SeaLand 510+, 511+, 2011, 2010 Owner's Manual

Page 1
®
SeaLand
GRAVITY DISCHARGE TOILET
OWNER’S MANUAL
SeaLand® 500 Plus Series, 2000 Series,
Model 111 Toilet
WARNING
!
This manual must be read and under­stood before installation, adjustment, service, or maintenance is performed.
Modication of this product can result
in property damage.
13128 State Rt 226, PO Box 38
Big Prairie, OH 44611
SeaLand Product Customer Service: 1-800-321-9886
www.DometicUSA.com
1
Page 2
TABLE OF CONTENTS
Important Information .............................................2
Toilet Model Identication ...................................... 2
How to Use ............................................................. 2
Installation ..............................................................3
Pedestal and Pedal Cover Installation .................. 3
Proper Bowl Cleaning ............................................ 4
Winterizing ............................................................. 4
Dimensional Specications..................................... 4
Deodorants and Special Tissue .............................5
Service Tip .............................................................5
Troubleshooting Guide ......................................6 - 7
Ordering Parts ........................................................ 8
Customer Service ................................................... 8
Warranty ................................................................. 8
IMPORTANT INFORMATION
1. Do not use chlorine or caustic chemicals, such as laundry bleach or drain-opening types, in the system. These products damage the seals in toilets and dump valves.
2. Do not permit foreign objects (paper towels, paper cups, diapers, sanitary napkins, etc.) to be ushed through the toilet.
3. Mechanical seal toilets, like SeaLand units, are designed to only discharge directly into a holding tank. Horizontal pipe runs as found in conventional residential or commercial plumbing systems cannot be
accommodated.
4. Toilet must be regularly cleaned and winterized according to “Proper Bowl Cleaning” and “Winterizing” procedures on page 4, or your warranty coverage may be voided.
TOILET MODEL IDENTIFICATION
The model identication label is located on the toilet base and will show the model number and serial number. Follow
instructions for removing toilet pedestal cover in “Pedestal
and Pedal Cover Installation” on page 3. If label is not available, please refer to “Dimensional Specications” on page 4 for toilet model identication.
HOW TO USE
To prepare the SeaLand toilet for use, make sure water supply to the toilet is connected. Turn on water supply and check system for leaks. Flush toilet and check again for leaks.
Make sure the ushing instruction label (shown at right) is in plain sight and easy for
guests to read. If this label is not included in this manual, please contact the SeaLand Product Customer Service Department immediately.
To properly use the SeaLand toilet, follow these simple instructions:
1. To add water to the toilet, lift or raise the ush lever until desired
water level is reached. Generally, more water is required only when
ushing solids.
2. To ush toilet, push lever all the way down until contents leave toilet
bowl. Water ow pressures vary at different locations, therefore holding the ush lever down for 4-8 seconds may be required. We require a minimum ow at the inlet of the toilet of 2 gpm (7.6 lpm) for proper ushing.
3. Allow ush lever to snap back, which permits positive sealing around the ush ball.
4. A small amount of water should remain in bowl.
Note: Holding ush lever down longer than necessary results in excessive water usage.
2
Page 3
INSTALLATION
1. To replace an older toilet, turn off water supply to toilet. Disconnect water line
at toilet water valve. Unscrew oor bolt nuts and remove toilet. Discard old oor seal and mounting bolts. The old oor ange may be used if it is in good condition and has fastener holes that are positioned correctly. Make sure center of oor ange is at least 11 inches (279 mm) from back wall (Figure A).
NOTE: If old oor ange cannot be used and cannot be removed, please use
a SeaLand Universal Mounting Kit, available from your SeaLand dealer.
2. When installing new oor ange, make certain that the toilet mounting bolts align
properly with SeaLand toilet mounting pattern.
3. Secure ange to oor using at head screws through countersunk holes in ange. Insert oor bolts into slotted holes in ange (Figure B).
4. If toilet is being installed in a shower stall, apply a 1/4" thick by 3/4" wide bead of glazing compound around the circumference of the oor ange (Figure C).
5. SeaLand toilet models 111, 510 and 511 will accept handicap or household deco­rative seats. Remove existing seat and replace with new seat if desired.
6. Position oor seal by pressing the oor bolts up through holes in the seal.
7. Set toilet in place with bolts protruding up through mounting holes in base (Figure D).
8. Install washers and hex nuts provided with toilet. Tighten nuts down equally with
standard 7/16" open end wrench. Remove excess glazing compound from around base in shower stall installation.
9. Connect water supply line to water valve (1/2" MPT) inlet using appropriate ttings or an extension (Figure E).
10. Turn on water supply and ush toilet to test for leaks.
11. Attach pedestal and pedal covers to toilet base (see instructions below).
Fig. A
Fig. B
Fig. C
Fig. D
PEDESTAL AND PEDAL COVER INSTALLATION
1. Wrap pedestal cover
around base so that
it closes as shown.
2. Tall model – screw cover together. Short model – snap together.
3. Slide pedal cover onto foot pedal rod.
Fig. E
4. Secure side plate onto pedal cover with screws.
3
Page 4
PROPER BOWL CLEANING
For stubborn stains, use SeaLand® Toilet Bowl Cleaner (Fig. A). It’s manufactured es­pecially for use with SeaLand toilets. In certain locations where water is hard, a build-up
Fig. A
of lime may dull the toilet bowl nish. Restore the shine with this SeaLand cleaner. If you cannot nd it in your area, contact Dometic for your nearest dealer. If the cleaner is not available, you can also use most non-abrasive bathroom and toilet bowl cleaners (Bar Keeper's Friend® spray cleaner, Clorox® toilet bowl cleaner, SaniFlush® toilet bowl cleaner, etc.). Please follow label instructions.
To avoid damaging the Teon®-coated seal, DO NOT USE:
– abrasives (Comet®, Soft Scrub® cleansers etc.) – caustic chemicals (Drano® clog remover, etc.) – lubricants and cleaners containing alcohols or petroleum distillates (Pam® cooking spray, Pine-Sol® cleaner, WD-40® lubricant, etc.).
® Bar Keepers Friend is a registered trademark of SerVaas Laboratories Inc. ® Clorox, Pine-Sol and Soft Scrub are registered trademarks of The Clorox Co. ® Comet is a registered trademark of Prestige Brands International. ® Drano is a registered trademark of S.C. Johnson & Son Inc.
® Pam is a registered trademark of ConAgra Foods. ® Sani-Flush is a registered trademark of Reckitt Benckiser Inc. ® Teon is a registered trademark of DuPont Co. ® WD-40 is a registered trademark of WD-40 Company.
WINTERIZING
At the end of each season, the SeaLand toilet should be winterized for storage, by either draining or using potable water-safe antifreeze in the system.
To drain:
1. Thoroughly ush system with fresh water.
2. Empty holding tank.
3. Shut off water supply to toilet(s), and remove inlet waterline (Fig. B).
Do not remove brass cap on bottom of valve.
4. Press ush lever until all water is drained from toilet(s).
To use antifreeze:
1. Drain potable water tank.
2. Add freshwater antifreeze to potable water tank.
3. Flush potable wate r antifreeze and water mixture thr ough toilet(s ) and in to the waste holding tank. Each
installation is different, so amounts may vary. User discretion is required to assure adequate protection.
4. Empty holding tank. Use nontoxic antifreeze designated for potable water systems. (See vehicle owner’s manual.)
NOTE: CAUTION: Never use automotive-type antifreeze in freshwater systems.
Fig. B
DIMENSIONAL SPECIFICATIONS
*
*
MODEL 511+
*
MODEL 2011
* Width measurement includes ush pedal.
All dimensions may vary
± 3/8-inch (10mm).
MODEL 510+
MODEL 111
MODEL 2010
4
Page 5
DEODORANTS AND SPECIAL TISSUE
SeaLand toilets require the regular addition of a deodorant product to reduce holding tank malodors and to help break down holding tank contents. Several factors should be considered in selecting a deodorant product.
Liquid or Granulated: Liquid products obviously work more quickly by readily going into solution. Granulated powder formulations, on the other hand, have the advantage of requiring less storage space and are less likely to leak if the package is inadvertently damaged.
Formaldehyde versus Non-Formaldehyde: Dometic manufactures both types of deodorants. Generally speak- ing, formaldehyde formulas control odor very effectively at all temperatures and with all degrees of water hardness. SeaLand Environment-Friendly brand, which is formaldehyde-free, is similarly effective.
How Much Deodorant and How to Add It: The deodorant is added directly into the toilet bowl, then ushed into the holding tank. Follow bottle or package instructions. Conditions of extremely warm weather, longer waste hold­ing time and larger tank capacities may require more deodorant treatment. Also, to maintain optimum efciency in odor control, the waste holding tank should be cleaned thoroughly at least once or more each season depending
on use.
Why Not Use Household Toilet Paper in Your SeaLand Toilet. Household tissues often contain adhesives which
bond together the paper bers from which the tissue is made. The adhesives prevent the tissue from breaking apart, and their use in “ultra-low ow” systems can cause system clogging. SeaLand tissue is especially designed for use in low water toilet systems. Its rapid dissolving properties minimize the amount of residual paper in the holding tank and allow deodorizers to work more efciently.
SeaLand Brand versus Other Brands: We constantly strive to provide our system owners with effective products that have minimal environmental impact and good value. Many deodorant products do not measure up to our stan­dards of performance and value.
SeaLand® Liquid
Deodorant -
Environment
Friendly
32-oz. bottle
Part No.
379114032
SeaLand®
Granulated
Deodorant
Six 2-oz. pouches
379626002
Part No.
SeaLand®
Clean ‘n Green
Bowl Cleaner &
Tank Deodorant
12-2 oz. drop-in
pouches
Part No. 379512602
SeaLand®
Cleaner
16-oz. bottle
Part No.
379314016
SeaLand®
Rapid-Dissolving
Toilet Tissue
Four 400-sheet rolls
Part No.
379441204
SeaLand® Liquid
Deodorant
Two 8-oz. bottles
Part No.
379224008
SERVICE TIP
Checking for water leaks behind or under toilets or other appliances can make it difcult to locate the source. Drip­ping water at room temperature makes it difcult to feel wetness. Taking four or ve sheets of toilet tissue and wiping all seams and waterline connections offers a simple means of locating the general area of the leakage. Start at the top of the unit since gravity will cause a leak to run downward. When the tissue comes in contact with the leaking
water, it will immediately change texture.
5
Page 6
TROUBLESHOOTING GUIDE
SEALAND TOILET
BASE ASSEMBLY
WATER VALVE ASSEMBLY
TOP VALVE CAP
FILTER SCREEN
PEDAL COVER
TOILET BOWL, REAR VIEW
(Models 510+, 511+, 2010, 2011)
WHITE CAP
VACUUM
BREAKER
ADJUSTING NUT
CAM STRAP
VALVE BODY
WATER VALVE SCREWS
HOSE
CONNECTION
SPRING CARTRIDGE
BALL SEAL
BOWL SEAL
BAND CLAMP
FLUSH BALL
SHAFT
MODEL 111 TOILET BOWL, REAR VIEW
VACUUM
BREAKER
HOSE
CONNECTION
VACUUM BREAKER/BOWL CONNECTION
VACUUM BREAKER/BOWL CONNECTION
Problem Possible Cause Service Instructions
1. Toilet emits odor (ush ball open).
2. Water will not stay in bowl.
a. Odor emitting from base of toilet. b. Plugged holding tank vent line.
a. Loose band clamp. b. Improper seal around ush ball due to dirt or debris on ush ball.
c. Worn or damaged seal.
d. Worn or damaged ush ball.
3. Flush ball will not close
completely.
a. Too much friction between ush
ball and seal.
b. Water valve screws are too tight.
c. Defective spring cartridge.
® Pledge is a registered trademark of S.C. Johnson & Son Inc.
a. Use SeaLand brand deodorants. b. Clear obstruction from vent line.
a. Tighten adjusting screw. b. Inspect ush ball and seal for
foreign debris. Clean ush ball
and seal if needed.
c. Replace seal.
d. Replace ush ball.
a. Lubricate between ush ball and
seal with furniture polish (e.g.
Pledge® furniture polish).
b. Loosen screws slightly. c. Check spring tension by pushing
ush lever down, then release it
suddenly. If lever does not snap
back to original position, replace
spring cartridge.
6
Page 7
TROUBLESHOOTING GUIDE (cont'd)
Problem Possible Cause Service Instructions
4. Flush ball will not open.
a. Broken shaft. b. Shaft not fully engaged in the
spring cartridge.
a. Replace shaft.
b. Put pressure on shaft from under
the ush ball (pushing into spring cartridge) until it engages. You may have to rotate ush ball
slightly until shaft lines up with square in spring cartridge.
5. Flush ball does not open
completely. Applies to short-base units mounted on step or riser only.
6. Water does not shut off in
toilet (toilet overows).
7. Hand spray unit leaks.
8. Water does not enter toilet
bowl properly.
9. Water is leaking from
water valve.
a. Floor ange interferes with ush
ball rotation.
a. Not enough clearance between
cam strap and top of water valve cap.
b. Dirt lodged in water valve seal.
c. Worn or defective water valve. d. Worn or defective spring cartridge.
a. Hand sprayer is defective.
a. Insufcient water ow rate at toilet.
b. Water valve clogged.
c. Plugged rim wash holes in toilet.
a. Water valve body cracked due to
freeze damage.
b. Water line connection is loose or
not seated properly. c. Defective water valve. d. Stripped threads.
a. Loosen mounting bolts and push
toilet base back. If this does not solve problem, install a SeaLand Universal Mounting Kit (part no. 310139, 310140, or 310141) with existing oor ange.
a. Adjust cam strap to have .02"
- .06" (.5mm - 1.5mm) clearance
with top of water valve cap.
b. Dissassemble and clean water
valve. c. Replace water valve. d. Replace spring cartridge.
a. Replace hand sprayer.
a. Check water ow rate at toilet.
Rate should be 2 gpm (7.6 lpm)
at toilet. b. Remove and clean screen
located at inlet of water valve.
c. Clean holes. If still a problem,
replace the toilet bowl.
a. Replace water valve.
b. Insure that threads are not cross-
threaded and tighten. c. Replace water valve. d. Replace water valve.
10. Water is leaking from bottom of toilet base.
11. Water is leaking from rear of toilet bowl.
12. Water is leaking from the base/toilet connection.
a. Toilet is not secured to oor. b. Worn or defective toilet mounting
oor seal. c. Cracked base. d. Worn or defective oor ange.
a. Worn or defective vacuum
breaker.
b. Loose vacuum breaker.
c. Cracked or defective toilet bowl.
a. Band clamp may be loose.
b. Ball/bowl seal may be worn
or defective.
7
a. Tighten toilet mounting bolts. b. Replace oor seal between oor
ange and toilet base. c. Replace base assembly. d. Replace oor ange.
a. Remove white cap from vacuum
breaker. Flush toilet. If water
leaks during ush, vacuum
breaker needs to be replaced. b. Secure vacuum breaker
connection. If loose, push
breaker into bowl. c. Replace toilet bowl.
a. Remove plastic base cover and
tighten the band clamp. b. Replace ball/bowl seal.
Page 8
ORDERING PARTS
Dometic is ready to assist you in the event service is required. Before calling, please have the following informa-
tion available. Your cooperation in having this information ready is appreciated and allows us to better meet your
needs.
1. Toilet Model Number
2. Serial Number
3. Part Number, Description and Quantity (see separate Parts List)
CUSTOMER SERVICE
There is a strong, worldwide network to assist in servicing and maintaining your sanitation system. For the Authorized Service Center near you, please call from 8:00 a.m. to 5:00 p.m. (ET) Monday through Friday.
Telephone: 1-800-321-9886 U.S.A. and Canada 330-496-3211 International
Fax: 330-496-3097 U.S.A. and Canada 330-496-3220 International
Email: sealand@dometicusa.com
MANUFACTURER’S TWO-YEAR AND TEN-YEAR LIMITED WARRANTIES
Dometic Corporation warrants, to the original purchaser only, that this SeaLand® gravity discharge toilet, if used for personal,
family or household-like purposes, is free from defects in material and workmanship for a period of two (2) years from the date
of purchase.
Dometic also warrants, to the original purchaser only, that the ceramic portion of the toilet bowl will not discolor, stain, scratch or craze for a period of ten (10) years if used for personal, family or household-like purposes, and is regularly cleaned as described in the product’s owner’s manual.
If this Dometic product is placed in commercial or business use, it will be warranted, to the original purchaser only, to be free of defects in material and workmanship for a period of ninety (90) days from the date of purchase.
Dometic reserves the right to replace or repair any part of this product that proves, upon inspection by Dometic, to be defective in material or workmanship. All labor and transportation costs or charges incidental to warranty service are to be borne by the
purchaser-user.
EXCLUSIONS
IN NO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, FOR DAMAGES RESULTING FROM IMPROPER INSTALLATION, OR FOR DAMAGES CAUSED BY NEGLECT, ABUSE, ALTERATION, OR USE OF UNAUTHORIZED COMPONENTS. THIS INCLUDES FAILURES WHICH MAY RESULT FROM NOT FOLLOWING THE WINTERIZATION OR CLEANING PROCEDURE AS DESCRIBED IN THIS OWNER’S MANUAL. ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OF ONE (1) YEAR FROM DATE OF PURCHASE.
IMPLIED WARRANTIES
No person is authorized to change, add to, or create any warranty or obligation other than that set forth herein.
Implied warranties, including those of merchantability and tness for a particular purpose, are limited to one (1) year from the date of purchase for products used for personal, family or household-like purposes, and ninety (90) days from the date of purchase for products placed in commercial or business use.
OTHER RIGHTS
Some states do not allow limitations on the duration of an implied warranty, and some states do not allow exclusions
or limitations regarding incidental or consequential damages; so, the above limitations may not apply to you. This warranty gives you specic legal rights, and you may have other rights which vary from state to state.
To obtain warranty service, rst contact your local dealer from whom you purchased this product.
Dometic is a customer-driven, world-leading provider of innovative leisure
products for the caravan, motorhome and marine markets. Dometic offers a complete range of air conditioners, refrigerators, awnings, cookers,
sanitation systems, lighting, windows, doors and other equipment that
makes leisure life more comfortable away from home.
Dometic also provides refrigerators for specic use in hotel rooms, ofces and for storage of medical products and wine. Dometic’s products are sold in almost 100 countries and are produced mainly in Dometic’s
own production facilities around the world. Dometic has more than 4,400 employees.
600340098 3/07
13128 State Rt 226, PO Box 38
Big Prairie, OH 44611
SeaLand Product Customer Service: 1-800-321-9886
Email: SeaLand@DometicUSA.com
www.DometicUSA.com
® Registered; ™ Trademark of Dometic Corporation
Dometic Corporation
8
Loading...