Schwinn Runabout Trailer Owner's Manual
Runabout
Model 13-SC250/SC350 Trailer
Owner’s Manual
Please keep this Owner’s Manual for future reference. If you sell or give this product away, please include this
Owner’s Manual, and ask the new owner to read the instructions completely before operating.
PRIOR TO ASSEMBLY:
Please read this Owner’s Manual completely before assembling or operating this product.
Assembly of this product should be carried out by an adult.
Parts are wrapped in paper or protective covering to prevent damage during shipment. Remove all parts and
packing materials from the box prior to assembly. Save all packing materials until assembly is complete to
make sure no parts are accidentally thrown away. After assembly is complete, properly discard all waste.
Refer to the Parts List and Diagram on page two of this manual to make sure all parts are accounted for.
Do not return this product to the store! If any parts are missing or damaged, please contact one of our
Customer Service Representatives by phone at 1-800-242-6110, or by e-mail at Info@instep.net.
IMPORTANT SAFETY INFORMATION:
WARNING Always wear an approved safety helmet when riding!
WARNING Never leave your child unattended on this product!
WARNING This trailer bike is designed to attach to an adult bicycle with 26”, 27”, or 700C wheels!
WARNING This trailer bike does not have a brake. Make sure the adult bike brakes function properly!
WARNING Recommended for ages 4 through 9! Maximum weight capacity of rider is 75 pounds!
WARNING Make sure the child riding the trailer bike understands how to operate it correctly!
WARNING Always use the safety flag when riding with this product!
WARNING A bicycle with the trailer bike attached requires a wide turning radius! Use caution when turning!
WARNING Do not ride over curbs! Avoid bumps and potholes! Do not turn sharply!
WARNING Before riding, check that all parts are assembled correctly per the manufacturer’s instructions!
WARNING Tire should be inflated to the pressure reading shown on the tire sidewall! Check before each use!
WARNING Use a foot pump or hand pump to inflate tires! Pressurized air hoses can cause overinflation!
WARNING Do not ride at night!
WARNING Do not ride barefoot!
WARNING Do not ride in wet weather or when road surface is slippery!
WARNING Periodically re-check all fasteners to make sure they are tight!
TOOLS REQUIRED FOR ASSEMBLY:
Adjustable wrench
6mm Allen wrench
5mm Allen wrench
1
FULLY ASSEMBLED TRAILER BIKE
PARTS LIST
QTY DESCRIPTION QTY DESCRIPTION
1 Frame w/ folding trailer arm, wheel, 1 Seat post assembly w/ seat,
chain (w/ guard), crank red rear reflector and bracket
1 Coupler assembly 1 Left pedal
1 Handlebar w/grips and pad w/cover 1 Right pedal
1 Frame pivot bolt 1 Safety flag w/ poles and joiner
1 Frame quick release
IMPORTANT!
We appreciate your purchase of this product, and hope you will be completely satisfied with
your selection. Although great care has been taken to assure the highest quality, some
problems may occur. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE! To
ensure prompt and correct handling of your problem, or to answer any questions you may
have, please contact our Toll-Free Customer Service Number listed below. Please have the
model number (found on carton or manual) and assembly instructions ready when calling. If
neither is available, please tell us the name of the product in question.
For questions concerning the safe use of this product, please contact Schwinn at
1-800-242-6110
E-mail: info@instep.net Web site: www.instep.net
2
ASSEMBLY AND OPERATING INSTRUCTIONS
Open carton, remove contents, and compare contents with parts list
Note: To prevent scratching of the frame, it is recommended that you lay the parts out on top
of a flattened cardboard box, or other soft surface.
1. Remove all contents from the carton. Check to make sure nothing is left in the box.
2. Unwrap all parts and compare them with the parts list and the above picture. Make sure
nothing is missing.
STEP 1 Attaching the folding trailer arm
1B
1A
1A. Position the trailer arm to the Runabout frame as shown. Line up the three holes to
begin assembling the hinge.
1B. Insert the receiving half of the frame pivot bolt through the three holes and insert the
screw to the pivot bolt. Use the Allen wrench to tighten.
3
Loading...