Seagate ST336704FC-FCV, ST318304FC-FCV User Manual

Cheetah 36LP FC Installation Guide

Models ST336704FC/FCV and ST318304FC/FCV
Fibre Channel interface disc drive

Publi cation Number: 83329481, Rev. B, November 2000

Handling precautions/Electrostatic discharge protection

• Disc drive s are fragi le. Do not dr op or jar the drive and handle the drive
only by the edg es or frame.

• Drive electronics are extremely sensitive to static electricity. Keep the
drive in its antistatic container until you ar e ready t o install it. Wear a wrist
strap and cable connected to ground. Discharge static from all items near
or that will contact the drive. Never use an ohmmeter on any circuit
boards.

• Turn off the power to the host system during instal lation.

• Always use forced-air ventilation when operating the drive.

• Use caution when troubleshooting a unit that has voltages present.

• Do not disassemble the drive; doing so voids the warranty.

• Return the entire drive for depot service if any part is def ective.

• Do not apply pressure or attach labels to circuit board or drive top.

Electromagnetic compliance

See Safety and Regulatory Agency Specifications, p/n 75789512.

Driv e char ac teris tics

ST336704 ST318304

Formatted capacity 36.7 Gbytes 18.35 Gbytes
Max. data blocks 71,687,369 35,964,301

Cylinders and heads (user accessible) 14,100/12 heads 14,100/6 heads
Disc rotation 10,033 rpm 10,033 rpm

Operating v oltages +5V +12V +5V +12V
Typical operating cu rrent 0.93A 1.14A 0.93A 0.91A

What you need

• Phillips screwdriver and four 6-32 UNC drive mounting screws

• F orced-air ventilation to provide adequate drive cooling

• Host system with Fibre Channel host adapter or backplane

Installation instructions

1. Mount the drive in the host system carrier or tray

Most Fibre Channel host systems (including enclosures) provide a way to
insert the drive using a carrier or tray which allows the drive to be hot­plugge d into the sys tem’s Fibre Cha nnel 40-pin single connector attach­ment (FC-SCA).

Mount th e drive to the carrier or tr ay prov ided by th e ho st system usi ng four
6-32 UNC screws. Two mounting holes are in each side of the drive and
there are four mounting holes in the bottom of the drive. Do not over-tighten
or force the screws. You can mount the drive in any orientation. See Figure
Figure 1.

FC and FCV d rives are desi gned to be att ache d t o the h ost s yst em

Note.

without I/O or power cables.

(0445DCC8h) (0224C58Ch)

Figure 1 above shows a generic carrier. Most carriers will look dif fer-

Note.

ent than the o ne shown. Many are actu ally sm all enc losur es rath er
than brackets as shown here.

2. Insert the drive

Slide th e ca rrier or tray in to th e approp riat e bay in yo ur ho st sys tem. T his
connects the drive directly to your system’s 40-pin Fibre Channel single
connector attachment (FC-SCA). The FC-SCA connector is normally
located on a Fibre Channel back panel.

There ar e no ju mpers o r t er m inators o n t h e d rive, and p ower is s up -

Note.

plied through the 40-pin connector.

3. Connect LEDs (optional)

This is an opti onal step. T he dri ve will wor k fine without the LEDs

Note.

connected to the drive.

The drive supplies pins that you can use to connect fault and active LEDs.
This allows you to monitor drive fault conditions and activity. The actual
LED is external to the drive.

Drive
Front

J6

Reserved

Port A Bypass LED [1]
Port B Bypass LED [1]
Fault LED [1]
Reserved
Active LED [2]
+5V
Active LED [1]
Ground [3]

Pin 1

[1] The drive ha s a 2.2K oh m re si st or in series with this LED driver. Tie the

minus side of an external high-efficiency LED (i.e., 2ma) to this pin.
Connect the plu s side of the LED to +5 V.

[2] An external current-limiting resistor is required when connecting an

LED to th is pin. Th e m inu s s ide of th e resist or /LED combinat io n is c on ­nected to this pin. Connect the plus side to +5V.

[3] Jumper stora ge location (across pins 2 an d 4).

Figure 2. LED indicator connector

Fault LED Signal

The drive activates the fault LED Out signal when:

• the drive det ects failure of both ports

• the drive det ects an internal failure

• the drive receives the appropriate fault LE D command from the host

Active LED signal

The drive activates the active LED signal as indicated below.

Normal command activity LED status

Spun down and no activity ............. Slow blink (20% on and 80% off)

Spun down and activity .................. On

(comm an d execu tin g)

Spun up and no activity.................. On

Spun up and activity ....................... Off

(comm an d execu tin g)

Spinning up or down....................... Blinks steadily (50% on and 50% off)

Format in progre ss ........ .... ............. Toggles on/off

(each cy li nder chan ge )

Figure 1. Sample drive carrier

4. Format the drive

The drive has been low level formatte d at the factor y. You do not n eed to
perform another low level format on this drive unless you decide to perform
cert ai n diag nos tics thr ough the hos t adap te r. If you do dec ide to pe rfor m a
low level format, d o not abo rt the format as thi s is likely to make the dr ive
inoperable. A low level format, with veri fy turn ed on, will typ ically ta ke two
hours.

Protect against power failure or other power interruptions during the format.
a. Turn on DC power to the host system.
b. Boot the system from a system floppy, CD, or from a previously

insta lled hard disc drive if there is one.

c. Format the dri ve.

Caution.

Formatt ing a dr ive eras es all us er data. B e sure tha t you un der­stand this principle before formatting any hard disc drive. It is not
necessary to format a drive that previously has been used to
store data, unless your intention is to erase all user data. S eagate

is not responsible for lost user data.
Cheetah disc dr ives are design ed to oper ate with a variety of operating sys­tems. Please refer to your system or Fibre Channel host adapter (controller)
manual for information about formatting and setting up the drive for use with

your particul ar op er a tin g sy s t em .

Hot plugging the drive

This drive features hot plugging capabilities which allows you to insert and
remove the drive without powering down the host system. Any time a drive
is inser te d or removed from a F ibre Chan nel lo op, a sho r t loop inter ru ption
occurs and the loop resynchronizes automatically to accommodate the
added (or rem oved ) dri ve.

Drive startup options

The drive’s motor will sta rt spin ni ng the dis cs ba se d on the st atus of t wo si g­nals set by the host adapter. These two signals are called Start_1 and
Start_2 . There are four options as describ ed below.

Option Start_2 Start_1 Motor spin function

1........... Low .......Low ........ Motor spins up at DC power on.

2 . .......... High ...... Low . ....... Motor spi ns up when the host adapter sen ds

the SCSI Start command.

3 ........... Low ....... High........ Motor spins up after a delay of 12 seconds

times the physical address of the drive.

4........... High ...... High........The drive will not spin up.

Most systems that host only a couple of drives use option 1 to enable all of
the drives to st art up im mediat el y w h en pow er i s applied to the d r i ves. Sy s ­tems h osti ng la rge r nu mbe rs of dr ives may be con fig ured to start d rives at
various times to avoid overloading the capabilities of the host system’s
power supply.

If you want to change the startup option for the drive, please refer to the
docum enta tio n prov ided wit h yo ur Fib re C ha nnel host ad apte r or ho st sy s­tem.

Troubleshooting

•

Drive d oes not spi n up.

drive bay on t h e h os t- s u pplied carrier or tr ay. Make sure t h e d r i ve m a kes
firm contact with the host’s FC backpanel connector. Also, check the
drive sta rt up opt ions for t he Star t_1 and S tar t_2 sig nals co ntrol led fr om
your host adapter. See “Drive Startup Options” above for the four possi­ble startup options.

•

Computer does not seem to recognize the drive.

is enabled b y the FC host adapter setup utility.

Remove and then reinsert the drive into the

Verify that th e drive

Seagate support services

For online inf ormation about Seagate products, visit www.seagate.com or e­mail your disc questions to [e-mail]

If you nee d he lp insta lling yo ur dri ve, con sult your deal er firs t. If you need
additio nal help, ca ll a Seagat e technica l suppor t specia list. Befo re calling ,
note your system configuration and drive model number (ST336704 or

ST318304).

Africa [phone] Norway 800-113 91
Australia 1800-14-7201 Poland 00 800-311 12 38
Austria 0 800-20 12 90 Spain 900-9 8 31 24
Belgium 0 800-74 876 Sweden 0 207 90 073
Denmark 80 88 12 6 6 Switzerland 0 800-83 84 11
France 0 800-90 90 52 Singapore 800-1101-150
Germany 0 800-182 6831 Taiwan [phone]
Hong Kong 800-90-0474 Thailand 001-800-11-0032165
Indone si a 001-80 3- 1 -003-21 65 Turkey 0 0 800-31 92 91 40
Ireland 1 800-55 21 22 United Kingdom 0 800-783 5177
Italy 800-790695 USA/Canada/ 1-800 SEAGATE or
Malaysia 1-800-80-2335 Latin America [phone]
Middle East [phone] Other European
Netherlands 0 800-732-4283 countries [phone]
New Zealand 0800-443988

Warranty.
Return Merchandise Authorization (RMA).

is defective. Seagate Worldwide customer service centers are the only facilities autho­rized to service Seagate drives. Contact nearest center for return procedures and trade
regulations.

Shipping the drive
Caution.

data lost during s hipping or serv ice. Shipping dr ive in an una pproved container voids
the warranty. Pack the drive with or iginal box and packing materials. Use no o ther
materials. This prevents electrical and physical damage in transit.

Contact your place of purchase or our web site (above).

Before returning t he d r ive, verify th at i t

Back up the data before shipping. Seagate assumes no respons ibility for

© 2000 Seagate Technology LLC. All rights reserved
Publication number: 83329481, Rev. B, November 2000, Printed in U.S.A.
Seagate, Seagate Technology, the Seagate Logo, and Che etah are either regist ered

trademarks or tr ademarks of S eagate Technology LLC. All other trade marks are th e
property of their respective owners.