Seagate ST1000LX015 User Manual
™
5400 RPM - SATA Product Manual
Standard models
ST2000LX001
ST1000LX015
ST500LX025
100802299, Rev. F
October 2017
Document Revision History
Revision Date Pages affected and Description of change
Rev. A 07/05/2016 Initial release.
Rev. B 08/18/2016
5, 13, 18 & 20: Re-Branded to FireCuda.
16: Added warning statement for Class B devices in Korean
Rev. C 08/31/2016 5-6: Added NAND flash text
fc: Added FireCuda logo to cover page
5: Add MTC bullet & change Perpendicular recording to SMR
Rev. D 11/14/2016
9: Revise Section 2.7.1 Power consumption & Table 4 DC Power Requirements
12: Revise Section 2.7.4 Power management modes
16: Updated Korean text for MSIP statement
fc: New horizontal FireCuda logo
7: Added Power-off/Flush Command note after Table 1
Rev. E 02/22/2017
7 & 16: Revised Rated Workload statements
16: Added Section 2.11.1 Data loss under power interruption with write cache enabled
19-20: Updated 2-disk mechanical drawing & added 1-disk drawing
17-20: Updated Sections 2.12 through 2.14.3
Rev. F 10-06-2017
21: Removed (drives support latching SATA connectors)
22-24: Updated Figures 4-6 (mechanical drawings)
a
© 2017 Seagate Technology LLC. All rights reserved.
Publication number: 100802299, Rev. F October 2017
Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. SeaTools and 3D Defense System are
either a trademark or registered trademark of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certification mark
of NIST, which does not imply product endorsement by NIST, the U.S., or Canadian governments. All other trademarks or registered trademarks are the property of their respective
owners.
No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC.
Call 877-PUB-TEK1(877-782-8351) to request permission.
When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different
standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage.
Actual quantities will vary based on various factors, including file size, file format, features and application software. Actual data rates may vary depending on operating environment
and other factors. The export or re-export of hardware or software containing encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for
more information, visit www.bis.doc.gov), and controlled for import and use outside of the U.S. Seagate reserves the right to change, without notice, product offerings or specifications.
Contents
Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1.1 About the Serial ATA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.0 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.1 Formatted Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Recording and Interface Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5 Seek time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.6 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.7 Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.7.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.7.2 Conducted noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.7.3 Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.7.4 Power management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.8 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8.1 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8.2 Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.9 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.9.1 Test for prominent discrete tones (PDTs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.10 Electromagnetic Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.10.1 DC Magnetic Field Immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.11 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.11.1 Data loss under power interruption with write cache enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.12 Agency and Safety Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.13 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.13.1 European Union (EU) CE Marking Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.13.2 Australian RCM Compliance Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.13.3 Canada ICES-003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.13.4 South Korean KC Certification Mark. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.13.5 Morocco Commodity Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.13.6 Taiwanese BSMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.13.7 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
2.14 Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.14.1 European Union Restriction of Hazardous Substance Law . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.14.2 China Requirements —China RoHS 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.14.3 Taiwan Requirements — Taiwan RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.15 Corrosive Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Seagate FireCuda Product Manual, Rev. F 2
Contents
3.0 Configuring and Mounting the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1 Handling and Static-Discharge Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2 Configuring the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.1 Serial ATA Cables and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3 Drive Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.0 Serial ATA (SATA) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.1 Hot-Plug Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.2 Serial ATA Device Plug Connector Pin Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3 Supported ATA Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3.1 Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.3.2 Set Features command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.3.3 S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Seagate FireCuda Product Manual, Rev. F 3
Figures
Figure 1 Typical 1D - 5V Startup and Operation Current Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 2 Typical 2D - 5V Startup and Operation Current Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 3 Attaching SATA Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 4 Mounting Dimensions (for 1-disk models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 5 Mounting Dimensions (for 1-disk models) (alternate basedeck). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 6 Mounting Dimensions (for 2-disk models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Seagate FireCuda Product Manual, Rev. F 4
Seagate® Technology Support Services
For information regarding online support and services, visit: http://www.seagate.com/contacts/
For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/
For information regarding data recovery services, visit: http://www.seagate.com/services-software/recover/
For Seagate OEM, Distribution partner and reseller portals, visit: http://www.seagate.com/partners/
Seagate FireCuda Product Manual, Rev. F 5
1.0 Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate® FireCuda™ model drives:
Standard models
ST2000LX001
ST1000LX015
ST500LX025
These drives provide the following key features:
• 1000 Gs non-operating shock and 400 Gs of operating shock.
• 128MB buffer.
• 5400-RPM spindle speed.
• Flash-accelerated drives combining 8GB NAND technology with massive HDD storage capacity up to 2TB.
• Full-track multiple-sector transfer capability without local processor intervention.
• High instantaneous (burst) data-transfer rates (up to 6Gb/s).
• MTC TechnologyTM, proprietary data flow management.
• Native Command Queuing (NCQ) with command ordering.
• Quiet operation. Fluid Dynamic Bearing (FDB) motor.
• SeaToolsTM diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• Shingled magnetic recording with perpendicular magnetic recording heads/media.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Support for Read Multiple and Write Multiple commands.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Worldwide Name (WWN) capability uniquely identifies the drive.
1.1 About the Serial ATA Interface
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.
In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow users to
install a Serial ATA host adapter and Serial ATA disk drive in the current system and expect all of the existing applications to work as normal.
The Serial ATA interface connects each disk drive in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave
relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host adapter, the host operating
system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0
(master) devices.
The host adapter may, optionally, emulate a master/slave environment to host software where two devices on separate Serial ATA ports
Note
The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing
host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated.
The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow
Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to
the Serial ATA International Organization: Serial ATA (Revision 2.6). The specification can be downloaded from www.serialata.or
are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host
adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA environment.
g.
Seagate FireCuda Product Manual, Rev. F 6
2.0 Drive Specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the
drive and this drive are used throughout this manual to indicate the following drive models:
The specification summaries listed in the following tables are for quick reference. For details on specification measurement or definition, refer to the
appropriate section of this manual.
Table 1 Drive Specifications Summary
Drive Specification ST2000LX001 ST1000LX015 ST500LX025
Formatted capacity
Guaranteed sectors 3,907,029,168 1,953,525,168 976,773,168
Heads 4 2
Disks 2 1
NAND flash Commercial Multilevel Cell (cMLC) 8GB
Bytes per sector 512 (logical) / 4096 (physical)
Recording density 2296 KFC/in
Track density 580 KTP/in avg
Areal density 1327 Mb/in
Spindle speed 5400 RPM
Data transfer rate (up to) 140 MB/s
Interface SATA 6Gb/s
ATA data-transfer modes supported
Cache buffer 128 MB
Height (mm/in) 7.0 (± 0.2) / 0.276 (± 008)
(1)
2TB 1TB 500GB
2
avg
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–6
Width (mm/in) 69.85 (± 0.25) / 2.750 (± 0.010)
Length (mm/in) 100.35 (+0.20/-0.25) / 3.951 (+0.008/-0.010)
Weight (g/lb) max 96 / 0.212 92 / 0.203
Average latency 5.6 ms
Startup current, Max (+5V ) 1.0 A
Voltage tolerance (including noise) 5V ± 5%
Operating temperature 0° to 60°C
Non-operating temperature (ambient) –40° to 70°C
Temperature gradient
Relative humidity
Relative humidity gradient (max) 30% per hour
Wet bulb temperature
Altitude, operating –304.8 m to 3048 m (–1000 ft to 10,000+ ft)
Altitude, non-operating
(below mean sea level, max)
20°C per hour max (operating)
35°C per hour max (non-operating)
5% to 95% (operating)
5% to 95% (non-operating)
37.7°C max (operating)
40.0°C max (non-operating)
–304.8 m to 12,192 m (–1000 ft to 40,000+ ft)
Seagate FireCuda Product Manual, Rev. F 7
Drive Specifications
Table 1 Drive Specifications Summary (continued)
Drive Specification ST2000LX001 ST1000LX015 ST500LX025
Operational Shock 400 Gs at 2 ms max
Non-Operational Shock 1000 Gs at 1 ms max
Vibration, operating
Vibration, non-operating 5–500 Hz: 5.0 Gs
Nonrecoverable read errors 1 per 10
Average annualized workload rating: <55 TB/year.
Rated workload
Warranty
Load-unload cycles 600,000 at 25°C, 50% rel. humidity
Supports Hotplug operation per the
Serial ATA Revision 3.2 specification
1. One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and
formatting.
Note
If the drive is powered-off before issuing flush cache command, in some instances,
the end user data in the DRAM cache might not be committed to the disk.
The specifications for the product assumes the I/O workload does not exceed the average
annualized workload rate limit of 55 TB/year. Workloads exceeding the annualized rate may
degrade and impact reliability as experienced by the particular application. The average annualized workload rate limit is in units of TB per calendar year.
To determine the warranty for a specific drive, use a web browser to access the following web
page: http://www.sea
From this page, click on the “Is my Drive under Warranty” link. The following are required to be
provided: the drive serial number, model number (or part number) and country of purchase.
The system will display the warranty information for the drive.
gate.com/support/warranty-and-replacements/.
5–200 Hz: 2.0 Gs
201–500 Hz: 1.0 Gs
14
bits read
Ye s
2.1 Formatted Capacity
Model
Formatted Capacity
ST2000LX001 2000 GB 3,907,029,168
ST500LX025 500 GB 976,773,168
1. One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating
environment and formatting.
2.1.1 LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed
sectors as defined above.
Refer to Configuring and Mounting the Drive on page 21 (words 60-61 and 100-103) for additional information about 48-bit addressing support
of drives with capacities over 137 GB.
(1)
Guaranteed Sectors Bytes per Sector
512 (logical) / 4096 (physical)ST1000LX015 1000 GB 1,953,525,168
Seagate FireCuda Product Manual, Rev. F 8
2.2 Physical organization
Drive model Read/write heads Number of discs
ST2000LX001 4 2
ST1000LX015 2 1
ST500LX025 2 1
2.3 Recording and Interface Technology
Interface SATA 6Gb/s
Recording method Perpendicular
Recording density 2276 Kb/in
Track density 580 ktracks/in avg
Areal density 1320 Gb/in2 avg
Spindle speed 5400 RPM
Drive Specifications
Data transfer rate (up to) 140 MB/s
2.4 Physical Characteristics
Height (mm/in) 7.0 (± 0.2) / 0.276 (± 008)
Width (mm/in) 69.85 (± 0.25) / 2.750 (± 0.010)
Length (mm/in) 100.35 (+0.20/-0.25) / 3.951 (+0.008/-0.010)
Typical weight (g/lb)
(2-Disk models)
Typical weight (g/lb)
(1-Disk models)
Cache buffer 128MB
96 / 0.212
92/ 0.203
2.5 Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications
in the table below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks, less overhead.
Table 2 Typical seek times
Typical seek times (ms) Read
Track -to-t rack 1.5
Average 13.0
Average latency 5.6
These drives are designed to consistently meet the seek times represented in this manual. Physical
Note
seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted values.
However, due to the manner in which these drives are formatted, benchmark tests that include
command overhead or measure logical seeks may produce results that vary from these specifications.
Seagate FireCuda Product Manual, Rev. F 9
Drive Specifications
2.6 Start/stop times
Table 3 Start/stop times
Typical seek times (ms) Typ ica l Max @ 25°C
Power-on to ready (sec) 0.6 0.8
Standby to ready (sec) 2.5 3.0
2.7 Power Specifications
The drive receives DC power (+5V) through a native SATA power connector (refer to Figure 3).
2.7.1 Power consumption
Power requirements for the drives are listed in the table in Tab le 4 . Typical power measurements are based on an average of drives tested, under
nominal conditions, at 25°C ambient temperature. These power measurements are done with DIPM enabled.
• Spinup current is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Read/Write current is measured with the heads on track, based on three 64 sector read or write operations every 100 ms.
• The drive supports three idle modes: Performance Idle mode, Active Idle mode and Low Power Idle mode. Refer to Section 2.7.4 for powermanagement modes.
Table 4 DC Power Requirements
Power Dissipation
2-Disk models
+5V input average (25° C)
1-Disk models
+5V input average (25° C)
Spinup (max) 1.00A
Write average 1.80W 1.70W
Read average 1.70W 1.60W
Idle, low power mode 0.50W 0.45W
Standby
(1)
0.13W
Sleep 0.13W
1. Standby power is measured at steady state (after 200ms from transition)
Seagate FireCuda Product Manual, Rev. F 10
Loading...