Seagate ST9160316AS, ST9250310AS, ST9400321AS, ST9500320AS, ST9640320AS User Manual

...

Product Manual

Momentus

512-byte sector models

ST9640320AS ST9500320AS ST9320310AS ST9250310AS ST9160316AS

4096-byte sector models

ST9640322AS ST9400321AS ST9320312AS

100589392 Rev. D November 2010

Revision history

Revision Date Sheets affected or comments

Rev. A 10/14/09 Initial release. Rev. B 12/01/09 fc, 1, 3-6, 10-12 & 24.. Rev. C 04/27/10 fc, 1-2, 4-10, 15-16 and 27. Rev. D 11/30/10 28.

LLC in the United States and/or other countries. Momentus and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.

No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC. Call 877-PUB-TEK1 (877-782-8351) to request permission.

One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer's operating system may use a different standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage. Seagate reserves the right to change, without notice, product offerings or specifications.

Contents

1.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.2.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.4 Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.5 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.6 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.7 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.8 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.9 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.9.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.9.2 Deferred spinup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.9.3 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.9.4 Voltage tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.9.5 Power-management modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.10 Environmental specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.10.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.10.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.10.3 Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.10.4 Altitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.10.5 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.10.6 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.11 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.12 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.13 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.14 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.14.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.14.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.14.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.15 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.15.1 European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 18

3.15.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 18

3.16 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.3 Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.0 Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.3.1 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.3.3 S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Momentus Product Manual, Rev. D i

ii Momentus Product Manual, Rev. D

List of Figures

Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 4. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Momentus Product Manual, Rev. D iii

1.0 Seagate Technology support services

SEAGATE ONLINE SUPPORT and SERVICES

For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/

Available services include:

Presales & Technical support Global Support Services telephone numbers & business hours Authorized Service Centers

For information regarding Warranty Support, visit

http://www.sea

For information regarding Data Recovery Services, visit http://www.i365.com For Seagate OEM & Distribution partner portal, visit https://direct.seagate.com/portal/system For Seagate reseller portal, visit http://spp.seagate.com

gate.com/www/en-us/support/warranty_&_returns_assistance

Momentus Product Manual, Rev. D 1

2.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus

model drives:

4K byte/sector models

• ST9640322AS • ST9400321AS • ST9320312AS

512 byte/sector models

• ST9640320AS • ST9320310AS • ST9160316AS

• ST9500320AS • ST9250310AS •

These drives provide the following key features:

• 5400-RPM spindle speed.

• 8-MB buffer.

• Quiet operation. Fluid Dynamic Bearing (FDB) motor.

• High instantaneous (burst) data-transfer rates (up to 3.0 Gb/s).

• Perpendicular recording technology provides the drives with increased areal density.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Native Command Queuing (NCQ) with command ordering.

• Full-track multiple-sector transfer capability without local processor intervention.

• 1000 Gs nonoperating shock and 350 Gs of operating shock.

• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• The 3D Defense System™, which includes Drive Defense, Data Defe nse and Diagnostic Defense, of fers the industry’s most comprehensive protection for disc drives.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

2 Momentus Product Manual, Rev. D

2.1 About the Serial ATA interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:

• Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set any jumpers or other configuration op tio ns .

• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.

• Scalability to higher performance levels.

In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current system and expect all of your existing applications to work as normal.

The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0 (master) devices.

Note. The host adapter may, optionally, emulate a master/slave environment to host software where two

devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA environment.

The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated.

The Serial ATA host adapter contains a set of registers that shadow the content s of the traditio nal devi ce registers, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. The specification can be downloaded from http://www.serialata.org.

Momentus Product Manual, Rev. D 3

3.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the Momentus models.

3.1 Specification summary table

The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.

Table 1: Drive specifications for 640, 500 and 400GB models

Drive specification ST9640322AS ST9640320AS ST9500320AS ST9400321AS

Formatted GB* 640 500 400 guaranteed logical blocks 1,250,263,728 976,773,168 781,422,768 bytes per physical sector 4096 512 512 4096 Physical read/write heads 4 Discs 2 Cache (MB) 8 Recording density in BPI (bits/in avg) 1560k Track density TPI (tracks/in avg) 325k Areal density (Gb/in Spindle speed (RPM) 5400 Average latency (ms) 5.2 Internal transfer rate (Mb/s max) 1175 I/O data transfer rate (MB/s max) 300 ATA data-transfer modes supported SATA 1.0, Serial ATA Revision 2.6

avg) 507

PIO modes 0–4 Multiword DMA modes 0–2 Ultra DMA modes 0–6

4 Momentus Product Manual, Rev. D

Table 1: Drive specifications for 640, 500 and 400GB models

Drive specification ST9640322AS ST9640320AS ST9500320AS ST9400321AS

Seek power (typical) 1.3W Read/write power (typical) Read: 1.25W; Write: 1.65W Idle mode, low power (typical) 0.47W Standby mode 0.12W (typical)*** Sleep mode 0.12W (typical)*** Voltage tolerance (including noise) +5V ± 5% Ambient temperature 0° to 60°C (operating), –40° to 70°C (nonoperating) Temperature gradient

(°C per hour max) Relative humidity 5% to 95% (operating)

Relative humidity gradient 30% per hour max Wet bulb temperature

(°C max) Altitude, operating –304.8 m to 3048 m (–1000 ft to 10,000 Altitude, nonoperating

(meters below mean sea level, max) Shock, operating (Gs max at 2ms) 350 Shock, nonoperating (Gs max at 1ms) 1000 Shock, nonoperating (Gs max at 0.5ms) 1000 Vibration, operating 1.0 G (0 to peak, 5–500 Hz) Vibration, nonoperating 5.0 Gs (0 to peak, 5–500 Hz) Drive acoustics, sound power (bels) Idle** 2.3 (typical)

Seek 2.4 (typical)

Nonrecoverable read errors 1 per 10 Annualized Failure Rate (AFR) 0.48% Load/Unload (U/UL) cycles

25°C, 50% relative humidity

32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 10% relative humidity 55°C, 16% relative humidity

Warranty To determine the warranty for a specific drive, use a web browser to access the

Supports Hotplug operation per Serial ATA Revision 2.6 specification

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may incr ease acoustic and

power to operational levels.

***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby

modes will not contribute to battery power consumption.

20°C (operating) 35°C (nonoperating)

5% to 95% (nonoperating)

37.7 (operating) 40 (nonoperating)

ft)

–304.8 m to 12,192 m (–1000 ft to 40,000

2.5 (max)

2.6 (max)

bits read

600,000 software-controlled power on/off cycles 50,000 hard power on/off cycles

following web page:

http://www.sea

You will be asked to provide the drive serial number, model number (or part number) and country of purchase. After submitting this information, the system will display the warranty information for your drive.

Yes (requires COMRESET from host after a hotplug event)

gate.com/www/en-us/support/warranty_&_returns_assistance

ft)

Momentus Product Manual, Rev. D 5

Table 2: Drive specifications for 320, 250 and 160GB models

Drive specification ST9320312AS ST9320310AS ST9250310AS ST9160316AS

Formatted GB* 320 250 160 guaranteed logical blocks 625,142,448 488,397,168 312,581,808 bytes per physical sector 4096 512 512 512 Physical read/write heads 2 1 Discs 1 Cache (MB) 8 Recording density in BPI (bits/in avg) 1560k Track density TPI (tracks/in avg) 325k Areal density (Gb/in Spindle speed (RPM) 5400 Average latency (ms) 5.2 Internal transfer rate (Mb/s max) 1175 I/O data transfer rate (MB/s max) 300 ATA data-transfer modes supported SATA 1.0, Serial ATA Revision 2.6

Height 9.5 +/- 0.2 mm (0.374 +/-.008in) Width 69.85 mm +/- 0.25 mm (2.75 +/- 0.010in) Length 100.35 + 0.20 / - 0.25 mm (3.951 + 0.008 / - 0.010in) Weight <100 g (0.220 lb) Power-on to ready (sec typical) 3.6 Power-on to ready (sec max) 4.5 Standby to ready (sec typical) 2.5 Standby to ready (sec max) 3.5 Track-to-track seek time, read (ms typical) 1.5 Average seek, read (ms typical) 13.0 Full-stroke seek, read (ms max) 27.0 Startup current, +5V (max) 1.0A Seek power (typical) 1.3W Read/write power (typical) Read: 1.25W; Write: 1.65W Idle mode, low power (typical) 0.47W Standby mode 0.12W (typical)*** Sleep mode 0.12W (typical)*** Voltage tolerance (including noise) +5V ± 5% Ambient temperature 0° to 60°C (operating), –40° to 70°C (nonoperating) Temperature gradient

(°C per hour max) Relative humidity 5% to 95% (operating)

Relative humidity gradient 30% per hour max Wet bulb temperature

(°C max) Altitude, operating –304.8 m to 3048 m (–1000 ft to 10,000 Altitude, nonoperating

(meters below mean sea level, max) Shock, operating (Gs max at 2ms) 350

avg) 507

PIO modes 0–4 Multiword DMA modes 0–2 Ultra DMA modes 0–6

20°C (operating) 35°C (nonoperating)

5% to 95% (nonoperating)

37.7 (operating) 40 (nonoperating)

–304.8 m to 12,192 m (–1000 ft to 40,000

ft)

6 Momentus Product Manual, Rev. D

Table 2: Drive specifications for 320, 250 and 160GB models

Drive specification ST9320312AS ST9320310AS ST9250310AS ST9160316AS

Shock, nonoperating (Gs max at 1ms) 1000 Shock, nonoperating (Gs max at 0.5ms) 1000 Vibration, operating 1.0 G (0 to peak, 5–500 Hz) Vibration, nonoperating 5.0 Gs (0 to peak, 5–500 Hz) Drive acoustics, sound power (bels) Idle** 2.3 (typical)

Seek 2.4 (typical)

Nonrecoverable read errors 1 per 10 Annualized Failure Rate (AFR) 0.48% Load/Unload (U/UL) cycles

25°C, 50% relative humidity

32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 10% relative humidity 55°C, 16% relative humidity

Warranty To determine the warranty for a specific drive, use a web browser to access the

Supports Hotplug operation per Serial ATA Revision 2.6 specification

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may incr ease acoustic and

power to operational levels.

***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby

modes will not contribute to battery power consumption.

2.5 (max)

2.6 (max)

bits read

600,000 software-controlled power on/off cycles 50,000 hard power on/off cycles

following web page:

http://www.sea

Yes (requires COMRESET from host after a hotplug event)

gate.com/www/en-us/support/warranty_&_returns_assistance

Momentus Product Manual, Rev. D 7

3.2 Formatted capacity

Formatted

Model

ST9640322AS 640GB 1,250,263,728

ST9320312AS 320GB 625,142,448 ST9640320AS 640GB 1,250,263,728 ST9500320AS 500GB 976,773,168 ST9320310AS 320GB 625,142,448 ST9250310AS 250GB 488,397,168 ST9160316AS 160GB 312,581,808

*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

capacity*

Guaranteed logical blocks

Bytes per physical sector

4096ST9400321AS 400GB 781,422,768

512

3.2.1 LBA mode

When addressing these drives in LBA mode, all blocks (

sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed logical blocks as defined above. See Section 5.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-

bit addressing support of drives with capacities over 137GB.

3.3 Default logical geometry

Cylinders Read/write heads Sectors per track

16,383 16 63

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed logical blocks as defined above.

3.4 Physical organization

Drive model Read/write heads Number of discs

ST9640322AS ST9640320AS

ST9500320AS ST9400321AS ST9320312AS

ST9320310AS ST9250310AS ST9160316AS 1

4 2

8 Momentus Product Manual, Rev. D

+ 30 hidden pages