Seagate ST90250N1A1ASRK, ST903203N1A2ASRK, ST905003N1A1ASRK, ST9120410AS, ST9120410ASG User Manual

...

Product Manual

Momentus 7200.4 SATA

ST9500420AS ST9320423AS ST9250410AS ST9160412AS ST9120410AS ST980412AS

ST9500420ASG ST9320423ASG ST9250410ASG ST9160412ASG ST9120410ASG ST980412ASG

100534376 Rev. C November 2010

LLC in the United States and/or other countries. Momentus and SeaTools are eith er trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or regis te red tra dem arks a re th e pr operty of their respective owners.

No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC. Call 877-PUB-TEK1(877-782-8351) to request permission.

One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer's operating system may use a different standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage. Seagate reserves the right to change, without notice, product offerings or specifications.

Contents

1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.4 Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.5 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.6 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.7 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.8 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.9 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.9.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.9.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.9.3 Voltage tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.9.4 Power-management modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.10 Environmental specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10.3 Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10.4 Wet bulb temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10.5 Altitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10.6 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10.7 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.11 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.12 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.13 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.13.1 Free Fall Protection feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.14 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.14.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.14.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.14.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.15 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.15.1 European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 17

2.15.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 17

2.16 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.3 Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.0 Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.3.1 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4.3.3 S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Momentus 7200.4 SATA Product Manual, Rev. C i

ii Momentus 7200.4 SATA Product Manual, Rev. C

List of Figures

Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 4. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Momentus 7200.4 SATA Product Manual, Rev. C iii

1.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus

Standard models Free Fall Protection models

ST9500420AS ST9500420ASG ST9320423AS ST9320423ASG ST9250410AS ST9250410ASG ST9160412AS ST9160412ASG ST9120410AS ST9120410ASG ST980412AS ST980412ASG

7200.4 SATA model drives:

These drives provide the following key features:

• 7200-RPM spindle speed.

• 16-Mbyte buffer.

• Free Fall Protection (on ST9500420ASG, ST9320423ASG, ST9250410ASG, ST9160412ASG, ST9120410ASG and ST980412ASG models only)

• Quiet operation. Fluid Dynamic Bearing (FDB) motor.

• High instantaneous (burst) data-transfer rates (up to 3.0 Gbits per second).

• Perpendicular recording technology.

• State -of-the-art cache and on-the-fly error-correction algorithms.

• Native Command Queuing (NCQ) with command ordering.

• Full-track multiple-sector transfer capability without local processor intervention.

• 1000 Gs nonoperating shock and 350 Gs of operating shock.

• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• The 3D Defense System™, which includes Drive Defense, Data Defe nse and Diagnostic Defense, of fers the industry’s most comprehensive protection for disc drives.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

Momentus 7200.4 SATA Product Manual, Rev. C 1

1.1 About the Serial ATA interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:

• Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set any jumpers or other configuration options .

• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.

• Scalability to higher performance levels.

In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current system and expect all of your existing applications to work as normal.

The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0 (master) devices.

Note. The host adapter may, optionally, emulate a master/slave environment to host software where two

devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA environment.

The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated.

The Serial ATA host adapter contains a set of registers that shadow the content s of the traditio nal device regi sters, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. The specification can be downloaded from http://www.serialata.org.

2 Momentus 7200.4 SATA Product Manual, Rev. C

2.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power.

2.1 Specification summary table

The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.

Table 1: Drive specific ations

Drive specification

Formatted GB (512 bytes/sector)* 500 320 250 160 120 80 Guaranteed sectors 976,773,168 625,142,448 488,397,168 312,581,808 234,441,648 156,301,488 Bytes per sector 512 Physical read/write heads 4 3/4 2 2 1/2 1 Discs 221111 Cache (Mbytes) 16 Recording density in BPI (max) 1490k Track density TPI (max) 265k

Areal density (Gb/in Spindle speed (RPM) 7200 Average latency (msec) 4.17 Internal transfer rate (Gb/s max) 1.23 I/O data transfer rate (Gb/s max) 3.0 ATA data-transfer modes supported SATA 1.0, Serial ATA Revision 2.6

Height (max) 9.5 +/- 0.2 mm (0.370 +/- .008 in) Width (max) 69.85 +/- 0.25 mm (2.750 +/- 0.010 in) Length (max) 100.35 +0.20 / -0.25 mm (3.951 +0 .008 / -0.010 in) Weight (max) 110 grams (0.238 lb) 105 grams (0.227 lb) Power-on to ready (sec typical) 4.5 Standby to ready (sec typical) 3.0 Track-to-track seek time, read

(ms typical) Average seek, read (ms typical) 11.0 Average seek, write (ms typical) 13.0 Startup current, +5V (max) 1.0 amps Seek power (typical) 2.2 watts

max) 394

ST9500420AS ST9500420ASG

PIO modes 0–4 Multiword DMA modes 0–2 Ultra DMA modes 0–6

1.5

ST9320423AS ST9320423ASG

ST9250410AS ST9250410ASG

ST9160412AS ST9160412ASG

ST9120410AS ST9120410ASG

ST980412AS ST980412ASG

Momentus 7200.4 SATA Product Manual, Rev. C 3

Table 1: Drive specifications

Drive specification

ST9500420AS ST9500420ASG

ST9320423AS ST9320423ASG

ST9250410AS ST9250410ASG

Read power (typical) 2.1 watts Write power (typical) 2.2 watts Idle mode, low power (typical) 0.69 watts Standby mode 0.20 watts (typical)*** Sleep mode 0.20 watts (typical)*** Voltage tolerance (including noise) +5V ± 5% Ambient temperature 0°C to 60°C (operating)

–40°C to 70°C (nonoperating)

Temperature gradient

20°C (operating), 35°C (nonoperating)

(°C per hour max) Relative humidity 5% to 95% (operating and nonoperating Relative humidity gradient 30% per hour max Wet bulb temperature (°C max) 37.7 (operating)

40 (nonoperating) Altitude, operating –304.8 m to 3048 m (–1000 ft to 10,000 Altitude, nonoperating

–304.8 m to 12,192 m (–1000 ft to 40,000

+ ft)

(meters below mean sea level, max) Shock, operating (Gs max at 2 msec) 350 Shock, nonoperating

800 (Gs max at 2 msec)

Shock, nonoperating

1,000 (Gs max at 1 msec)

Shock, nonoperating

600 (Gs max at 0.5 msec)

Vibration, operating 1.0 G (0 to peak, 5–500 Hz) Vibration, nonoperating 5 Gs (0 to peak, 5–500 Hz) Drive acoustics, sound power (bels) Idle** 2.3 (typical)

2.5 (max)

Performance seek 2.6 (typical)

2.7 (max)

Nonrecoverable read errors 1 per 10

bits read Annualized Failure Rate (AFR) 0.5% Load/Unload (U/UL) cycles

25°C, 50% relative humidity

32°C, 80% relative humidity 5°C, 80% relative humidity

600,000 software-controlled power on/off cycles 50,000 hard power on/off cycles

600,000 software-controlled power on/off cycles

50,000 hard power on/off cycles 5°C, 10% relative humidity 55°C, 16% relative humidity

Warranty For information regarding Warranty Support, visit

Supports Hotplug operation per

http://www.sea

Yes (requires COMRESET from host after a hotplug event)

gate.com/www/en-us/support/warranty_&_returns_assistance

Serial ATA Revision 2.6 specification

ST9160412AS ST9160412ASG

ST9120410AS ST9120410ASG

ST980412AS ST980412ASG

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby

modes will not contribute to battery power consumption.

4 Momentus 7200.4 SATA Product Manual, Rev. C

2.2 Formatted capacity

Model Formatted capacity* Guaranteed sectors Bytes per sector

ST9500420AS and ST9500420ASG 500 Gbytes 976,773,168 512 ST9320423AS and ST9320423ASG 320 Gbytes 625,142,448 512 ST9250410AS and ST9250410ASG 250 Gbytes 488,397,168 512 ST9160412AS and ST9160412ASG 160 Gbytes 312,581,808 512 ST9120410AS and ST9120410ASG 120 Gbytes 234,441,648 512 ST980412AS and ST980412ASG 80 Gbytes 156,301,488 512

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

2.2.1 LBA mode

When addressing these drives in LBA mode, all blocks (

sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above. See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-

bit addressing support of drives with capacities over 137 Gbytes.

2.3 Default logical geometry

Cylinders Read/write heads Sectors per track

16,383 16 63

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above.

2.4 Physical organization

Drive model Read/write heads Number of discs

ST9500420AS and ST9500420ASG 4 2 ST9320423AS and ST9320423ASG 3/4 2 ST9250410AS and ST9250410ASG 2 1 ST9160412AS and ST9160412ASG 2 1 ST9120410AS and ST9120410ASG 1/2 1 ST980412AS and ST980412ASG 1 1

Momentus 7200.4 SATA Product Manual, Rev. C 5

2.5 Recording and interface technology

Interface Serial ATA (SATA) Recording method Perpendicular Recording density BPI (bits/inch max) 1490k Track density TPI (tracks/inch max) 265k Areal density (Gbits/inch2 max) 394 Spindle speed (RPM) (± 0.2%) 7200 Maximum Internal transfer rate (Gbits/sec) 1.23 I/O data-transfer rate (Gbits/sec max) 3.0 Interleave 1:1 Cache buffer 16 Mbytes (16,384 kbytes)

2.6 Physical characteristics

Drive specification

Height (mm)

(inches)

Width (mm)

(inches)

Length (mm)

(inches)

Typical weight

ST9500420AS ST9500420ASG ST9320423AS ST9320423ASG

ST9250410AS ST9250410ASG ST9160412AS ST9160412ASG ST9120410AS ST9120410ASG ST980412AS ST980412ASG

9.5 +/-0.2

0.370 +/-0.008

69.85 +/-0.25

2.750 +/-0.010

100.35 +0.20 / -0.25

3.951 +0.008 / -.010

110 grams

0.238 pounds

105 grams

0.227 pounds

6 Momentus 7200.4 SATA Product Manual, Rev. C

2.7 Seek time

Seek measurements are taken with nominal power at 25°C am bient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows:

• Track-to-track seek time is an average of all

• Average seek time is a true statistical random average random tracks, less overhead.

Table 2: Typical seek times

Typical seek times (msec) Read

Track-to-track 1.5 Average 11.0 Full-stroke 22.0 Average latency 4.17

Note. These drives are designed to consistently meet the seek times represented in this manual. Physical

seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted values. However, due to the manner in which these drives are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications.

possible single-track seeks in both directions.

of at least 5000 measurements of seeks between

2.8 Start/stop times

Time to ready Typical

Power-on to Ready (sec) 4.5 5.0 Standby to Ready (sec) 3.0 3.5

Max @ 25°C

Momentus 7200.4 SATA Product Manual, Rev. C 7

2.9 Power specifications

The drive receives DC power (+5V) through a native SATA power connector.

2.9.1 Power consumption

Power requirements for the drives are listed in the t ab le on

page 8. T ypi cal powe r measur ements are based on

an average of drives tested, under nominal conditions, at 25°C ambient temperature.

• Spinup power

Spinup power is measured from the time of power-on to the

time that the drive spindle reaches operating speed.

• Seek mode

During seek mode, the read/write actuator arm moves towar

d a specific position on the disc surface and does not execute a read or write operation. Servo electronics a re active . Seek m ode p ower is measur ed based on three random seek operations every 100 msecs. This mode is not typical.

• Read/write Read/write power is measured with the heads on track, ba

power and current

sed on three 63 sector read or write operations

every 100 msecs.

• Idle mode power

Idle mode power is measured with the drive up to speed, with

servo electronics active and with the heads in

a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but th

e drive is not spinning, and the ser vo and read/

write electronics are in power-down model

Table 3: DC power

Power dissipation +5V input average (25° C)

Spinup (max) 1.0 amps Seek 2.2 watts Read 2.1 watts Write 2.2 watts Idle, performance* 1.4 watts Idle, active* 1.0 watts Idle, low power mode* 0.69 watts Standby 0.20 watts Sleep 0.20 watts

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

8 Momentus 7200.4 SATA Product Manual, Rev. C

+ 30 hidden pages