Schwaiger HA101 User manual
HA101
GATEWAY
CONTROL CENTER
USER MANUAL
SCHWAIGER
HOME
Dimming
HOME AUTOMATION
Temperature
LightSmoke
MotionRadiator
Flood
Blinds
Congratulations and thank you for purchasing the HA101 Schwaiger Product. The following product description will provide you with
useful information about its use.
ATTENTION !
Note regarding the integration of a new Gateway:
In order to add the Gateway to your account, please
use the password and the security ID given on page 33
of this user manual.
Internet: www.schwaiger.de
Service-Hotline: +49 9101 702-199
2
TABLE OF CONTENTS
1 PRODUCT DESCRIPTION ..................................................................................... 4
2 HA101 GATEWAY ................................................................................................ 5
3 TECHNICAL INFORMATION ................................................................................. 6
4 CONFIGURING THE SCHWAIGER HOME SYSTEM ................................................. 6
4.1 CONNECTING THE GATEWAYS TO HOME NETWORK ..............................................6
4.2 REGISTERING THE USER’S ACCOUNT ................................................................. 6
4.3 ADDING THE GATEWAY TO THE USER ACCOUNT ..................................................7
4.4 HOME-INSTALLATION ....................................................................................... 7
4.5 MANAGING Z-WAVE-COMPONENTS ...................................................................8
4.6 ZIGBEE COMPONENTS ......................................................................................8
4.7 RESETTING THE GATEWAY, NETWORK AND FACTORY SETTINGS ............................. 8
4.8 HA101 BUTTON ASSIGNMENTS ..........................................................................9
5 CLIENT APPLICATION MANUAL ......................................................................... 10
5.1 ACCOUNT MANAGEMENT ................................................................................10
5.1.1 Creating a new account ......................................................................... 10
5.1.2 Updating account information ................................................................. 12
5.2 HOME CONFIGURATION .................................................................................. 14
5.2.1 Adding a gateway to the account ............................................................ 14
5.2.2 Removing a gateway from an account ..................................................... 16
5.2.3 Home installation ................................................................................. 17
5.2.4 Device management ............................................................................. 18
5.2.4.1 Adding a new device.................................................................. 20
5.2.4.2 Removing a device .................................................................... 20
5.2.4.3 Removing a device from a previous network ................................. 20
5.2.4.4 Updating the device name and location ........................................ 20
5.2.4.5 Expanding functional access in learning mode ............................... 20
5.2.4.6 Setting the timeframe for registration & deregistration ................... 21
5.3 CONTROLLING DEVICES .................................................................................21
5.3.1 Controlling devices by type .................................................................... 21
5.3.2 Controlling devices by location ............................................................... 22
5.3.3 Advanced device configuration ............................................................... 23
5.4 CONFIGURING SCENARIOS .............................................................................23
5.4.1 Creating New Scenarios ......................................................................... 24
5.4.2 Executing a scenario ............................................................................. 26
5.4.3 Editing a scenario ................................................................................. 27
5.4.4 Deleting a scenario ............................................................................... 27
5.4.5 Disabling a scenario .............................................................................. 27
5.4.6 Enabling email notification ..................................................................... 27
Compatible components ........................................................................................ 28
3
1 PRODUCTION DESCRIPTION
The Schwaiger Home app is a complete solution for intelligent living, which uses a variety
of communications options for controlling household equipment. Access to the home system
is assured through the use of cloud services and the user-friendly mobile control interface.
Cloud
Overview of the Schwaiger Home network
Please Notice!
The Schwaiger application is constantly being further developed
and improved. Please make sure that you are using the latest
version of the user manual, which can be downloaded from our
website www.schwaiger.de
4
2 HA101 GATEWAY
The HA101 gateway is the device that provides support for the home automation (HA)
features. The gateway can control all of the home automation devices in the user’s home, such
as the alarms, thermostats and more. The gateway will control devices that support one of the
following communication protocols: Z-Wave, ZigBee.
It can query the status of the device in the home network and save it, as well as change the
status and all configuration options.
Includes Plug adapter
for Schuko wall sockets
free
download on
or
The gateway is controlled from the client application, which can be downloaded to iOS 7.0 or
later (Apple devices) or devices equipped with Android 4.0 or later. The app can be downloaded
from the Apple Store and from Android Play, where it can be found using the Schwaiger name
as the key word for searches.
With the client applications, users can control their household devices and manage their accounts as well as the list of their gateways and configuration options.
A cloud-based web application has also been made available for remote access through the
gateway. Using this application, users can manage their account and their gateway updates.
The cloud service can be found at https://home.schwaiger.de
The gateway has three buttons.
• Button 1 is used to add and remove Z-Wave devices.
• Button 2 is used to add ZigBee devices.
• Button 3 is used to restart the gateway, reset the gateway network and reset the
factory default settings.
The use of these buttons will be described in more detail in the corresponding sections of this
manual (Page 9).
5
3 TECHNICAL INFORMATION
Hardware Specifications
• Electrical: ~100-240 V, 0.6 A, 50/60 Hz (only inside the home, up to a max. of 40° C)
• Gateway connections using Ethernet and WLAN
• Sensor connections using the Z-Wave and ZigBee protocols
• LED-illuminated button for configuring devices
• Status LED (dimmable)
• USB port for (no function)
4 CONFIGURING THE SCHWAIGER HOME SYSTEM
Configuring the Schwaiger Home system consists of four basic steps.
1. Connecting the gateways to the home network
2. Registering the user’s account
3. Adding the gateway to the user account
4. Home installation
4.1 CONNECTING THE GATEWAYS TO THE HOME NETWORK
The gateway will be connected to the local home network with the help of Ethernet or WLAN
connections. Once connected with the wall, the gateway will start operations (after 2 min.) and
connect to the home network with the help of Ethernet connections, if the connected Ethernet
RJ45 cables are working. If an Ethernet cable is not available, the gateway will start in WLAN
Access Point mode, which is only used to configure the wireless network. All three LEDs will
blink as long as the gateway in is Access Point mode.
Connect the smartphone or tablet with the gateway access point to access the gateway confi
guration page. The SSID for the gateway has been assigned an identifier that will be displayed
using the identifier “SSID:Schwaiger...”. Create a connection to the access point and enter
„http://192.168.0.1” or „http://HA101” as the URL in the browser for the smartphone or
tablet. The page that opens will allow an SSID and the password for the home network’s router
to be entered (Notice the correct spelling!). Internet connection
will be required in order to register the gateway with the cloud
service. The gateway can only be enabled and afterwards recei
ve software updates.
-
-
4.2 REGISTERING THE USER’S ACCOUNT
Users can authenticate gateways and mobile apps with the
Schwaiger Home System using the user account. The user
name for the account will be the email address that is required
for registering the account. Account registration may be done
through the client or the web application from https://home.
schwaiger.de.
To create a user account using the client application, the user
must first make sure that their smartphone or tablet is connec
ted to the local wireless network (WLAN). The Schwaiger Home
app can then be started. Choose the Create New Account option
on the login dialog and follow the setup wizard’s instructions.
Schwaiger Home will ask for a valid email address to be entered as the user name. This email
address will be used to send a link to activate the account. Additional legal information will
be provided after tapping on the General Business Terms and Conditions and Data Protection
Provisions link. Confirm the usage conditions to continue.
-
6
Additional account and personal information will be entered as part of following those instructions. Entry of all information regarding the account details is optional. It may be changed at
any time. The asterisk (*) indicates mandatory entries.
Upon completion, the account registration information will be sent to the cloud service. Once
the user name and password have been validated, an activation link will be sent to the user
by email. It may be several minutes before that email message arrives. Confirm the activation
of the account by tapping the link in the message. (Check your Spam folder, just to be sure.)
Additional information about account registration through the cloud application can be found
in Section 5.1. (from page 10)
4.3 ADDING THE GATEWAY TO THE USER ACCOUNT
Either a mobile application or a cloud service can be used to associate a gateway with a user
account. To make the association using a mobile application, open the Schwaiger Home app
and log into the user account. Select the Home Installation option from the main menu. On the
subsequent Home Installation screen, select the Add Gateway option in the upper right corner.
The new Gateway wizard will start and request a gateway SSID (secure SID), a password and
a symbolic gateway name. (Page 15)
The PWD (Password) is a unique identifier for every gateway device. It will
consist of 12 characters (e.g. as 7CDD907E2AA3) and can be found on the
device and in it packaging.
The SID (Secure ID) is a unique, secret identifier for a gateway. It will consist
of 16 characters (e.g. 000000012H5J93AC). This number can be found on the
last page of the operating instructions.
This number can be found on the last page of the manual.
As soon as the required information has been entered, tap the button to continue
the gateway’s SID has been compared with others in the cloud and has not been assigned to
another user account, the gateway will be added.
The gateway must be connected with the same local network used with the Home Installation
wizard.
Additional information about adding a gateway to an account through the client application can
be found in Section 5.2.1. (Page 14)
. Once
4.4 Home-Installation
The Gateway Configuration option will become available after tapping the Home Installation
option on the client’s main menu. To make the Options menu appear, tap and hold the Gateway
button on the Home Installation screen. Select the Edit option from that menu. The option will
start the Gateway Configuration wizard.
In the first step, the user can change the gateway name. The gateway SID cannot be changed
once it has been added to the user account Tap the
Assignments step.
The user can manage the associated floors and rooms in a subsequent step. Adding the floors
and rooms can be accessed by tapping the + option in the upper right corner. Tapping this con
trol and holding it for a moment can remove each room and each floor. Once the user is happy
with the home assignments, tap the
button to continue to the Device Management step.
button to continue to the Setup Home
-
7
In this step, the user can add new devices by tapping the Find Devices button. This action will
place all networks in a mode, which can add devices. Read the operating instructions for the
selected components to do so. From the same screen, devices can be removed by tapping the
device and holding it for a longer time, and then selecting the Delete option (regarding this,
see the respective operating instructions).
Z-Wave devices that have not been removed from the previous network must
be removed first. This can be done using the Remove Device option on the
Settings menu
Once the configuration of the gateway has been completed, tap the
Home Installation wizard process.
Additional information about configuring a gateway and mobile device through the mobile app
can be found in Section 5.2.
in the upper right corner of the screen. (see page 18, Ill. 16)
button to complete the
4.5 MANAGING Z-WAVE-COMPONENTS
Please note, that the distance between the gateway and the clients shall not be more
than 0.5 meters during integrating in/excluding from the network.
Adding components using the mobile applications
To do this, tap the Home Installation option on the mobile application’s main menu and select
the device button by tapping it and holding it for a period. Go to Add Device to introduce a new
component. If the network has been opened for integration (Find Devices), the LED will stop
blinking and stay in the lit state. The user must connect the device during this period to add
the Z-Wave device. To do so, follow the instructions in the device’s manual.
Removing components using the mobile applications
To do this, tap the Home Installation option on the mobile application’s main menu and select
the device button by tapping it and holding it for a period. (see Image 13). Tap the Add Device
option. Select the Remove Device option from the Settings
of the screen. The corresponding Z-Wave device must be removed from the network during the
period indicated on the screen. To do so, follow the instructions in the respective user’s guide.
Adding components using the gateway
To add device to the Z-Wave network, the user must tap the 1 button and hold it for one to
five seconds. The Z-Wave network will then open for the integration process. During that time,
the LED will blink once per second. The user must connect the device during this period to add
the Z-Wave device. To do so, follow the instructions in the device’s manual. The network will
be closed when the button is tapped and held for five to ten seconds. During that time, the
LED will blink four times per second. Once the network has been closed, the LED will turn off.
Removing components using the gateway
The network will be opened for removing devices when the button is tapped and held for
roughly 10 to 20 seconds. During that time, the LED will blink ten times per second. The cor
responding Z-Wave device must be removed from the network during the period indicated on
the screen. To do so, follow the instructions in the respective user’s guide.
menu in the upper right corner
-
4.6 ZIGBEE COMPONENTS
Adding ZigBee devices is done in the same manner as Z-Wave devices. The only difference is
that the 2 button must be used.
4.7 RESETTING THE GATEWAY, NETWORK AND FACTORY SETTINGS
Re-start the gateway
Tapping the 3 button (and holding it for 1 to 5 seconds) will restart the gateway without affec
ting the existing configuration.
8
-
Re-start the network
This function will permit the user to reset the network connection settings to factory settings.
Once the network has been restarted, the gateway will be restarted. Once the network cable
has been connected to the gateway after the network has been restarted, it will continue to
use the network connection. If the network cable has not been connected to the gateway, the
gateway will enter Access Point mode. Tapping the 3 button and holding it for 5 to 15 seconds
will reset the network configuration.
Factory settings
The factory settings function will reset the gateway to the state in which it was delivered. Doing
so will delete all of the saved data. Furthermore, all saved Z-Wave and ZigBee settings will be
deleted as well as the scenarios already created. Tapping the 3 button and holding it for 15 to
30 seconds will reset to the factory settings.
4.8 HA101 Button Assignments
The HA101 gateway has 3 buttons (numbered in sequence), which have each been assigned
an LED. Certain features will be activated by tapping and holding the button for longer periods
of time. Each buttons has been assigned a special feature.
• Button 1: Managing the Z-Wave network
• Button 2: Managing the ZigBee network
• Button 3: System settings (reset)
Z-Wave learning mode
To enable the Schwaiger Home Gateway to add a new Z-Wave sensor, select learning mode.
Tap the 1 button for Z-Wave components and hold it for 1 to 5 seconds to start learning mode.
If a Z-Wave sensor should be removed, tap the 1 button (and hold it for 10 to 30 sec.) to
remove the components from the gateway.
ZigBee learning mode
Follow the same procedure for the Z-Wave mode in order to register ZigBee components. Of
course, the 2 button will be used for this feature (see the tables as well). The LEDs also provide
information about the status of the gateway.
0Sec. 1 5 10 15 20 30
Green
Button 1
Z-WaveZigBeeSystem
Blinks 2Hz
until network
is opened
Open network
Blinks 4Hz
until network
is closed
Blinks 10Hz
until network
is closed
Open network
for exclusion
Blinks 20Hz
Learn modeClose network
Blinks 2Hz
until network
Green
is opened
Open network
Button 2Button 3
Blinks 2Hz
Green
Reset Reset network
In the Access Point mode, all three LEDs will be turned on at a frequency of 2 Hertz. When
starting the gateway, only the LED for the 1 Button will be turned on. Booting takes roughly
2 minutes.
Blinks 4Hz
until network
is closed
Close network
Blinks 4Hz Blinks 10Hz
Factory reset
9
5 CLIENT APPLICATION MANUAL
5.1 ACCOUNT MANAGEMENT
5.1.1 Creating a new account
Ill. 1
Ill. 2
1. Tap the Create New Account button on the login dialog (see Ill. 1)
2. Enter a valid email address and the password on the login dialog. An activation link will
be sent to the specified email address (see Ill. 2)
3. Agree with the General Business Terms and Conditions and Data Protection Provisions
10
and tap the button
and the Data Protection Provisions can be reviewed by tapping the General Business
Terms and Conditions and Data Protection Provisions button.
. The complete text of the General Business Terms and Conditions
Ill. 3
Ill. 4
4. Enter the account details and tap the button. Entries indicated by an asterisk (*) are
mandatory entries. All other entries can also be filled in later (see Ill. 3)
5. Enter the your personal information and tap the
(see Ill. 4)
6. Once the account has been successfully registered, a message with an activation link
will be sent to the email address specified in the account name (make sure to check
the Spam folder). Otherwise, a failure notice will be displayed.
7. Confirm the activation link sent in the email message.
button to close the wizard
11
Loading...