SeaLand 111 User Manual

®

SeaLand

GRAVITY DISCHARGE TOILET

OWNER’S MANUAL

SeaLand® 500 Plus Series, 2000 Series,

Model 111 Toilet

WARNING

!

This manual must be read and under­stood before installation, adjustment,
service, or maintenance is performed.

Modication of this product can result

in property damage.

Dometic Sanitation Corporation

13128 State Rt 226, PO Box 38

Big Prairie, OH 44611

SeaLand Product Customer Service: 1-800-321-9886

(8:00 a.m. - 5:00 p.m. ET)

1

TABLE OF CONTENTS

Important Information .............................................2

Toilet Model Identication ...................................... 2

How to Use ............................................................. 2

Installation ..............................................................3

Pedestal and Pedal Cover Installation .................. 3

Proper Bowl Cleaning ............................................ 4

Winterizing ............................................................. 4

Dimensional Specications..................................... 4

Deodorants and Special Tissue .............................5

Service Tip .............................................................5

Troubleshooting Guide ......................................6 - 7

Ordering Parts ........................................................ 8

Customer Service ................................................... 8

Warranty ................................................................. 8

IMPORTANT INFORMATION

1. Do not use chlorine or caustic chemicals, such as laundry bleach or drain-opening types, in the system. These
products damage the seals in toilets and dump valves.

2. Do not permit foreign objects (paper towels, paper cups, diapers, sanitary napkins, etc.) to be ushed through
the toilet.

3. Mechanical seal toilets, like SeaLand units, are designed to only discharge directly into a holding
tank. Horizontal pipe runs as found in conventional residential or commercial plumbing systems cannot be

accommodated.

4. Toilet must be regularly cleaned and winterized according to “Proper Bowl Cleaning” and
“Winterizing” procedures on page 4, or your warranty coverage may be voided.

TOILET MODEL IDENTIFICATION

The model identication label is located on the toilet base
and will show the model number and serial number. Follow

instructions for removing toilet pedestal cover in “Pedestal

and Pedal Cover Installation” on page 3. If label is not
available, please refer to “Dimensional Specications” on
page 4 for toilet model identication.

DOMETIC CORPORATION

P.O. BOX 38, 13128 STATE RT 226 [phone]
BIG PRAIRIE, OH 44611 USA

MODEL NO. 000

SERIAL NUMBER

000000

HOW TO USE

To prepare the SeaLand toilet for use, make sure water supply to the toilet
is connected. Turn on water supply and check system for leaks. Flush toilet
and check again for leaks.

Make sure the ushing instruction label (shown at right) is in plain sight and easy for

guests to read. If this label is not included in this manual, please contact the
SeaLand Product Customer Service Department immediately.

To properly use the SeaLand toilet, follow these simple instructions:

1. To add water to the toilet, lift or raise the ush lever until desired

water level is reached. Generally, more water is required only when
ushing solids.

2. To ush toilet, push lever all the way down until contents leave toilet

bowl. Water ow pressures vary at different locations, therefore holding the ush lever down for 4-8 seconds
may be required. We require a minimum ow at the inlet of the toilet of 2 gpm (7.6 lpm) for proper ushing.

3. Allow ush lever to snap back, which permits positive sealing around the ush ball.

4. A small amount of water should remain in bowl.

Note: Holding ush lever down longer than necessary results in excessive water usage.

2

INSTALLATION

1. To replace an older toilet, turn off water supply to toilet. Disconnect water line
at toilet water valve. Unscrew oor bolt nuts and remove toilet. Discard old
oor seal and mounting bolts. The old oor ange may be used if it is in good
condition and has fastener holes that are positioned correctly. Make sure center
of oor ange is at least 11 inches (279 mm) from back wall (Figure A).

NOTE: If old oor ange cannot be used and cannot be removed, please use

a SeaLand Universal Mounting Kit, available from your SeaLand dealer.

2. When installing new oor ange, make certain that the toilet mounting bolts align
properly with SeaLand toilet mounting pattern.

3. Secure ange to oor using at head screws through countersunk holes in ange.
Insert oor bolts into slotted holes in ange (Figure B).

4. If toilet is being installed in a shower stall, apply a 1/4" thick by 3/4" wide bead of
glazing compound around the circumference of the oor ange (Figure C).

5. SeaLand toilet models 111, 510 and 511 will accept handicap or household deco­rative seats. Remove existing seat and replace with new seat if desired.

6. Position oor seal by pressing the oor bolts up through holes in the seal.

7. Set toilet in place with bolts protruding up through mounting holes in base
(Figure D).

8. Install washers and hex nuts provided with toilet. Tighten nuts down equally with
standard 7/16" open end wrench. Remove excess glazing compound from around
base in shower stall installation.

9. Connect water supply line to water valve (1/2" MPT) inlet using appropriate ttings
or an extension (Figure E).

10. Turn on water supply and ush toilet to test for leaks.

11. Attach pedestal and pedal covers to toilet base (see instructions below).

Fig. A

Fig. B

Fig. C

Fig. D

PEDESTAL AND PEDAL COVER INSTALLATION

1. Wrap pedestal cover

around base so that

it closes as shown.

2. Tall model – screw
cover together.
Short model –
snap together.

3. Slide pedal cover
onto foot pedal rod.

Fig. E

4. Secure side plate
onto pedal cover
with screws.

3