Scott PLASMA 4 User Manual

WWW.SCOTT-SPORTS.COM
WWW.SCOTT-SPORTS. COM
SCOTT Spor ts SA Route du Crochet 17, CH–1762 Givisiez Phone: +41 26 460 16 16 | Fax: +41 26 460 16 00 Email: scottsupport@scott-sports.com
All rights r eserved © 2016 S COTT Sports SA
v6.2/15122016
USER MANUAL
SCOTT PLASMA 4
www.scot t-sport s.com
ENGLISHENGLISH
The Plasma 4 C arbon bikes should be adjusted exactly to the current ride r for reachin g maximum safety and per formance while riding.
Please note that all adjustments shoul d be done at your local SCOTT dealer or following to this manual.
CONTENT
Plasma 4 Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04
Geom etry/ Technical Data Plasma 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05
Plasma 4 Frameset Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
Specific Torques Values Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
Rear Drop out and Derailleur Hanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07
BB Standard and FD Mount Standard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
Headset Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
BB Cable Guide and Cable Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
Seatpost and Seatube Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09
Storage Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Guarantee on S COTT Bikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
03 |
BIKE USE R MANUAL | PL ASMA 4PLASM A 4 | BIKE USER MANUAL
| 02
ENGLISHENGLISH
PLASMA 4 CONCEPT
Plasma 4 is the re sult of research and development based on th e feedback of the SCOTT-triathlon and tim e trial athletes searching for o ne of the most ef ficient aerodynamics orientated yet affordable frames in the market.
SCOTT’s focus was n ot only on the frame and rider aerodyna mics but also on the bike’s ergonomic side and adjustability as well as the f rame front end stiffness.
GEOMETRY/TECHNICAL DATA PLASMA 4
Headtube diameter Plasma 4 : 1.1/8”
BB housing PF BB 86
Rear brake SHIMANO direct mount
compatible brake calipers
Front brake Compatib le with both SHIMAN O
direct mo unt and single bolt f ront brake calipers.
Seat post s addle rails clamps
Differe nt seatpost saddl e rail clamps ar e available to ma tch with your saddle: 7x7mm, 8x8.5mm or 7x9.6mm
Rear hanger Compatib le Plasma 4 and Plasm a 5
Shifting Mechanical and electrical shifting
compatible
S/51 M/54 L/57 XL/60
A
HEAD TUBE ANGLE 72.0 ° 73.0 ° 7 3.0 ° 73 .5 °
B
HEAD TUB E LENGTH 100.0 mm 3.9 in 128.0 mm 5.0 in 159.0 mm 6 .3 in 19 9.0 mm 7.8 i n
C
TOP TUBE HORIZONTAL 526.0 mm 20.7 in 546.0 mm 21.5 in 56 6.0 mm 22.3 in 5 83.0 mm 23.0 in
D
STANDOVER HEIGHT 769.0 mm 3 0.3 in 799. 0 mm 31.5 in 829.0 mm 32.6 in 8 69.0 mm 34 .2 in
E
BB OFFSET -65.0 m m -2.6 in -65.0 mm -2.6 in - 65.0 mm -2 .6 in -65.0 mm -2.6 in
F
BB HEIGHT 269.0 mm 10 .6 in 269.0 mm 10 .6 in 269.0 mm 10.6 in 269.0 mm 10.6 in
G
WHEEL BASE 965.0 mm 3 8.0 in 983 .0 mm 38.7 i n 1,009.0 mm 39.7 in 1,029.0 mm 40.5 in
H
BB CENTER TO TOP TUBE CENTER 504.9 mm 19.9 i n 53 4.7 mm 21.0 i n 564.4 mm 22. 2 in 604.2 mm 23.8 in
I
BB CENTER TO TOP O F SEATTUBE 519.9 mm 20.5 in 549.7 mm 21.6 in 579.4 m m 22.8 in 619.2 mm 24.4 in
J
SEATTUBE ANGLE 74.0 ° 75.0 ° 75.0 ° 76.0 °
K
CHAINSTAY MIN. 403.0 mm 15.9 in 403.0 mm 15 .9 in 403.0 mm 15.9 in 403.0 mm 15.9 in
L
REACH 383.0 mm 15 .1 in 400.0 mm 15.7 in 41 7.0 m m 1 6.4 in 430.0 mm 16.9 in
M
STAC K 500.0 mm 1 9.7 in 530.0 mm 20.9 in 560.0 mm 22.0 in 600.0 mm 23.6 in
N
STEM LENGTH
05 |
BIKE USE R MANUAL | PL ASMA 4PLASM A 4 | BIKE USER MANUAL
| 04
ENGLISHENGLISH
PLASMA 4 FRAMESET CONTENT
1. Frame
2. Fork
3. Headset
4. Seatpost
5. Storag e box
REAR DROP OUT AND DERAILLEUR HANGER
- Setup screw: Drop out length can be set to adjust the rear whee l tire clearan ce with the frame ( 100) thank s to the rear dropo ut adjustem ent screws. The chainstays length can b e set from 403m m to 413mm.
- Loos en the screw to set a lon ger chains tays length,
- Tighten the screw to set a shorter chainstays length.
Make sure right a nd left sid e are set at the same length by asse mbling the rear wheel and verifying it is centred with the chainstays.
- Rear derailleur hanger: place the rear derailleur hanger in th e cavity and tig hten the 2x M5 screws to th eir specified torques.
Rear derailleur hanger: SCOTT Part number 239178
Drop out a djustm ent screws: Standa rd M5*10 mm headl ess screw available in any hardware shop.
SPECIFIC TORQUES VALUES TABLE
07 |
BIKE USE R MANUAL | PL ASMA 4PLASM A 4 | BIKE USER MANUAL
| 06
ENGLISHENGLISH
BB STANDARD AND FD MOUNT STANDARD
The BB standard on Plasma 4 is PF86.
FD Mount Standard: Brazed on standard same as other SCOTT road frames: Solace, Addict or Foil.
HEADSET OPTIONS
Plasma 4 h eadset Syncros Drop -In 1 1/8” b lack part number : 238600
Bearing s standard: IS41/2 8.6 | IS 41/30
BB CABLE GUIDE AND CABLE ROUTING
BB cable guide set Plasma 4 Di2 + m echanical part n umber: 2 39179
SEATPOST AND SEATUBE CLAMP
SADDLE ASSEMBLY:
IMPORTANT
Before asse mbling the saddle, make sure the seatpos t saddle rail clamps (524/525) are compatible with your saddle rails!
1. measure your s addle rails height and width (HxW)
2. Ritchey WCS Carbon One-Bolt Saddle Rail Clamp outer-pieces specifications should be compatible with your saddle rails
3. if the saddle rails dimensions you measured are dif ferent from the saddle clamps specifications, purchase the required saddle rail clamps parts at your retailer’s
4. following dimensions are available: 7x7mm, 8x8 .5mm o r 7x9.6mm
5. set the right s addle tilt an d position the saddle rails so that the saddl e rail clamps are in the middle of the usable rail clamping area
6. tighten the M6 screw (527) to the specified torque ( T13) to ass emble the saddle
7. use the seatpost adjustment barrel to adjust your BB-Saddle h orizontal off set
8. once the right offset is set, tighten the two M5 barrel screws (52 1) to the specified torque (T12)
9. in some cases, you will need to remove the saddle to access the two M5 barrel screws.
09 |
BIKE USE R MANUAL | PL ASMA 4PLASM A 4 | BIKE USER MANUAL
| 08
ENGLISHENGLISH
SEATPOST ASSEMBLY:
IMPORTANT
Before asse mbling the se atpost into the frame, make sure the rear side of th e seatpost (side where head is lon ger) is at the rear en d of the frame
1. push gently th e seatpost into th e frame
2. for electronic shifting: make sure the battery does not get stuck into the f rame
3. once the desired seatpos t height is ach ieved pre-assemble the seatpost wedge: position the upper wedge part (505) over th e mid wedge part (504) and the low wedge threaded part (503) below the mid wedge par t
4. position the M6 wed ge screw (506) into the assemb ly head up and pre-tighten it over 3 turns
5. position the wedge assem bly into the seattube inser t in front of the se attube, its concave face should corresp ond to the seatpost front surface
6. tighten the M6 screw to the specifie d torque (T 11) while ma king sure the up per surface of th e wedge coincides with the upp er surface of the top tube.
Seatpost and seatclamp ass embly are fully compatible between Plasma 4 and Plasma 5 frames.
- Seatpost Plasma 4/5 SCOTT part number: 239318
- Seat Clamp Plasma 4/5 SCOTT part number: 239544
STORAGE BOX
Plasma 4 framesets and complete bikes are delivered with an additional s torage box that can be fitted to the top front e nd of the Toptube via 2 M5 Allen screws as shown on the sketch be low.
11 |
BIKE USE R MANUAL | PL ASMA 4PLASM A 4 | BIKE USER MANUAL
| 10
SCOTT Bikes
Gambler, Voltage FR, Volt-X
5
ENGLISHENGLISH
limited warranty does not cover purchases of n ot completely assembled b ikes. This limited warranty does not cover any defect ca used by “wear and tear” (a complete lis t of all parts of “wear and tear” can be found in the gen eral manual that came with your bike), accident, neglect, improper handling, colo ur fade due to exp osure to sunlight, abuse, misuse, an act of God, improper assembly, non-compliance with recommended maintenance and care procedures, improper or incorrectly performed maintenance or repairs pe rformed by so meone othe r than an authorized SCOT T dealer, use of pa rts or devices not consistent with the Product, and alteration of the Product.
All Produc ts come with a manual; please carefully fo llow the instru ctions loc ated there or affixed e lsewhere to the Product. To the extent permitted by law, consequential and incidental damages a re not recoverable under this limited warrant y.
How do you make a claim under this lim ited warra nty?
To make a claim under this limited warranty, you must notif y SCOTT of the claimed d efect within the warra nty period and timely retu rn the Produc t to SCOT T at your expense for inspection. Please contact your a uthorized SC OTT dealer, call SCOTT ’s customer service or the national SCOTT distributor (dealer locator: www.scott-sports.com). All returned Products must be accompanied by proof of purchase (receipt) from an authorized SCOTT dealer or thi s limited warranty will not app ly. In case of repla cement or ref und, returned Pro duct becomes the prope rty of S COT T.
A protocol for the handing over of the Product (which you will find at the end of the manual) will remain in copy at the SCOTT dealer after acceptance and signature of the consume r. It is obligatory to show this protocol of ha nding over togeth er with the defective part in case of a warranty claim given that it provide s evidence of purchase or this limited warranty will not a pply.
How do state laws affec t your right s under this limited warrant y?
This limited warranty gives you specific legal rights, and you may also have other rights, which vary f rom state to state.
Recommendation
We strongly recommend that you use only authorized SCOTT dealers for yearly maintenance services and for repairs, as improper or incorrectly performed maintenance or repairs voids this limited warranty. Costs fo r maintenan ce service have to be borne by the consumer.
WARNING!
SCOTT Spor ts SA is not res ponsib le or liable for any injury cau sed by any missing complia nce with th ese inst ructions, particularly but not lim ited to mis use, inco rrect maintenance, incorrect set-up and handlin g, neglect or abuse. Failure to follow these instructions can result in component failure, serious personal injury. Component failure can lead to loss of control of the bi cycle and result in serious personal injury.
What is Covered?
This warrant y covers defects in materials and workman ship at the time of transfer of risks in frames , swingarms and forks (provided it is a fork of SCOT T) on SCOTT branded bikes sold completely assembled by SCOT T or an authorized SCOTT dealer (“Product”).
How long do es coverage las t?
This voluntary manufacturer’s warranty is limited to five years for frames and swingarms, respectively two years for forks, from the d ate of purchase of th e Product and is limited to the first purchaser of the Product and subject to the prior registration of your SCOTT bike on www.scott-sports .com within 10 days as of the date of purchase. Transfer of the Produc t from the firs t purchaser to another per son terminates this limited warranty. The limited warranty of five years for the fram es and swingarms shall on ly be granted in case once a year a maintenance service has been effected according to maintena nce requirements as set for th in the manual. The effected annual maintena nce service shall be confirmed by stamp and signature. In c ase such an annual maintenance ser vice has not been ef fected the wa rranty of five yea rs for the frame shall be red uced to three years. Costs for ma intenance and service have to be borne by the owner of the Product.
On Gambler, Voltage FR and Volt-X the warranty pe riod is limited to t wo years.
Repaired or replaced Products are covered for the remainder of the original warranty period and subject to the conditions outlined in the original warra nty, to the extent permitted by law.
Hereby SCOTT grants a worldwide voluntarily manufacturer ’s warranty. To the extent permitted by law and unless a shorter duration is stipulated by law, any warranties implied by law are limited in duration to maximum five, respectively two years, f rom the date of purchase of the Product and are limited to th e first purchaser of the Product.
What will SCOTT do?
SCOTT will replace or re pair any defective Product, or will refund your purchase price (as evidenced by your tendered receipt of purchas e of the Produc t), at SCOTT ’s option. You must pay charges in connection with replacement of any non-defective parts . In such a case, you will b e alerted to the advisability of replacing non-defective parts, so you can pre-autho rize the costs.
What does t his limi ted warran ty not cover?
This limited warranty doe s not cover defect s which did not exist before the tra nsfer of risks. This limited warranty does not cover Products used in rental o perations . This
GUARANTEE ON SCOTT BIKES
13 |
BIKE USE R MANUAL | PL ASMA 4PLASM A 4 | BIKE USER MANUAL
| 12
Loading...