Momentus 5400.2 Installation Guide
ST9100823A, ST9808211A, ST960822A, ST9408114A and
ST9308110A
ATA Interface Disc Drives
Publication Number: 100310042, Rev. C, October 2004
The easiest way to install your drive
Many of today’s mobile computers have been designed to make it possible for the end user to replace the hard drive. Refer to your system’s user manual for the location of the hard drive compartment and the specific instructions regarding replacement.
Some mobile systems are sealed and require specialized tools to gain access to the hard drive.
Caution. Special training or tools may be needed to service some mobile computers. In some cases, opening the case may void your warranty. Consult your system documentation.
Seagate recommends taking your system to an authorized service technician to replace your hard drive.
Refer to your system manufacturer’s support website for the most up-to- date information. Read and follow all instructions regarding the proper steps to be taken when replacing the systems hard drive.
What you need
•A Phillips screwdriver
•Existing drive mounting screws (reuse)
•Existing drive mounting framework, cage or tray (reuse)
•ATA interface adapter (built into notebook and laptop systems)
Handling precautions/electrostatic discharge protection
•Disc drives are fragile. Do not drop or jar the drive. Handle the drive only by the edges or frame. Keep the drive in the electrostatic discharge (ESD) bag until you are ready to install it to minimize handling damage.
•Drive electronics are extremely sensitive to static electricity. While installing the drive, wear a wrist strap and cable connected to ground.
•Turn off the power to the host system during installation.
•Do not disassemble the drive. Doing so voids the warranty. See the warranty information on page 2.
•Do not apply pressure or attach labels to the circuit board or to the top of the drive.
Drive characteristics
|
ST9100823A |
ST9808211A |
ST960822A |
Formatted capacity |
100 Gbytes |
80 Gbytes |
60 Gbytes |
Total number of sectors* |
195,371,568 |
156,301,488 |
117,210,240 |
Cache size |
8 Mbytes |
8 Mbytes |
8 Mbytes |
|
ST9408114A |
ST9308110A |
Formatted capacity |
40 Gbytes |
30 Gbytes |
Total number of sectors* |
78,140,160 |
58,605,120 |
Cache size |
8 Mbytes |
8 Mbytes |
*One sector equals 512 bytes.
Replacing the existing hard drive
Each system has its own unique hard drive compartment. Refer to your system manual to locate the hard drive compartment and for instructions on removing and replacing the hard drive.
Warning. Turn off the computer. If you have a notebook or laptop computer, disconnect the power charger/adapter and remove the battery before you open the case or touch any internal components.
Note. This drive is designed for a host computer that supplies interface signals and +5V power through a single 44-pin connector. Most mobile computers have a fixed connector that attaches directly to the drive.
Setting the jumpers
Refer to the jumper settings in Figure 1 or on your drive label to configure the drive for your system. Jumper settings can also be accessed online from our web site at www.seagate.com.
Master or single drive: Use the options jumper block shown in Figure 1 to configure the drive for operation. This jumper block is the 4-pin header adjacent to pins 1 and 2 of the I/O signal pins.
Note. For mobile system operation, use cable select (default) or master.
Drive is master (or single drive)
Drive is slave
Cable select
Figure 1. Jumper settings
Drive mounting
You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 2 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:
•Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.
•Use only M3 x 0.5 mounting screws.
•Gently tighten the mounting screws (maximum torque: 4.0 in-lb).
•Four (4) threads (0.080 inches) minimum screw engagement recommended.
|
3.945 +/-0.010 |
0.490 +/- .010 |
|
.157 |
(100.2 +/-.25) |
(12.446 +/- .254) |
|
(3.9878) |
|
|
|
.399 |
|
0.673 |
+/- .010 |
(10.135) |
|
||
|
|
(17.09 |
+/- .254) |
|
Breather Hole |
2.750 +/- .010 |
Do not cover |
(69.85 +/- .25) |
or seal. |
Recommended case temp. |
|
3.567 |
|
|
(90.60) |
||
measurement location |
.551 |
||
2X M3 X 0.5-6H |
|||
|
(13.99) |
||
|
Mounting holes |
||
|
|
||
.374 +/- .008 |
|
Both sides |
|
|
.12 min. full thread |
||
(9.5 +/- .2) |
|
|
|
2X .118 (3.00) |
|
|
|
Both sides |
|
|
|
3.567 |
.551 |
(90.60) |
|
|
(13.99) |
|
inches |
|
(mm) |
|
.399 |
|
(10.135) |
|
4X M3 X 0.5-6H Mounting holes
.10 min. full thread
2.430
(61.72)
Detail A |
|
.160 |
|
Detail A |
(4.06) |
|
|
Figure 2. Mounting dimensions—end, top, side, and bottom views
Configuring the BIOS
After completing the drive installation, restart your computer. Your computer may automatically detect your new drive. If your computer does not automatically detect your new drive, follow the steps below.
1.Restart your computer. While the computer restarts, run the system setup program (sometimes called BIOS or CMOS setup). This is usually done by pressing a special key, such as DELETE, ESC, or F1 during the startup process.
2.Within the system setup program, instruct the system to auto detect your new drive.
3.Save the settings and exit the setup program.
When your computer restarts, it should recognize your new drive. If your system still doesn’t recognize your new drive, see the troubleshooting section on this sheet.
System manufacturer’s operating system restore CD
Refer to your mobile system documentation for specific instructions on restoring the operating system on your newly installed hard drive. Many computers require the use of an operating system restore CD, originally shipped with the system, to reload the operating system on the hard drive.
Microsoft operating system installation instructions
For detailed information about installing a Microsoft operating system on your new Seagate drive, refer to the Microsoft Knowledgebase article references below. To locate an article, go to http://support.microsoft.com and enter the article number in any search box on the Microsoft web site. For example, to view the Knowledgebase article for installing Windows XP on your new Seagate drive:
1.Open your browser.
2.Go to http://support.microsoft.com.
3.Enter 313348 in the Microsoft web site search box.
4.Press Enter.
The article is displayed on your screen.
Operating system |
Microsoft Knowledgebase article numbers |
Windows XP |
313348 |
Windows 2000/NT |
308209 (see also: 175761) |
Windows Me/98/95 |
255867 (see also: 166172) |
Preparing the drive using DiscWizard
We recommend using DiscWizard Starter Edition to automatically partition and format your drive. DiscWizard software is available at www.seagate.com and is free. To run DiscWizard:
1.Insert your bootable DiscWizard Starter Edition diskette or CD and follow the instructions. DiscWizard will guide you through the installation process.
2.Boot your computer from the Windows operating system CD-ROM or from your system startup diskette with the Windows CD loaded. Follow the instructions provided on your screen.
Troubleshooting
If your drive is not working properly, these troubleshooting tips may help solve the problem.
1.Does the drive spin up? A spinning drive produces a faint whine and clicking noise. If your drive does not spin, check that the power connector and interface cable are securely attached.
2.Does the computer recognize the drive? Verify that the drive is enabled in the system CMOS or setup program. If not, select the auto detect option and enable it. If your drive has a problem, it may not be recognized by the system. If the operating system does not recognize the drive, you need to load your host adapter drivers.
3.Does FDISK detect the drive? Run the FDISK program located on your Windows startup diskette. Type fdisk/status to verify that your hard drive is present and recognized by the system.
4.I’m running Windows 98 and FDISK is not reporting the full capacity of my drive. Why? You need to upgrade your version of FDISK if you are using the diskettes or CD that came with your original Windows 95 or 98 operating system. Microsoft provides a free downloadable FDISK upgrade. See Microsoft Knowledgebase article number: 263044 located at http://support.microsoft.com.
5.Does ScanDisk find the drive defect-free? ScanDisk is a utility located on your Windows startup diskette that scans the drive for defects. If defects are detected, this may be an indication of a problem.
6.Why does my computer hang on startup? Verify that your system is ATA compatible. You need either an ATA-compatible motherboard connector or ATA host adapter to use this drive.
Note. If these tips do not answer your question or solve the problem, contact your dealer or visit http://seatools.seagate.com to download SeaTools™ disc diagnostics software and more troubleshooting advice.
Seagate support services
For online information about Seagate products, visit www.seagate.com or e-mail your disc questions to DiscSupport@Seagate.com.
If you need help installing your drive, consult your dealer first. If you need additional help, call a Seagate technical support specialist. Before calling, note your system configuration and drive model number.
Africa |
+1-405-324-4714 |
Netherlands |
00 800-47324283 |
Australia |
1800-14-7201 |
New Zealand |
0800-443988 |
Austria |
0 800-20 12 90 |
Norway |
00 800-47324283 |
Belgium |
00 800-47324283 |
Poland |
00 800-311 12 38 |
China* |
800-810-9668 |
Spain |
00 800-47324283 |
Denmark |
00 800-47324283 |
Sweden |
00 800-47324283 |
France |
00 800-47324283 |
Switzerland |
00 800-47324283 |
Germany |
00 800-47324283 |
Singapore |
800-1101-150 |
Hong Kong |
800-90-0474 |
Taiwan* |
00-800-0830-1730 |
Hong Kong† |
001-800-0830-1730 |
Thailand |
001-800-11-0032165 |
India |
1-600-33-1104 |
Turkey |
00 800-31 92 91 40 |
Indonesia |
001-803-1-003-2165 |
United Kingdom |
00 800-47324283 |
Ireland |
00 800-47324283 |
USA/Canada/ |
1-800 SEAGATE or |
Italy |
00 800-47324283 |
Latin America |
+1-405-324-4700 |
Japan |
0034 800 400 554 |
Other European |
|
Malaysia |
1-800-80-2335 |
countries |
+1-405-324-4714 |
Middle East |
+1-405-324-4714 |
|
|
*Mandarin
†Cantonese
Warranty. To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our web site at www.seagate.com for more information.
Return Merchandise Authorization (RMA). Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. Seagate offers comprehensive customer support for all Seagate drives worldwide. Seagate customer service centers are the only facilities authorized to service Seagate drives. Drive return procedures vary depending on geographical location and are subject to current international trade regulations.
Shipping the drive
Caution. Back up the data before shipping. Seagate assumes no responsibility for data lost during shipping or service.
Shipping drive in an unapproved container voids the warranty. Pack the drive with original box and packing materials. Use no other materials. This prevents electrical and physical damage in transit.
Electromagnetic compliance for the European Union. This model complies with the European Union requirements of the Electromagnetic Compatibility Directive 89/ 336/EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993. Compliance of this drive, as a system component, was confirmed with a test system. We cannot guarantee that your system will comply. The drive is not meant for external use (without properly designed enclosure, shielded I/O cable, etc.).
Sicherheitsanleitung 1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umgebungstempeatur von 60°C vorgesehen ist. 2. Zur Befestigung des Lufwerks werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht merh als 3,3 mm und bei Befestigung an der Unterseite nicht mehr als 5,08 mm betragen. 3. Als Versorgungsspannugen werden benötigt: +5V +/- 5% 0,74A; +12V +/- 5% 2,8A 4. Die Versorgungsspannung muss SELV entsprechen. 5. Alle Arbeiten auf dem Festplattte dürfen nur von Ausgebiletem Serciepersonal durchgeführt werden. Bitte entfernen Sie nicht die Aufschriftenschilder des Laufwerkes. 6. Der Einbau des Laufwerkes muss den Anforderungen gemäss DIN IEC 950 VDE 0805/05.90 entspreche.
© 2004 Seagate Technology LLC. All rights reserved
Publication number: 100310042, Rev. C, October 2004, Printed in U.S.A.
Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. Momentus and the Wave logo are registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications.