Scotsman Ice Machine HD22 Installation Manual
HD22 and HD30
Introduction
To the owner or user: This product manual is a
source of information about the installation, start
up, cleaning, maintenance and repair of the
product.
Table of Contents
Introduction ················································· Page 1
General Description ············································· Page 2
Specifications & Limitations ········································· Page 3
HD30 Dimensioned Illustration ······································· Page 4
HD22 Dimensioned Illustration ······································· Page 5
Product Description ············································· Page 6
Unpacking ·················································· Page 7
Installation - Plumbing ··········································· Page 8
Installation - Electrical and Ice Machine Assembly ····························· Page 9
Final Check List/Initial Start Up ······································· Page 10
Use ····················································· Page 11
General Care and Cleaning ········································· Page 12
General Care And Cleaning - Continued ·································· Page 13
Maintenance ················································ Page 14
Adjustments ················································· Page 15
Service Diagnosis ·············································· Page 16
September 2003
Page 1
HD22 and HD30
General Description
The HD22 is a hotel/motel ice dispenser. It is
designed to use a Scotsman C0322 or C0522
cube ice machine as the source for ice.
The HD30 is a wider version of the HD22 and is
designed to use a Scotsman C0330 or C0530
Ice from the cuber falls into the insulated hopper,
where it is stored until needed. When a user
pushes the dispense chute a rotating wheel
scoops the ice up to the top front of the hopper
where there is an outlet to the ice chute.
cuber as its source of ice. Additional models may
be used, see sales information for details. Flaked
or nugget ice is not recommended for use in these
dispensers.
Cuber Model Fits Dispenser Adapter
C0322 or CME306 HD22 None Needed
C0522 or CME456 HD22 None Needed
C0330 or CME256* HD30 None Needed
C0530 or CME506* HD30 None Needed
EH222 or CME686 or CME810 HD22 KBT36
EH222 or CME686 or CME810 HD30 KBT32
* Higher capacity cubers, C0630 or C0830, may also be used, but they require 230 volt power.
New dispenser / used ice machine combinations: Some of the ice machines listed in the table above
used a thermostat when on a dispenser. When re-using the ice machine on an HD22 or HD30, disconnect
and do not use the thermostat.
Prior cubers, CM250, CME250, CM500, CME500, SLC300, SLE300, SLC400, SCE400 are not compatible
with either HD22 or HD30 unless the bin thermostat is used and a thermostat bracket is installed. CM
products use bracket A32262-001, SLC/SLE products use bracket C34196202.
Basic Specifications
Model Dimensions
w”xh”xd”
with 6” leg
HD22B-1A 22 x 53 x 33 ½ 115/60/1 Basic 22” model, 60 Hz 120 lb
HD22B-6A 22 x 53 x 33 ½ 230/50/1 Basic 22” model, 50 Hz 120 lb
HD30B-1A 30 x 53 x 33 ½ 115/60/1 Basic 22” model, 60 Hz 180 lb
HD30N-1A 30 x 53 x 33 ½ 115/60/1 Coin/token model 180 lb
HD30W-1A 30 x 53 x 33 ½ 115/60/1 Water station model 180 lb
HD30B-6A 30 x 53 x 33 ½ 230/50/1 Basic 30” model, 50 Hz 180 lb
Basic Electrical
volts/hertz/phase
Model Description Bin Storage
Capacity, ARI rated
All 60 Hz models are supplied with an 11’ power cord, 50 Hz models have a 1.1 meter power cord. Basic
models dispense ice when their chute is pushed. Coin/token models require a coin or token for dispense
activation. Tokens are available from Scotsman, the part number for 500 tokens is KTOKEN. Water station
models are basic models with a separate non-refrigerated water dispense station.
March 2009
Page 2
Specifications & Limitations
HD22 and HD30
This dispenser is designed to be installed and
operated indoors, in a controlled environment. Its
minimum and maximum operating temperature
limits are the same as those for the ice machine.
Minimum Maximum
o
Air Temp 50
Voltage 60 Hz 104 126
Check the nameplate, located on the back of the
cabinet for specific information.
Scotsman reserves the right to make design
changes and/or improvements at any time.
Specifications and designs are subject to change
without notice.
Scotsman assumes no liability or responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the
use of any parts and/or other components not
specifically approved by Scotsman.
F. 100oF.
Kits:
A bin top adapter kit is also available to allow
placement of a Scotsman EH222, CME686 or
CME810 Eclipse ice making head on the
dispenser.
The HD22s kit number is KBT36.
·
The HD30s kit number is KBT32.
·
There is also a kit that can be installed on a
HD30N (coin operated model). That kit is a coin
counting timer that can be adjusted to accept more
than one quarter before activating the dispense
mechanism. The kit’s part number is 12-2909-21.
No other kits are available.
Models
There are three versions of the HD30 dispensers:
Basic, Coin/token and Water Station. The Basic
version is constructed to deliver ice when the ice
chute is pushed in, and it continues to vend ice as
long as the ice chute is held in.
The Coin/token version is designed to deliver ice
after a coin or token is inserted into the coin slot
AND then the ice chute is pushed in. Ice vending is
limited to a preset time per coin or token use.
Coins or tokens are collected in a coin box at the
bottom of the dispenser. A keyed door allows
access to the coin box without removing the front
panel.
The Water Station version is a Basic version with a
mechanical water faucet added to the left of the ice
chute. Water is dispensed whenever the faucet
lever is pushed back. The HD30 is available in all
versions, the HD22 is only available as a Basic
model.
50 Hz.
The Basic models of the HD22 and HD30 are
available in 230 volt 50 Hz electrical for those
countries with that type of electrical service.
March 2009
Page 3
HD22 and HD30
HD30 Dimensioned Illustration
ICE HEAD MOUNTING
451.1
17 3/4"
179.1
7"
189.4
7 1/2"
3/4 FPT
DRAIN
BACK
189.7
7 1/2"
(2) 5/16-18 UNC
24.1
1"
POWER
CORD
WATER INLET
3/8 FLARE
(WATER FILLER ONLY)
444.4
17 1/2"
254.8
10"
WATER VALVE HEIGHT
(WATER FILLER ONLY)
ICE
HEAD
762.4
30"
711.2
28"
Note: Ice fill station depth is
curved to match large ice
buckets. Listed number is
the maximum depth.
ICE FILL STATION
8 3/4 [221.5] HIEGHT
13 1/2 [342.9] WIDTH
8 1/2 [215.9] DEPTH
1351.3
53 1/4"
650.5
25 5/8"
609.6
24"
ICE
HEAD
2062.5
81 1/4"
FRONT
152.4
6"
September 2003
Page 4
849.4
33 1/2"
RIGHT SIDE
HD22 Dimensioned Illustration
(2) 5/16-18 UNC
ICE HEAD MOUNTING
24.1
POWER
CORD
1"
179.1
7"
88.9
3 1/2"
406.4
16"
3/4 FPT
DRAIN
HD22 and HD30
BACK
558.8
22"
ICE
HEAD
711.200
28"
Note: Ice fill station depth is
curved to match large ice
buckets. Listed number is
the maximum depth.
ICE FILL STATION
8 3/4 [221.5] HIEGHT
13 1/2 [342.9] WIDTH
8 1/2 [215.9] DEPTH
1351.3
53 1/4"
650.6
25 5/8"
609.6
24"
ICE
HEAD
2062.5
81 1/4"
FRONT
152.4
6"
September 2003
Page 5
850.1
33 1/2"
RIGHT SIDE
Loading...