Scott Plazma 4 Owner's Manual

Page 1
www.scot t-sport s.com
BIKE OWNER’S MANUAL 2015
All right s reserved © 2014 SC OTT Sports SA SCOTT Spo rts SA | 17 Route du Cro chet | 1762 Givisiez | Sw itzerland
Distrib ution: SSG (Europ e) Distrib ution Center SA P.E.D Zon e C1, Rue Du Kiel l 60 | 6790 Aubang e | Belgium
V4.3/19012015
Page 2
02
PLASMA 4 | BIKE OWNE R’S MA NUAL 2015 BIKE OWN ER’S M ANUAL 20 15 | PLASMA 4
03
www.scot t-sport s.com
ENGLISH
ENGLISH
The Plasma 4 C arbon bikes should be a djusted exac tly to the current ride r for reaching maximum s afety and performa nce while riding.
Please note that all adjustments should be done at your local SCOTT dealer or fo llowing to this manual.
CONTENT
Plasma 4 Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04
Geom et ry/ Technical Data Plasma 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05
Plasma 4 Frameset Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
Specific Torques Values Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
Rear Drop out and Derailleur Hanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07
BB Standard and FD Mount Standard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
Headset Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
BB Cable Guide and Cable Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
Seatpost and Seatube Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09
Storage Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Page 3
04
PLASMA 4 | BIKE OWNE R’S MA NUAL 2015 BIKE OWN ER’S M ANUAL 20 15 | PLASMA 4
05
ENGLISH
ENGLISH
PLASMA 4 CONCEPT
Plasma 4 is the re sult of research and develop ment based on the feedback of the SCOTT-triathlon and tim e trial athletes searching for one of the mos t efficient aerodynamics orientated yet affordable fra mes in the ma rket.
SCOTT’s focus was not only on the frame and rider aerod ynamics b ut also on the bike’s ergonomic side and a djustability as well as the frame fro nt end stiffness.
GEOMETRY/TECHNICAL DATA PLASMA 4
Headtube diameter Plasma 4 : 1.1/8”
BB housing PF BB 86
Rear brake SHIMANO direct mount
compatible brake calipers
Front brake Compatib le with both SHIMAN O
direct mo unt and single bolt f ront brake calipers.
Seat post s addle rails clamps
Differe nt seatpost saddl e rail clamps ar e available to m atch with your saddle: 7x7mm, 8x8.5 mm or 7x9.6mm
Rear hanger Compatib le Plasma 4 and Plasm a 5
Shifting Mechanical and electrical shifting
compatible
S/51 M/54 L/57 XL/60
A
HEAD TUBE ANGLE 72.0 ° 73.0 ° 7 3.0 ° 73 .5 °
B
HEAD TUB E LENGTH 100.0 mm 3.9 in 128.0 mm 5.0 in 159.0 mm 6 .3 in 19 9.0 mm 7.8 i n
C
TOP TUBE HORIZONTAL 526.0 mm 20.7 in 546.0 mm 21.5 in 56 6.0 mm 22.3 in 5 83.0 mm 23.0 in
D
STANDOVER HEIGHT 769.0 mm 3 0.3 in 799. 0 mm 31.5 in 829.0 mm 32.6 in 8 69.0 mm 34 .2 in
E
BB OFFSET -65.0 m m -2.6 in -65.0 mm -2.6 in - 65.0 mm -2 .6 in -65.0 mm -2.6 in
F
BB HEIGHT 269.0 mm 10 .6 in 269.0 mm 10.6 in 269.0 mm 10.6 in 269.0 mm 10.6 in
G
WHEEL BASE 965.0 mm 3 8.0 in 983 .0 mm 38.7 i n 1,009.0 mm 39.7 in 1,029.0 mm 40.5 in
H
BB CENTER TO TOP TUBE CENTER 504.9 mm 19.9 i n 53 4.7 mm 21.0 i n 564.4 mm 22. 2 in 604.2 mm 23.8 in
I
BB CENTER TO TOP O F SEATTUBE 519.9 mm 20.5 in 549.7 mm 21.6 in 579.4 m m 22.8 in 619.2 mm 24.4 in
J
SEATTUBE ANGLE 74.0 ° 75.0 ° 75.0 ° 76.0 °
K
CHAINSTAY MIN. 403.0 mm 15.9 in 403.0 mm 15 .9 in 403.0 mm 15.9 in 403.0 mm 15.9 in
L
REACH 383.0 mm 15 .1 in 400.0 mm 15.7 in 41 7.0 m m 1 6.4 in 430.0 mm 16.9 in
M
STAC K 500.0 mm 1 9.7 in 530.0 mm 20.9 in 560.0 mm 22.0 in 600.0 mm 23.6 in
N
STEM LENGTH
Page 4
06
PLASMA 4 | BIKE OWNE R’S MA NUAL 2015 BIKE OWN ER’S M ANUAL 20 15 | PLASMA 4
07
ENGLISH
ENGLISH
PLASMA 4 FRAMESET CONTENT
1. Frame
2. Fork
3. Headset
4. Seatpost
5. Storag e box
REAR DROP OUT AND DERAILLEUR HANGER
- Setup screw: Drop out length c an be set to adju st the rear wheel tire clearance with the frame ( 100) thanks to the rear dropout adjus tement screws . The chain stays length can b e set from 403mm to 413mm .
- Loos en the screw to set a longer chainstays length,
- Tighten the screw to set a shorter chai nstays length .
Make sure right a nd left side are set at the same length by assembling the rear wheel and verifying it is centred with the chainstays.
- Rear derailleur hanger: place the rear deraille ur hanger in the cavity and tighten the 2x M5 screws to th eir specif ied torques.
Rear derailleur hanger: SCOTT Part number 239178
Drop out a djustment screws: Stand ard M5*10mm headless sc rew availab le in any hardware shop.
SPECIFIC TORQUES VALUES TABLE
Page 5
08
PLASMA 4 | BIKE OWNE R’S MA NUAL 2015 BIKE OWN ER’S M ANUAL 20 15 | PLASMA 4
09
ENGLISH
ENGLISH
BB STANDARD AND FD MOUNT STANDARD
The BB standard on Plasma 4 is PF86.
FD Mount Standard: Brazed on standard same as other S COTT road frames: Solace, Addict or Foil.
HEADSET OPTIONS
Plasma 4 h eadset Syn cros Drop-In 1 1/8” black pa rt number: 238600
Bearing s stand ard: IS 41/28.6 | I S41/30
BB CABLE GUIDE AND CABLE ROUTING
BB cable guide set Plasma 4 Di2 + mechanical part numb er: 239179
SEATPOST AND SEATUBE CLAMP
SADDLE ASSEMBLY:
IMPORTANT
Before asse mbling the s addle, make sure the seatp ost saddl e rail clamps (524/525) are compatible with your saddle rails!
1. measure your s addle rails height and width (HxW)
2. Ritchey WCS Carbon One-Bolt Saddle Rail Clamp outer-pieces specifications should be compatible with your saddle rails
3. if the saddle rails dimensions you measured are d ifferent from the saddle clamps specifications, purchase the required saddle rail clamps parts at your retailer’s
4. following dimensions are available: 7x7mm, 8x8.5mm or 7x9.6mm
5. set the right s addle tilt and position the saddle rails so that the saddle rail cla mps are in the middle of the usable rail clamping area
6. tighten the M6 screw (527) to the specified torqu e (T13) to assemble the saddle
7. use the seatpost adjustment barrel to adjust your B B-Sadd le horizontal offset
8. once the right offset is set, tighten the two M5 barrel screws (521) to the specified torque (T12)
9. in some cases, you will nee d to remove the saddle to access the t wo M5 barrel screws.
Page 6
10
PLASMA 4 | BIKE OWNE R’S MA NUAL 2015 BIKE OWN ER’S M ANUAL 20 15 | PLASMA 4
11
ENGLISH
ENGLISH
SEATPOST ASSEMBLY:
IMPORTANT
Before asse mbling the seatpost into the frame, ma ke sure the rear side of the seatpost (side where head is longer) is at the rear e nd of the fram e
1. push gently th e seatpost into the frame
2. for electronic shifting: make sure the battery does n ot get stuck into the frame
3. once the desired seatpost height is achieved pre-a ssemble the seatpost we dge: position the upper wedge p art (505) over the mid wedge part (504) and the low wedge threaded part (5 03) below the mid wedge part
4. position the M6 wed ge screw (506) into the assem bly head up a nd pre-tighten it over 3 turns
5. position the wedge assembly into the seattube inse rt in front of the seattub e, its concave face should correspond to the seatpost front surface
6. tighten the M6 screw to the specified torque (T 11) while making sure the upper surface of th e wedge coincides with the upper surface of the top tub e.
Seatpost and seat clamp assembly a re fully compatib le betwee n Plasma 4 and Plasma 5 frames.
- Seatpost Pl asma 4/5 SCOT T part number: 239318
- Seat Clamp Pl asma 4/5 SCOT T part number: 239544
STORAGE BOX
Plasma 4 framesets an d complete bikes are delivered with an additional storage b ox that can be fitted to the top front end of the Toptube via 2 M5 A llen screws as sh own on the sketch be low.
Page 7
12
PLASMA 4 | BIKE OWNE R’S MA NUAL 2015 BIKE OWN ER’S M ANUAL 20 15 | PLASMA 4
13
ENGLISH
ENGLISH
SCOTT bikes are ma de using the m ost innovative pro duction a nd quality methods . They are equipp ed with best component s of well known parts supp liers.
Doing so SC OTT wa rrants its f rames and swingarms for five years (subject to compliance with maintenance ranges , see below) and S COTT forks (provid ed it is a fork of S COTT ) for two years for defects in material and/or workmanship in c ase of purchase of completely assembled bikes.
This warrant y of 5 years for the frames shall only be granted in case o nce a year a maintenan ce service h as been ef fected according to mainte nance requirements as set forth in this manual by an authorised S COTT dealer.
The authorised SCOT T dealer shall confirm the ef fected an nual maintenance ser vice by stamp and signature.
In case such an annual m aintenance service has not been ef fected the warranty of 5years for the frame shall be reduced to 3 years.
Costs for ma intenance a nd service have to be born by the owne r of the SCOT T bike .
On Gambler, Voltage Fr and Volt-X the warranty period is limited to 2 yea rs.
The warrant y period starts at the day of purchase. This warranty is limited to th e first buyer, what means the first pe rson who use s the bike and on ly with the use it was m ade for. Furthermore, this warranty is limited to purchases via a uthorized SCOTT-dealers
The warrant y is solely granted in case of purchase of a co mpletely assembled bike to the explicit exclusion of purchases of not completely assembled bikes.
In case of a warranty claim the decision to repair or to replace the defec tive part is up to SCOTT. Non defective parts will only be replaced at the guarantee’s own expense.
Fair wear and tear is not covered by the warranty.
A complete list of all parts of wear and tear c an be found in the next cha pter of this manual.
In addition , you will find at the end of this manual a protocol for the handing over of the bike which will remain in copy at the S COTT dealer after accept ance and sig nature of the consumer.
It is obligator y to show this protocol of handin g over together with th e defective part in case of a warranty claim given that it provides evidence of pu rchase. Otherwise no warranty is granted.
In principle, this warra nty is granted worldwide. Claims mus t be made thro ugh an authorized de aler, for information regarding the neare st dealer, write or call this comp any or the national SCOTT distributor.
Normal wear, accident, neglect, abuse, improper assembly, improper maintenance by other than an a uthorized dealer or use of p arts or devices not consistent with the use originally intended for the bicycle as so ld are not covered by this warranty.
Hereby SCOTT grants a voluntarily manufacturer’s warranty. Additional entitlements according to national warrant of merchantability are reserved .
For warranty info on the Fox Nud e shock ple ase refer to the at tached manual of Fox Nude.
Model .............................................................................
Yea r ...............................................................................
Size ................................................................................
Frame Nr. ..........................................................................
Shock Nr. ..........................................................................
Date of purchase ...................................................................
WARRANTY WARRANTY
Loading...