Seagate BARRACUDA XT SERIES SATA ST32000641AS Product Manual

Product Manual

Barracuda XT Series SATA

ST32000641AS

100586689
Rev. C
January 2010

Revision history

Revision Date Sheets affected or comments

Rev . A 09/15/2009 Initial release.
Rev. B 11/20/2009 Updated drive specifications on Tables 1-3; added “Warranty” specific section. Made

minor text edits throughout.

Rev. C 01/08/2010 Corrected publication part number.

Copyright © 2008-2010 Seagate Technology LLC. All rights reserved. Printed in U.S.A.
Publication number: 100586689, Rev. C January 2010
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United

States and/or other countries. Barracuda, SeaTools and SeaTDD are either trademarks or registered trademarks of Sea
gate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or
registered trademarks are the property of their respective owners.

When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion
bytes. Your computer's operating system may use a different standard of measurement and report a lower capacity. In
addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data stor
age. Seagate reserves the right to change, without notice, product offerings or specifications.

-

-

Contents

1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.4 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.5 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.6 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.6.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.6.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.6.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.6.4 Power management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.7 Environmental specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.7.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.7.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.7.3 Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.7.4 Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.7.5 Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.7.6 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.8 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.8.1 Test for Prominent Discrete Tones (PDTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.9 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.11 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.11.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.11.2 Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.11.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.12 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.12.1 European Union Restriction of Hazardous Substances (RoHS) Directive. . . . . 15

2.12.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . 15

2.13 Corrosive environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.0 Configuring and mounting the drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.3 Serial ATA cables and connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.4 Drive mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.0 Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.3.1 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.3.3 S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Barracuda XT Series SATA Product Manual, Rev. C i

ii Barracuda XT Series SATA Product Manual, Rev. C

List of Figures

Figure 1. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 2. Mounting dimensions (2000GB model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Barracuda XT Series SATA Product Manual, Rev. C iii

iv Barracuda XT Series SATA Product Manual, Rev. C

1.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate
Barracuda

®

XT model drives:

ST32000641AS
These drives provide the following key features:

• The SATA 6Gb/s interface enables the use of the industry’s newest and fastest hard drive controllers while providing
backward compatibility to legacy SATA 1.5Gb/s or 3Gb/s systems.

• 7,200 RPM spindle speed.

• High instantaneous (burst) data-transfer rates (up to 600MB per second).

• Perpendicular recording technology provides the drives with increased areal density.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Native Command Queueing with command ordering to increase performance in demanding applications.

• Full-track multiple-sector transfer capability without local processor intervention.

• Compliant with RoHS requirements in China and Europe.

• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Supports latching SATA cables and connectors.

• Worldwide Name (WWN) capability uniquely identifies the drive.

Barracuda XT Series SATA Product Manual, Rev. C 1

1.1 About the Serial ATA interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advan­tages include:

• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other
configuration options.

• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.

• Scalability to higher performance levels.

In addition, Serial ATA makes the transition from parallel ATA easy by pr oviding legacy so ftware support. Serial ATA was
designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive in your current system and expect all
of your existing applications to work as normal.

The Serial ATA interface connects each disk drive in a point-to-p oint configuratio n with the Serial ATA host adap ter. There
is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on on e
Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate
ports. This essentially means both drives behave as if they are Device 0 (master) devices.

Note. The host adapter may, optionally, emulate a master/slave environment to host software where two devices on

separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave)
accessed at the same set of host bus addr esses. A host adapter that emulates a master/slave environment
manages two sets of shadow registers. This is not a typical Serial ATA environment.

The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward
compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data
transfers, resets, and interrupts are all emulated.

The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers,
referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For a ddi tional in form ation
about how Serial ATA emulates parallel ATA, refer to the “Serial ATA International Organization: Serial ATA Revision 2.6”.
The specification can be downloaded from www.sata-io.org.

2 Barracuda XT Series SATA Product Manual, Rev. C

2.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For con­venience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models:

ST32000641AS
The specification summaries listed in the following tables are for quick refe rence. For details on specification measur e-

ment or definition, see the appropriate section of this manual.

Table 1: Drive specifications summary for 2000GB models

Drive specification ST32000641AS

Formatted capacity (512 bytes/sector)* 2000GB
Guaranteed sectors 3,907,029,168
Heads 8
Disks 4
Bytes per sector 512
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density 1421 kb/in
Track density(avg) 240 ktracks/in
Areal density (avg) 347Gb/in
Spindle speed 7200 RPM
Internal data transfer rate (max) 1300Mb/s
Sustained data transfer rate OD(max) 138MB/s
I/O data-transfer rate (max) 600MB/s
ATA data-transfer modes supported PIO modes: 0 to 4

Multiword DMA modes: 0 to 2

Ultra DMA modes 0 to 6
Cache buffer 64MB
Height (max) 26.1mm / 1.028 in
Width (max) 101.85mm / 4.010 in
Length (max) 146.99mm / 5.787 in
Weight (typical) 700g / 1.543 lb
Average latency 4.16ms
Power-on to ready (typical) 15s
Standby to ready (typical) 15s
Startup current (typical) 12V (peak) 2.8A

2

Barracuda XT Series SATA Product Manual, Rev. C 3

Drive specification ST32000641AS

Voltage tolerance (including noise) 5V + 5%

Operating temperature
(Drive Case temperature)

Nonoperating temperature (Ambient) –40° to 70°C
Temperature gradient (max) 20°C per hour max (operating)

Relative humidity 5% to 95% (operating)

Relative humidity gradient (max) 30% per hour
Wet bulb temperature (max) 37.7°C max (operating)

Altitude, operating –60.96m to 3,048m

Altitude, nonoperating
(below mean sea level, max)

Operational Shock (max) 63 Gs at 2ms
Non-Operational Shock (max) 300 Gs at 2ms
Vibration, operating 5 to 350Hz: 0.50 Gs

Vibration, nonoperating 5 to 350Hz: 5.0 Gs

Drive acoustics, sound power
Idle** 2.7 bels (typical)

Performance 2.9 bels (typical)

Nonrecoverable read errors 1 per 10
Warranty To determine the warranty for a specific drive, use a web browser to access the following web

Load-unload cycles 300,000 at 25°C, 50% rel. humidity
Supports Hotplug operation per the

Serial ATA Revision 2.6 specification

12V + 10%

0° to 60°C

30°C per hour max (nonoperating)

5% to 95% (nonoperating)

40.0°C max (nonoperating)

(–200 ft to 10,000+ ft)

–60.96m to 12,192m

(–200 ft to 40,000+ ft)

350 to 500Hz: 0.25 Gs

350 to 500Hz: 2.0 Gs

2.9 bels (max)

3.3 bels (max)

14

bits read

page:

support.seagate.com/customer/warranty_validation.jsp

From this page, click on the “Verify Your Warranty” link. Y ou will be asked to provide the drive serial
number, model number (or part number) and country of purchase. The system will display the war
ranty information for your drive.

Yes

-

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and

formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to

operational levels.

4 Barracuda XT Series SATA Product Manual, Rev. C

2.1 Formatted capacity

Model

ST32000641AS 2000GB 3,907,029,168 512

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depe nding on operating environment and

formatting.

Formatted
capacity*

Guaranteed
sectors

Bytes per sector

2.1.1 LBA mode

When addressing these drives in LBA

mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is

the number of guaranteed sectors as defined above.
See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional info rmation about 48 -bit address-

ing support of drives with capacities over 137GB.

2.2 Default logical geometry

Cylinders Read/write heads Sectors per track

16,383 16 63

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is
the number of guaranteed sectors as defined above.

2.3 Recording and interface technology

Interface Serial ATA (SATA)
Recording method Perpendicular
Recording density (kbits/inch max) 1421kb/in
Track density (ktracks/inch avg) 240 ktracks/in

2

Areal density (Gbits/inch
Spindle speed (RPM) 7200 + 0.2%
Internal data transfer rate (Mb/s max) 1300Mb/s
Sustained data transfer rate (MB/s max) 138MB/s
I/O data-transfer rate (MB/s max) 600MB/s

avg) 347Gb/in

2

Barracuda XT Series SATA Product Manual, Rev. C 5

2.4 Physical characteristics

ST32000641AS

Maximum height 26.1mm / 1.028 in
Maximum width 101.85mm / 4.010 in
Maximum length 146.99mm / 5.787 in
Typical weight 700g / 1.543 lb
Cache buffer 64 MB (6 4,768kb)

2.5 Start/stop times

Power-on to ready (s) max. 15.0
Standby to ready (s) max. 15.0
Ready to spindle stop (s) max. 20.0

2000GB model

6 Barracuda XT Series SATA Product Manual, Rev. C

2.6 Power specifications

The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 1 on page 17.

2.6.1 Power consumption

Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an aver­a

ge of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature.

• Spinup power

Spinup power is me asured from the time of power-on to th

• Seek mode

During seek mode, the read/write actuator a rm moves towar d a
cute a read or write operation. Servo electronics ar e active. Seek mode powe r represents the worst-case power con­sumption, using only random seeks with read or write latency time. This mode is not typical and is provided for worst­case information.

• Read/write power and current

Read/write power is measured with the head

s on track, based on a 16-sector write followed by a 32-ms delay, then a

16-sector read followed by a 32-ms delay.

• Operating power and current

Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each 10 reads)

nd 20 percent drive idle mode.

a

e time that the drive spindle reaches operating speed.

specific position on the disk surface and does not exe-

• Idle mode power

Idle mode power is measured with the drive up to speed, with

servo electronics active and with the heads in a random

track location.

• Standby mode

During standby mode, the drive accepts commands, but the drive is n

ot spinning, and the servo and read/write elec-

tronics are in power-down mode.

Table 2: DC power requirements

Power dissipation Avg (watts 25° C ) Avg 5V typ amps Avg 12V typ amps

Spinup — — 2. 8 (p ea k)
Idle* † 6.39 0.27 0.42
Operating (average) 9.23 0.31 0.64
Standby 0.57 0.09 0.01
Sleep 0.57 0.09 0.01

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to

operational levels.

†5W IDLE with DIPLM Enabled

Note. Drive supports PHY layer power management. When enabled, a power savings of ~300mw can be achieved in idle,

standby and sleep modes.

Barracuda XT Series SATA Product Manual, Rev. C 7

2.6.1.1 Typical current profiles

Note.

Typical 5V startup and operatio n cu rre nt profile

Note. Typical 12V startup and operation current profile

8 Barracuda XT Series SATA Product Manual, Rev. C

2.6.2 Conducted noise

Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12V
line or an equivalent 15-ohm resistive load on the +5V line.

• Using 12-V power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected
noise at up to 10MHz.

• Using 5-V power , the drive is expe cted to operate with a maximum of 100 mV peak-to-peak square-wave injected noise
at up to 10MHz.

Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.

2.6.3 Voltage tolerance

Voltage tolerance (including noise):
5V +

10%

12V +

10 %

2.6.4 Power management modes

The drive provides programm able power management to provide greater energy efficiency. In most s ystems, you can
control power management through the system setup program. The drive features the following power management
modes:

Power modes Heads Spindle Buffer

Active Tracking Rotating Enabled
Idle Tracking Rotating Enabled
Standby Parked Stopped Enabled
Sleep Parked Stopped Disabled

• Active mode

The drive is in active mode during the read/write and seek operations.

• Idle mode

The buffer remains enabled, and the drive accepts all commands and returns to active mode any time disk access is
necessary.

• Standby mode

The drive enters standby mode when the host sends a standby Immediate command. If the host has set the standby
timer, the drive can also enter standby mode automatically after the drive has been inactive for a specifiable length of
time. The standby timer delay is established using a standby or idle command. In standby mode, the drive buffer is
enabled, the heads are parked and the spindle is at rest. The drive accepts all commands and returns to active mode
any time disk access is necessary.

• Sleep mode

The drive enters sleep mode after receiving a sleep command from the host. In sleep mode, the drive buffer is dis­abled, the heads are parked and the spindle is at rest. The driv e leaves sleep mode after it receives a hard reset or soft
reset from the host. After receiving a reset, the drive exits sleep mode and enters standby mode with all current trans­lation parameters intact.

• Idle and Standby timers

Each time the drive performs an active function (read, write or seek), the standby timer is reinitialized and begins
counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is
required, the drive makes a transition to standby mode. In both Idle and standby mode, the drive accepts all com­mands and returns to active mode when disk access is necessary.

Barracuda XT Series SATA Product Manual, Rev. C 9

2.7 Environmental specifications

2.7.1 Ambient temperature

Ambient temperature is defined as the temperature of the envir

onment immediately surrounding the drive. Actual drive

case temperature should not exceed 69°C (156°F) within the operating ambient conditions.

Operating: 0° to 60°C (32° to 140°F)

operating: * –40° to 70°C (–40° to 158°F)

Non

* See Section for reliability projections.

2.7.2 Temperature gradient

Operating: 20°C per hour (68°F per hour max), without condensation
Nonoperating: 30°C per hour (86°F per hour max)

2.7.3 Humidity

2.7.3.1 Relative humidity

Operating: 5% to 95% noncondensing (30% per hour max)
Nonoperating: 5% to 95% noncondensing (30% per hour max)

2.7.3.2 Wet bulb temperature

Operating: 37.7°C (99.9°F max)
Nonoperating: 40°C (104°F max)

2.7.4 Altitude

Operating: –60.96m to 3,048m (–200 ft to 10,000+ ft)
Nonoperating: –60.96m to 12,192m (–200 ft to 40,000+ ft)

10 Barracuda XT Series SATA Product Manual, Rev. C

2.7.5 Shock

All shock specifications assume th at the drive is mounted securely with the input shoc k applied at the drive mounting
screws. Shock may be applied in the X, Y or Z axis.

2.7.5.1 Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum operating
shock of 63 Gs based on half-sine shock pulses of 2ms during read operations. Shocks should not be repeated more than
two times per second.

2.7.5.2 Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in perfor­mance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2ms duration.

2.7.6 Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration app lied at the drive m ounting
screws. Vibration may be applied in the X, Y or Z axis.

2.7.6.1 Operating vi bra ti on

The maximum vibration levels that the drive may experience while meeting the performance standards specified in this
document are specified below.

5 to 350Hz 0.50 Gs
350 to 500Hz 0.25 Gs

2.7.6.2 Nonoperating vibration

The maximum nonoperating vibration levels that the drive may experience without incu rr ing physica l da mag e or de gr ada ­tion in performance when subsequently put into operation are specified below.

5 to 350Hz 5.0 Gs
350 to 500Hz 2.0 Gs

Barracuda XT Series SATA Product Manual, Rev. C 11

2.8 Acoustics

Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are
consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a
reflecting plane. For all tests, the drive is oriented with the cover facing upward.

Note. F

or seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the

following equation:

(Number of seeks per second = 0.4 / (average latency + average access time)

Table 3: Drive A-weighted Sound Power Levels (SWL, BA)

[1]

Idle

2000GB model

[1] During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic an d power to

operational levels.

2.7 bels (typ)

2.9 bels (max)

Performance Seek

2.9 bels (typ)

3.3 bels (max)

2.8.1 Test for Prominent Discrete Tones (PDTs)

Seagate follows the ECMA-74 standards for measurement and identification

of PDTs. An exception to this process is the
use of the absolute threshold of hearing. Se agate uses th is threshold curve (origi nated in ISO 3 89-7) to d iscern tone audi­bility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D
of the ECMA-74 standards.

2.9 Electromagnetic immunity

When properly installed in a representative host system, the drive operates without errors or degradation in pe rforman ce
when subjected to the radio frequency (RF) environments defined in the following table:

Table 4: Radio frequency environments

T est Description Performance level Reference standard

Electrostatic
discharge

Radiated RF
immunity

Electrical fast
transient

Surge immunity ± 1 kV differential, ± 2 kV common, AC mains B EN61000-4-5: 95
Conducted RF

immunity
Voltage dips,

interrupts

Contact, HCP, VCP: ± 4

80 to 1,000MHz, 3 V/m,
80% AM with 1kHz sine
900MHz, 3 V/m, 50% pulse modulation @ 200Hz

± 1 kV on AC mains, ± 0.5 kV on external I/O B EN61000-4-4: 95

150kHz to 80MHz, 3 Vrms, 80% AM with 1kHz sine A EN61000-4-6: 97

0% open, 5 seconds
0% short, 5 seconds
40%, 0.10 seconds
70%, 0.01 seconds

kV; Air: ± 8 kV B EN61000-4-2: 95

A EN61000-4-3: 96

C
C
C
B

ENV 50204: 95

EN61000-4-11: 94

12 Barracuda XT Series SATA Product Manual, Rev. C

2.10 Warranty

To determine the warranty for a specific drive, use a web browser to access the following web page:
support.seagate.com/customer/warranty_validation.jsp

From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part
number) and country of purchase. The system will display the warranty information for your drive.

2.11 Agency certification

2.11.1 Safety certification

These products are certified to mee t the req uirement s of U L60950-1 , CSA60950- 1 and EN6095 0 and so mar ked as to the
certify agency.

2.11.2 Electromagnetic Compatibility (EMC)

Hard drives that display the CE mark comply with the Eu ropea n Union (EU) requiremen ts specified in th e Electromagnetic
Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the
product standards for Information Technology Equipment (ITE). Emission levels are defined by EN55022, Class B and the
immunity levels are defined by EN55024.

Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives
when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed
for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all
unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE
marking for their products.

Barracuda XT Series SATA Product Manual, Rev. C 13

Korean RRL

If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of
the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework
requirements of the Radio Research Laboratory (RRL) Communications Commission, Republic of Korea.

These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/
EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab.

• Family name: Barracuda

• Certificate number: In process

Australian C-Tick (N176)

If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ CISPR22 and
meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority
(ACA).

2.11.3 FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an
external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the cus­tomer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.

Seagate has tested this device in enclosures as described abo ve to ensure that the total assembly (enclosure, disk drive,
motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part
15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television recep­tion.

Radio and television interference. This equipment generates and uses radio frequency energy and if not installed and
used in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installation. How­ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interfer­ence to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one
or more of the following corrective measures:

• Reorient the receiving antenna.

• Move the device to one side or the other of the radio or TV.

• Move the device farther away from the radio or TV.

• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You

may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve
Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents,
U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.

14 Barracuda XT Series SATA Product Manual, Rev. C

2.12 Environmental protection

“O”

RoHS MCV

“X”

RoHS MCV

Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting
certain chemical substances.

2.12.1 European Union Restriction of Hazardous Substances (RoHS) Directive

The European Union Restriction of Hazardous Substances (Ro
stances, including Lead, Cadmium, Mercury , Hexaval ent Chromium, PBB and PBDE, in electronic product s, ef fective July

2006. This drive is manufactured with components and materials that comply with the RoHS Directive.

2.12.2 China Restriction of Hazardous Substances (RoHS) Directive

This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains
information mandated by China's "Marking Requirements for Control of Pollution Caused by Electronic
Information Products" Standard.

"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower than the
threshold defined by the China RoHS MCV Standard.

HS) Directive, restricts the presence of chemical sub-

中国限制危险物品的指令

表示该部件（于同类物品程度上）所含的危险和有毒物质低于中国

"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over the thresh­old defined by the China RoHS MCV Standard.

表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国

标准所定义的门槛值。

标准所定义的门槛值。

2.13 Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light indus­trial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this
accelerated testing cannot duplicate every potential application environment. Users should use caution exposing any
electronic components to uncontrolled chemical pollut ant s and corrosive chemicals as electronic drive component reliab il­ity can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are
especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damag­ing. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit
board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrica­tion, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life
of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

Barracuda XT Series SATA Product Manual, Rev. C 15

3.0 Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1 Handling and static-discharge precautions

After unpacking, and before inst allation, the drive may be expo sed to potential handl ing and electrostatic discharge (ESD)
hazards. Observe the following standard handling and static-discharge precautions:

Caution:

• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of

a computer that is plugged into a grounded outlet. Wear a grounded wrist strap thro ughout the entire installation procedure.

• Handle the drive by its edges or frame only.

• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

• Always rest the drive on a padded, antistatic surface until you mount it in the computer.

• Do not touch the connector pins or the printed circuit board.

• Do not remove the fa ctory-installed labels from the drive or cover them with additional labels. Removal voids the warranty.

Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and
contamination.

16 Barracuda XT Series SATA Product Manual, Rev. C

3.2 Configuring the drive

Power cable

Signal cable

Signal connector

Power connector

Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no master/slave
relationship because each drive is considered a master in a point-to-point relationship. If two drives are attached on one
Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate
ports. Both drives behave as if they are Device 0 (master) devices.

Serial ATA drives are designed for easy installation. It is usually not necessary to set any jumpers on the drive for proper
operation; however, if you connect the drive and receive a “drive not detected” error, your SATA-equipped motherboard or
host adapter may use a chipset that does not support SATA speed autonegotiation.

3.3 Serial ATA cables and connectors

The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The
cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 5 for connector pin defi­nitions. Either end of the SATA signal cable can be attached to the drive or host.

For direct backplane connection, the drive connectors are inserted dire ctly into the host recept acle. The drive and the ho st
receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.

For installations which require cables, you can connect the drive as illustrated in Figure 1.

Figure 1. Attaching SATA cabling

Each cable is keyed to ensure correct orientation. Barracuda XT drives support latching SATA connectors.

Barracuda XT Series SATA Product Manual, Rev. C 17

3.4 Drive mounting

Recommended
case temperature
measurement location

You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom­mounting holes. See Figure 2 for drive mounting dimensions. Follow these important mounting precautions when mount­ing the drive:

• Allow a minimum clearance of 0.030 inches (0

• Use only 6-32 UNC mounting screws.

• The screws should be inserted no more than 0.150 inch (3.81 mm) into the bottom or side mounting holes.

• Do not overtighten the mounting screws (maximum torque: 6 inch-lb).

.76 mm) around the entire perimeter of the drive for cooling.

Figure 2. Mounting dimensions (2000GB model)

18 Barracuda XT Series SATA Product Manual, Rev. C

4.0 Serial ATA (SATA) interface

These drives use the industry-standard Seri al ATA interface that support s FIS dat a transfers. It supp orts ATA pro grammed
input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6.

For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment”
specification.

4.1 Hot-Plug compatibility

Barracuda XT drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA
Revision 2.6 specification. This specification can be downloaded from www.serialata.org.

Barracuda XT Series SATA Product Manual, Rev. C 19

4.2 Serial ATA device plug connector pin definitions

Table 5 summarizes the signals on the Serial ATA interface and power connectors.

Table 5: Serial ATA connector pin definitions

Segment Pin Function Definition

S1 Ground 2nd mate
S2 A+ Differential signal pair A from Phy
S3 A­S4 Ground 2nd mate
S5 B- Differential signal pair B from Phy
S6 B+

Signal

S7 Ground 2nd mate

Key and spacing separate signal and power segments

P1 V
P2 V
P3 V

33

33

33

3.3V power

3.3V power

3.3V power, pre-charge, 2nd mate
P4 Ground 1st mate
P5 Ground 2nd mate
P6 Ground 2nd mate

Power

P7 V
P8 V
P9 V

5

5

5

5V power, pre-charge, 2nd mate
5V power

5V power
P10 Ground 2nd mate
P11 Ground or LED signal If grounded, drive does not use deferred spin
P12 Ground 1st mate.
P13 V
P14 V
P15 V

12

12

12

12V power, pre-charge, 2nd mate

12V power

12V power

Notes:

1. All pins are in a single row, with a 1.27 mm (0.050”) pitch.

2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the
mating sequences are:

• the ground pins P4 and P12.

• the pre-charge power pins and the other ground pins.

• the signal pins and the rest of the power pins.

3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a
blind-mate backplane configuration.

4. All used voltage pins (Vx) must be terminated.

20 Barracuda XT Series SATA Product Manual, Rev. C

4.3 Supported ATA commands

The following table lists Serial ATA standard commands that the drive supports.
For a detailed description of the ATA commands, refer to the Serial ATA International Organization:
Serial ATA Revision 2.6 (http://www.sata-io.org).

See “S.M.A.R.T. commands” on page 28 for details and subcommands used in the S.M.A.R.T. implementation.

Table 6: Supported ATA commands

Command name Command code (in hex)

Check Power Mode E5
Device Configuration Freeze Lock B1H / C1
Device Configuration Identify B1H / C2
Device Configuration Restore B1H / C0
Device Configuration Set B1H / C3
Device Reset 08
Download Microcode 92
Execute Device Diagnostics 90
Flush Cache E7
Flush Cache Extended EA
Format Track 50
Identify Device EC
Idle E3
Idle Immediate E1
Initialize Device Parameters 91
Read Buffer E4
Read DMA C8
Read DMA Extended 25
Read DMA Without Retries C9
Read Log Ext 2F
Read Multiple C4
Read Multiple Extended 29
Read Native Max Address F8
Read Native Max Address Extended 27
Read Sectors 20
Read Sectors Extended 24
Read Sectors Without Retries 21
Read Verify Sectors 40
Read Verify Sectors Extended 42
Read Verify Sectors Without Retries 41
Recalibrate 10
Security Disable Password F6

H

H
H
H

H
H
H
H

H

H

H

H
H
H

H

H
H

H

H

H

H

H
H
H
H
H
H
H
H
H
H
H

Barracuda XT Series SATA Product Manual, Rev. C 21

Command name Command code (in hex)

Security Erase Prepare F3
Security Erase Unit F4
Security Freeze F5
Security Set Password F1
Security Unlock F2
Seek 70
Set Features EF
Set Max Address F9

Note: Individual Set Max Address
commands are identified by the value
placed in the Set Max Features regis­ter as defined to the right.

H
H
H
H
H
H

H

H

Address:

Password:

Lock:

Unlock:

Freeze Lock:
Set Max Address Extended 37
Set Multiple Mode C6
Sleep E6
S.M.A.R.T. Disable Operations B0H / D9
S.M.A.R.T. Enable/Disable Auto save B0H / D2
S.M.A.R.T. Enable Operations B0H / D8
S.M.A.R.T. Execute Offline B0H / D4
S.M.A.R.T. Read Attribute Thresholds B0H / D1
S.M.A.R.T. Read Data B0H / D0
S.M.A.R.T. Read Log Sector B0H / D5
S.M.A.R.T. Return Status B0H / DA
S.M.A.R.T. Save Attribute Values B0H / D3
S.M.A.R.T. Write Log Sector B0H / D6
Standby E2
Standby Immediate E0
Write Buffer E8
Write DMA CA
Write DMA Extended 35
Write DMA FUA Extended 3D
Write DMA Without Retries CB
Write Log Extended 3F
Write Multiple C5
Write Multiple Extended 39
Write Multiple FUA Extended CE
Write Sectors 30
Write Sectors Without Retries 31
Write Sectors Extended 34
Write Uncorrectable 45

H

H
H

H
H
H
H
H
H
H
H
H

H
H
H
H

H

H

H

H

H

H

H

H
H
H
H
H

00
01
02
03
04

H
H
H
H
H

22 Barracuda XT Series SATA Product Manual, Rev. C

4.3.1 Identify Device command

The Identify Device command (command code ECH) transfers information about the drive to the host following power up.
The data is organized as a single 512-byte block of data, whose contents are shown in Table 6 on page 21. All reserved
bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See
Section 2.0 on page 3 for default para meter settings.

The following commands contain drive-specific features that may not be included in the Serial ATA specification.

Word Description Value

Configuration information:

0

1 Number of logical cylinders 16,383

• Bit 15: 0 = ATA; 1 = ATAPI

• Bit 7: removable media

• Bit 6: removable controller

• Bit 0: reserved

0C5A

H

2 ATA-reserved 0000
3 Number of logical heads 16
4 Retired 0000
5 Retired 0000
6 Number of logical sectors per logical track: 63 003F
7–9 Retired 0000
10–19 Serial number: (20 ASCII characters, 0000H = none) ASCII
20 Retired 0000
21 Retired 0400
22 Obsolete 0000

23–26

27–46

47

Firmware revision
(8 ASCII character string, padded with blanks to end of string)

Drive model number:
(40 ASCII characters, padded with blanks to end of string)

(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write
multiple (16)

x.xx

8010

48 Reserved 0000
49 Standard Standby timer, IORDY supported and may be disabled 2F00
50 ATA-reserved 0000
51 PIO data-transfer cycle timing mode 0200
52 Retired 0200
53 Words 54–58, 64–70 and 88 are valid 0007
54 Number of current logical cylinders xxxx
55 Number of current logical heads xxxx
56 Number of current logical sectors per logical track xxxx
57–58 Current capacity in sectors xxxx

59

Number of sectors transferred during a Read Multiple
or Write Multiple command

xxxx

H

H
H
H
H

H
H
H

H

H
H
H
H
H

H
H
H
H
H

H

Barracuda XT Series SATA Product Manual, Rev. C 23

Word Description Value

Total number of user-addressable LBA sectors available
(see Section 2.1 for related information)

60–61

*Note: The maximum value allowed in this field is: 0FFFFFFFh
(268,435,455 sectors, 137Gb). Drives with capacities over 137Gb will

0FFFFFFFh*

have 0FFFFFFFh in this field and the actual number of user-address­able LBAs specified in words 100-103. This is required for drives that
support the 48-bit addressing feature.

62 Retired 0000
63

Multiword DMA active and modes supported
(see note following this table)

xx07

64 Advanced PIO modes supported (modes 3 and 4 supported) 0003
65 Minimum multiword DMA transfer cycle time per word (120 nsec) 0078

66

Recommended multiword DMA transfer cycle time per word
(120 nsec)

0078

67 Minimum PIO cycle time without IORDY flow control (240 nsec) 00F0
68 Minimum PIO cycle time with IORDY flow control (120 nsec) 0078
69–74 ATA-reserved 0000
75 Queue depth 001F
76 Serial ATA capabilities xxxx
77 Reserved for future Serial ATA definition xxxx
78 Serial ATA features supported xxxx
79 Serial ATA features enabled xxxx
80 Major version number 003E
81 Minor version number 0028
82 Command sets supported 364B
83 Command sets supported 7C03

4003
(4003H = 0100000000000011
binary)

84

Command sets support extension
(see note following this table)

H

H

H

H

H

H

H

H

H
H
H
H
H

H

H

H
H

See Word 108-111 note.

H

85 Command sets enabled 30xx
86 Command sets enabled 0001
87 Command sets enable extension 4000
88 Ultra DMA support and current mode (see note following this table) xx3F
89 Security erase time 0000
90 Enhanced security erase time 0000
92 Master password revision code FFFE
93 Hardware reset value xxxx
95–99 ATA-reserved 0000

Total number of user-addressable LBA sectors available (see Section

100–103

2.1 for related information). These words are required for drives that
support the 48-bit addressing feature. Maximum value:
0000FFFFFFFFFFFFh.

104–107 ATA-reserved 0000

24 Barracuda XT Series SATA Product Manual, Rev. C

H

H

H

H

H

H

H

H

H

ST32000641AS = 3,907,029,168

H

Word Description Value

108–111 The mandatory value of the world wide name (WWN) for the drive.

NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit

Each drive will have a unique
value.

WWN support.
1 12–127 ATA-reserved 0000
128 Security status 0001

129–159 Seagate-reserved xxxx
160–254 ATA-reserved 0000
255 Integrity word xxA5

H
H

H

H
H

Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported

Note. See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data.

Description (if bit is set to 1)

Bit Word 63

0 Multiword DMA mode 0 is supported.
1 Multiword DMA mode 1 is supported.
2 Multiword DMA mode 2 is supported.
8 Multiword DMA mode 0 is currently active.
9 Multiword DMA mode 1 is currently active.
10 Multiword DMA mode 2 is currently active.

Bit Word 84

0 SMART error login is supported.
1 SMART self-test is supported.
2 Media serial number is supported.
3 Media Card Pass Through Command feature set is supported.
4 Streaming feature set is supported.
5 GPL feature set is supported.
6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported.
7 WRITE DMA QUEUED FUA EXT command is supported.
8 64-bit World Wide Name is supported.
9-10 Obsolete.
11-12 Reserved for TLC.
13 IDLE IMMEDIATE command with IUNLOAD feature is supported.
14 Shall be set to 1.
15 Shall be cleared to 0.

Bit Word 88

0 Ultra DMA mode 0 is supported.
1 Ultra DMA mode 1 is supported.

Barracuda XT Series SATA Product Manual, Rev. C 25

2 Ultra DMA mode 2 is supported.
3 Ultra DMA mode 3 is supported.
4 Ultra DMA mode 4 is supported.
5 Ultra DMA mode 5 is supported.
6 Ultra DMA mode 6 is supported.
8 Ultra DMA mode 0 is currently active.
9 Ultra DMA mode 1 is currently active.
10 Ultra DMA mode 2 is currently active.
11 Ultra DMA mode 3 is currently active.
12 Ultra DMA mode 4 is currently active.
13 Ultra DMA mode 5 is currently active.
14 Ultra DMA mode 6 is currently active.

26 Barracuda XT Series SATA Product Manual, Rev. C

4.3.2 Set Features command

This command controls the implementation of various features that the drive supports. When the drive receives this com­mand, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the
register does not represent a feature tha t the drive supports, the command is aborted. Power-on default has the read
look-ahead and write caching features enabled. The accept able values for the Features register are defined as follows:

Table 7: Set Features command values

02
03

10
55
82
90
AA
F1

Enable write cache (default).

H

Set transfer mode (based on value in Sector Count register).

H

Sector Count register values:
00

Set PIO mode to default (PIO mode 2).

H

01

Set PIO mode to default and disable IORDY (PIO mode 2).

H

08HPIO mode 0
09HPIO mode 1
0A

PIO mode 2

H

0BHPIO mode 3
0CHPIO mode 4 (default)
20

Multiword DMA mode 0

H

21HMultiword DMA mode 1
22HMultiword DMA mode 2
40

Ultra DMA mode 0

H

41HUltra DMA mode 1
42HUltra DMA mode 2
43

Ultra DMA mode 3

H

44HUltra DMA mode 4
45HUltra DMA mode 5
46

Ultra DMA mode 6

H

Enable use of SATA features

H

Disable read look-ahead (read cache) feature.

H

Disable write cache

H

Disable use of SATA features

H

Enable read look-ahead (read cache) feature (default).

H

Report full capacity available

H

Note. At power-on, or after a hardware or software reset, the default values of the features are as indicated above.

Barracuda XT Series SATA Product Manual, Rev. C 27

4.3.3 S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predeter­mined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely,
S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited
to the attributes the drive can m onit or. For more information on S.M. A.R.T. commands and implementation, see the Draft

ATA-5 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4

) that eliminates unnec-

H

essary drive returns. The diagnostic software ships with all new drives and is also available at:

http://seatools.sea

gate.com.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports
S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.

Table 8: S.M.A.R.T. commands

Code in features register S.M.A.R.T. command

D0
D2
D3
D4
D5
D6
D8
D9
DA

H
H
H
H
H
H
H
H
H

S.M.A.R.T. Read Data
S.M.A.R.T. Enable/Disable Attribute Autosave
S.M.A.R.T. Save Attribute Values
S.M.A.R.T. Execute Off-line Immediate (runs DST)
S.M.A.R.T. Read Log Sector
S.M.A.R.T. Write Log Sector
S.M.A.R.T. Enable Operations
S.M.A.R.T. Disable Operations
S.M.A.R.T. Return Status

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x 04 (abort) is writ-

ten to the Error register.

28 Barracuda XT Series SATA Product Manual, Rev. C

5.0 Seagate Technology support services

Internet

For information regarding Seagate products and services, visit www.sea
Worldwide support is available 24 hours daily by e-mail for your questions.

Presales Support:

[e-mail]

Technical Support:

[e-mail]

Warranty Support:

http://www.sea

mySeagate

my.sea

access to critical applications, personalized content and the tools that allow our p artners to ma nage their Seagate account
functions. Submit pricing requests, orders and returns through a single, password-protected Web interface-anytime, any­where in the world.

spp.seagate.com

spp.sea

for customized communications that are not available on the web. These communications contain product launch, EOL,
pricing, promotions and other channel-related information. To learn more about the benefits or to register, go to spp.sea-

gate.com, any time, from anywhere in the world.

gate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides self-ser vice

gate.com/www/en-us/support/warranty_&_returns_assistance

gate.com supports Seagate reseller s with product information, pro gram benefit s and sale s tools. You may register

gate.com.

Global Customer Support

Presales Support

Our Presales Support staf f can help you dete rmine which Seagate products are best suited for your specific application or
computer system, as well as product availability and compatibility.

Technical Support

Seagate technical support is available to assist you online at support.seagate.com or through one of our call centers.
Have your system configuration information and your "ST" model/product number available.

Barracuda XT Series SATA Product Manual, Rev. C 29

Customer Service Operations

Warranty Service

Seagate offers worldwide customer su pport for Seag ate product s. Seagate distributors, OEMs and other direct customer s
should contact their Seagate Customer Service Operations (CSO) representative for warranty-related issues. Resellers
or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have
your serial number and model or part number available.

Data Recovery Services

Seagate offers data recovery services for all forma t s and all b rands of stor age media. Our d at a r ecovery serv ices lab s are
currently located throughout the world. Additional information, including an online request form and data loss prevention
resources, is available at http://services.sea

gate.com/index.aspx.

Authorized Service Centers

Seagate Service Centers are available on a global basis for the return of defe ctive products.
See www.sea

gate.com for the service center near you.

USA/Canada/Latin America support services

For an extensive list of telephone numbers to technical support, presales and warranty service in USA/Canada/Latin
America, including business hours, go to the "Contact Us" page on www.sea

gate.com.

Global Customer Support

Presales, Technical, and Warranty Support
Call Center Toll-free Direct dial

USA, Canada,
and Mexico 1-800-SEAGATE [phone]

Data Recovery Services
Call Center Toll-free Direct dial FAX

USA, Canada, 1-800-475-0143 [phone]-475-0158
and Mexico [phone]

Europe, the Middle East and Africa Support Services

For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the Middle East
and Africa, go to the "Contact Us" page on www.sea

gate.com.

Asia/Pacific Support Services

For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific, go to the
"Contact Us" page on www.sea

gate.com.

30 Barracuda XT Series SATA Product Manual, Rev. C

Index

A

acceleration 11
acoustics 12
active mode 9
agency certification 13
altitude 10
ambient temperature 7, 10
areal density 5
ATA commands 21
Australia/New Zealand Standard AS/NZ CISPR22 14
Australian Communication Authority (ACA) 14
Australian C-Tick 14

B

buffer 6

C

cables and connectors 17
cache 6
capacity 5
case temperature 10
CE mark 13
certification 13
Check Power Mode 21
China RoHS directive 15
compatibility 13
conducted noise 9
conducted RF immunity 12
configuring and mounting the drive 16
connectors 17
corrosive environment 15
CSA60950-1 13
cylinders 5

Electromagnetic Compatibility (EMC) 13, 14
Electromagnetic Compatibility control Regulation 14
Electromagnetic Compatibility Directive (2004/108/EC)

13

electromagnetic immunity 12
electrostatic discharge (ESD) 12, 16
EN 55022, Class B 13
EN 55024 13
EN60950 13
enclosures 14
environmental specifications 10
error-correction algorithms 1
ESD 16
EU RoHS directive 15
European Union (EU) requirements 13
Execute Device Diagnostics 21

F

FCC verification 14
features 1
Flush Cache 21
Flush Cache Extended 21
Format Track 21
formatted capacity 5

G

geometry 5
Gs (acceleration of gravity) 11
guaranteed sectors 5

H

handling precautions 16
heads 5
height 6
humidity 10

D

data-transfer rates 1
DC power 7
default logical geometry 5
density 5
Device Configuration Freeze Lock 21
Device Configuration Identify 21
Device Configuration Restore 21
Device Configuration Set 21
Device Reset 21
dimensions 18
dissipation 7
Download Microcode 21

E

electrical fast transient 12

Barracuda XT Series SATA Product Manual, Rev. C 31

I

I/O data-transfer rate 5
Identify Device 21
Identify Device command 23
Idle 21
idle (DC power) 7
Idle Immediate 21
idle mode 7, 9
Information Technology Equipment (ITE) 13
Initialize Device Parameters 21
input noise ripple 9
input voltage 7
interface 5, 19
interference 14
internal data-transfer rate OD 5
ISO document 7779 12

K

Korean Communications Commission (KCC) 14
Korean Radio Research Laboratory (RRL) 14

L

LBA mode 5
length 6
logical geometry 5

M

master/slave 2
mounting 18

N

noise 9
nonoperating shock 11
nonoperating vibration 11

O

operating (DC power) 7
operating power 7
operating shock 11
operating vibration 11

P

perpendicular recording technology 1
physical characteristics 6
point-to-point 2, 17
power consumption 7
power dissipation 7
power management modes 9
power modes 9
power specifications 7
power-on to ready 6
precautions 16
printed circuit board 16
programmable power management 9
prominent discrete tone 12

Q

quick reference 3

R

Radiated RF immunity 12
radio and television interference 14
radio frequency (RF) 12
random seeks 7
Read Buffer 21
Read DMA 21
Read DMA Extended 21
Read DMA Without Retries 21

Read Log Ext 21
Read Multiple 21
Read Multiple Extended 21
Read Native Max Address 21
Read Native Max Address Extended 21
Read Sectors 21
Read Sectors Extended 21
Read Sectors Without Retries 21
Read Verify Sectors 21
Read Verify Sectors Extended 21
Read Verify Sectors Without Retries 21
read/write heads 5
read/write power 7
ready to spindle stop 6
Recalibrate 21
recording density 5
recording method 5
recording technology 5
relative humidity 10
reliability 13
RMS read/write current 9
RoHS 15
RRL 14

S

S.M.A.R.T. Disable Operations 22
S.M.A.R.T. Enable Operations 22
S.M.A.R.T. Enable/Disable Autosave 22
S.M.A.R.T. Execute Offline 22
S.M.A.R.T. implementation 21
S.M.A.R.T. Read Attribute Thresholds 22
S.M.A.R.T. Read Data 22
S.M.A.R.T. Read Log Sector 22
S.M.A.R.T. Return Status 22
S.M.A.R.T. Save Attribute Values 22
S.M.A.R.T. Write Log sector 22
safety certification 13
SATA ports 2
sectors 5
sectors per track 5
Security Disable Password 21
Security Erase Prepare 22
Security Erase Unit 22
Security Freeze 22
Security Set Password 22
Security Unlock 22
Seek 22
seek mode 7
seek time 6
Serial ATA (SATA) interface 19
servo electronics 7
Set Features 22
Set Max Address 22
Set Max Address Extended 22
Set Multiple Mode 22

32 Barracuda XT Series SATA Product Manual, Rev. C

shock 11
Sleep 22
sleep ( DC power) 7
sleep mode 9
sound 12
Specification summary table 3
spindle speed 5
spinup (DC power) 7
spinup power 7
Standby 22
standby (DC power) 7
Standby Immediate 22
standby mode 7, 9
standby timer 9
standby to ready 6
Start/stop times 6
static-discharge 16
subassembly 14
support services 29
surge immunity 12

T

technical support services 29
temperature 10
temperature gradient 10
timers (Idle and Standby) 9
track density 5

Write Uncorrectable 22

U

UL60950-1 13

V

vibration 11
voltage 7
voltage dips, interrupts 12
voltage tolerance 9

W

weight 6
wet bulb temperature 10
width 6
Write Buffer 22
Write DMA 22
Write DMA Extended 22
Write DMA FUA Extended 22
Write DMA Without Retries 22
Write Log Extended 22
Write Multiple 22
Write Multiple Extended 22
Write Multiple FUA Extended 22
Write Sectors 22
Write Sectors Extended 22
Write Sectors Without Retries 22

Barracuda XT Series SATA Product Manual, Rev. C 33

34 Barracuda XT Series SATA Product Manual, Rev. C

Seagate Technology LLC

920 Disc Drive, Scotts Valley, California 95066-4544, USA

Publication Number: 100586689, Rev. C, Printed in U.S.A.