes 3, 4, 6,
7, 9, 10, 11, 12, 13, 17)
Base Kit, Bone (includes 3, 4, 6,
7, 9, 10, 11, 12, 13, 17)

Ball, Shaft & Cartridge Kit
Floor Flange Seal
Floor Flange Adapter, 3" MPT

(sold separately)
Floor Flange Adapter, 3" Socket
(sold separately)
Floor Flange Adapter, 3" Spigot
(sold separately)
Floor Flange Adapter, 45º Swivel
(sold separately)

Item

9

10

10A

11
12
13
14

15
15A
15B
15C

16

17

385310064

385310117
385310118

385314349
385236096
600340825
600340177
385310687
385319054
600340683
385230335
385310795

385310796
385310108

385310109

385310794
385310803

385310682
385310762

385314349
385310683

600340177
385310687
385319054
600340683
385230335
385310795

385310796

Description111 110

Floor Bolt Mounting Kit
Floor Bolt Mounting Kit, White
Floor Bolt Mounting Kit, Bone

Pedal Cover Kit, White
Pedal Cover Kit, Bone

Flush Pedal Kit, White (incl. 12)
Flush Pedal Kit, Bone (incl. 12)

Water Valve Kit
Spring Cartridge Kit
Flush Lever
Supply Hose, Bone
Vacuum Breaker Kit
Vacuum Breaker Kit w/ Spray
Hand Spray, White
Vacuum Breaker (used w/ Spray)
Vacuum Breaker Cover Kit, White

Vacuum Breaker Cover Kit, Bone
Pedestal Cover Kit, White

Pedestal Cover Kit, Bone

10

500 PLUS SERIES PARTS LIST

MODEL 511+

MODEL 510+

Item

1

2

3
4
5
6

7
8

511+ 510+

385343829
385343831
385343897
385343901
385343899

385310739
385310740
385310741
385310742
385310743

385310048
385316140
385310064
385310108

385310109
385310110
385310600
385310603

600341549
385345889

385345892

385343765

307344653

385343829
385343831
385343897
385343901
385343899

385310739
385310740
385310741
385310742
385310743

385310048
385316140
385310064

385310111
385310112
385310113
385310173
385310203

600341549
385345889

385345892

385343765

307344653

Description

Seat Assembly, White
Seat Assembly, Bone
Seat Assembly, Platinum
Seat Assembly, Ebony
Seat Assembly, Teal

China Bowl Kit, White
China Bowl Kit, Bone
China Bowl Kit, Platinum
China Bowl Kit, Ebony
China Bowl Kit, Teal

Band Clamp & Half Clamp Kit

®

Teflon

& Rubber Seal Kit
Mounting Bolt Kit
Pedestal Cover Kit, White

Pedestal Cover Kit, Bone
Pedestal Cover Kit, Platinum
Pedestal Cover Kit, Ebony
Pedestal Cover Kit, Teal

Floor Flange Seal
Floor Flange, 3" MPT

(sold separately)
Floor Flange, 3" Socket
(sold separately)
Floor Flange, 3" Spigot
(sold separately)
Floor Flange Adapter, 45º
Swivel (sold separately)

Item

9

10

11
12
13

14*

15
16

16A

17
18

11

385318162

385310177
385310188

385310117
385310118
385310119
385310593
385310596

385314349
385236096
600340825

385310744
385310123

385310124
385310125
385310588
385310620

600340177
385316906
385230335

385319054
600340683

600341770

385318162

385310177
385310188

385310114
385310115
385310116
385310175
385310193

385314349
385236096
600340873

385310578
385310120

385310121
385310122
385310169
385310198

600340177
385316906
385230335

385319054
600340683

600341770

Description511+ 510+

Ball/Shaft/Cartridge Kit,
White/Bone/Platinum
Ball/Shaft/Cartridge Kit, Ebony
Ball/Shaft/Cartridge Kit, Teal

Pedal Cover Kit, White
Pedal Cover Kit, Bone
Pedal Cover Kit, Platinum
Pedal Cover Kit, Ebony
Pedal Cover Kit, Teal

Water Valve Kit
Spring Cartridge Assembly
Flush Lever

Flush Lever/Spring Cartridge Ass’y.
Base Kit, White

Base Kit, Bone
Base Kit, Platinum
Base Kit, Ebony
Base Kit, Teal

Supply Hose
Vacuum Breaker Kit
Vacuum Breaker Kit (used with

Hand Spray)
Vacuum Breaker w/ Hand Spray Kit
Hand Spray, White

Hand Spray, Ebony

* includes items
3 – 7, 9 – 13

2000 SERIES PARTS LIST

MODEL 2011

MODEL 2010

Item

1

2

3
3A
3B

3C

4

5

6

7

8

9

2011 2010

385344436
385344437
385344438

385310615
385310616
385310585

385316906
385319054
600340683

600341770
385230335

600340177
385310048
385316140
385318162

385310177
385236096
385310117

385310118
385310593

385344436
385344437
385344438

385310615
385310616
385310585

385316906
385319054
600340683

600341770
385230335

600340177
385310048
385316140
385318162

385310177
385236096
385310114

385310115
385310175

Description

Seat Assembly, White
Seat Assembly, Bone
Seat Assembly, Ebony

China Bowl Kit, White
China Bowl Kit, Bone
China Bowl Kit, Ebony

Vacuum Breaker Kit
Vacuum Breaker with Spray Kit
Hand Spray, White

Hand Spray, Ebony
Vacuum Breaker (used with

Hand Spray)
Supply Hose, Bone
Band Clamp & Half Clamp Kit

®

& Rubber Seal Kit

Teflon
Ball/Shaft/Cartridge Kit,

White/Bone
Ball/Shaft/Cartridge Kit, Ebony

Spring Cartridge Assembly
Pedal Cover Kit, White

Pedal Cover Kit, Bone
Pedal Cover Kit, Ebony

Item Description

10

12 *

13

14
15
16

2011 2010

385314349
600340825

11

385310579
385310123

385310124
385310588

385310108
385310109
385310600

600341549
385310064
385345889

385345892

385343765

307344653

385314349
600340873

385310578
385310120

385310121
385310169

385310111
385310112
385310173

600341549
385310064
385345889

385345892

385343765

307344653

Water Valve Kit
Flush Lever

Flush Lever & Spring Cartridge Kit
Base Kit, White

Base Kit, Bone
Base Kit, Ebony

Pedestal Cover Kit, White
Pedestal Cover Kit, Bone
Pedestal Cover Kit, Ebony

Floor Flange Seal
Mounting Bolt Kit
Floor Flange, 3" MPT

(sold separately)
Floor Flange, 3" Socket
(sold separately)
Floor Flange, 3" Spigot
(sold separately)
Floor Flange Adapter, 45º Swivel
(sold separately)

* includes items
5 – 11, 13 – 15

12

DIMENSIONAL SPECIFICATIONS

*

MODEL 111

* Width measurement includes flush pedal.

*

MODEL 511+

* Width measurement includes flush pedal.

MODEL 110

MODEL 510+

*

MODEL 2011

* Width measurement includes flush pedal.

MODEL 2010

All dimensions may vary ± 3/8-inch (10mm).

13

ORDERING PARTS

Dometic is ready to assist you in the event service is required. Before calling, please have the following information
available. Your cooperation in having this information ready is appreciated and allows us to better meet your needs.

1. Toilet Model Number

2. Serial Number

3. Part Number, Description and Quantity (see Parts List)

CUSTOMER SERVICE

There is a strong, worldwide network to assist in servicing and maintaining your sanitation system. For the
Authorized Service Center near you, please call from 8:00 a.m. to 5:00 p.m. (ET) Monday through Friday.

Telephone: [phone] U.S.A. and Canada

330-496-3211 International

Email: [e-mail]

You can also contact the Parts Distributor in your area for quick response to your replacement parts needs. They carry
a complete parts inventory for this SeaLand product line.

Fax: [phone] U.S.A. and Canada

330-496-3220 International

U.S.A. SEALAND MASTER SANITATION DISTRIBUTORS

U.S.A. – North Central
(IL, IN, KY, MI, OH)

Midwest Marine Supply
24300 Jefferson Ave.
St. Clair Shores, MI 48080
Tel: [phone]

800-860-1540
Fax: [phone]
Email: [e-mail]
Contact: Bob Kennedy

U.S.A. - Northeast
(CT, DE, DC, MA, MD, ME, NH,
NJ, NY, PA, RI, VA, VT, WV)

Northeast Marine Sanitation
69 Florida Street
Farmingdale, NY 11735
Tel: [phone]

800-352-4323

Fax: [phone]

888-283-7606
E-mail: northeast@
northeastsanitation.com
Contact: Mike Starito

U.S.A. - Northwest
(AK, ID, MT, OR, WA, WY)

Marine Sanitation, Inc.
1900 N. Northlake Way, Suite 121
Seattle, WA 98103
Tel: [phone]

800-624-9111
Fax: [phone]
E-mail: marinesan@

mindspring.com

Contact: Ric Kolb

U.S.A. - South Central
(AR, KS, LA, MO, MS, NM, OK, TX)

AER Supply
P.O. Box 349
2301 Nasa Road #1
Seabrook, TX 77586
Tel: [phone]

800-767-7606
Fax: [phone]
E-mail: [e-mail]
Contact: Richard Miller

U.S.A. - Southeast
(AL, FL, GA, NC, PR, SC, TN, VI)

Environmental Marine Service
111 S.W. 23rd Street, Suite A
Fort Lauderdale, FL 33315
Tel: [phone]

800-522-2656
Fax: [phone]
E-mail:
[e-mail]
Contact: John or Jill Hopkins

U.S.A. - Southwest
(AZ, CO, NV, UT, CA-south)

Ardemco Marine Specialties
778 West 17th Street
Costa Mesa, CA 92627
Tel: [phone]

800-253-0115
Fax: [phone]
E-mail: [e-mail]
Contact: Rick Glasser

14

U.S.A. – Upper Midwest
(IA, MN, ND, NE, SD, WI)

PowerHouse Marine
518 Logan
La Crosse, WI 54603
Tel: [phone]

888-752-4539
Fax: [phone]
E-mail:
[e-mail]
Contact: Dave Tucker

U.S.A. – Northern California

Fox Marine
2250 Zanker Road, Unit D
San Jose, CA 95131
Tel: [phone]

800-826-2873
E-mail: [e-mail]
Contact: Charlie Barker

CANADA DISTRIBUTORS

Canada – East

Eastern Marine Systems, Inc.
12-A Leslie Street
Toronto, Ontario M4M 3H7
Tel: [phone]

888-764-1111
Fax: [phone]
E-mail: [e-mail]
Contact: Paul Gales

Canada – West

Western Marine Company
1494 Powell Street
Vancouver, BC V5L 5B5
Tel: [phone]

800-663-0600
Fax: [phone]

800-663-6790
E-mail: [e-mail]
Contact: Bill Falk

NOTES

15

MANUFACTURER’S THREE-YEAR AND TEN-YEAR LIMITED WARRANTIES

Dometic Corporation warrants, to the original purchaser only, that this Traveler® gravity discharge toilet, if used for
personal, family or household-like purposes, is free from defects in material and workmanship for a period of three (3)
years from the date of purchase.

Dometic also warrants, to the original purchaser only, that the ceramic portion of the toilet bowl will not discolor, stain,
scratch or craze for a period of ten (10) years if used for personal, family or household-like purposes, and is regularly
cleaned as described in the product’s owner’s manual.

If this Dometic product is placed in commercial or business use, it will be warranted, to the original purchaser only, to be
free of defects in material and workmanship for a period of ninety (90) days from the date of purchase.

Dometic reserves the right to replace or repair any part of this product that proves, upon inspection by Dometic, to be
defective in material or workmanship. All labor and transportation costs or charges incidental to warranty service are to
be borne by the purchaser-user.

EXCLUSIONS

IN NO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, FOR DAMAGES
RESULTING FROM IMPROPER INSTALLATION, OR FOR DAMAGES CAUSED BY NEGLECT, ABUSE, ALTER­ATION, OR USE OF UNAUTHORIZED COMPONENTS. THIS INCLUDES FAILURES WHICH MAY RESULT FROM
NOT FOLLOWING THE WINTERIZATION OR CLEANING PROCEDURES AS DESCRIBED ON PAGE 5 OF THIS
OWNER’S MANUAL. ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF ONE (1) YEAR FROM DATE OF
PURCHASE.

IMPLIED WARRANTIES

No person is authorized to change, add to, or create any warranty or obligation other than that set forth herein.

Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from
the date of purchase for products used for personal, family or household-like purposes, and ninety (90) days from the
date of purchase for products placed in commercial or business use.

OTHER RIGHTS

Some states do not allow limitations on the duration of an implied warranty, and some states do not allow exclusions
or limitations regarding incidental or consequential damages; so, the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may have other rights which vary from state to state.

To obtain warranty service, first contact your local dealer from whom you purchased this product.

340098 8/03

Dometic Corporation

13128 State Rt. 226, P.O. Box 38

Big Prairie, OH 44611-0038 USA

SeaLand Product Hotline [phone]

(8:00 a.m. - 5:00 p.m. ET)

® Registered; ™ Trademark of Dometic Corporation

® Bar Keepers Friend is a trademark of Servaas Laboratories.

® Teflon is a registered trademark of Du Pont Co.

 Dometic Corporation

16