Schumacher 00-99-000854, PP-2200, 94026931 User Manual
Model / Modelo: PP-2200
Portable Power
12V DC Power Source / Fuente de Poder para 12V DC
400 Watt Inverter / Inversor de Corriente de 400 Watt
OWNER’S MANUAL
MANUAL dEL USUARiO
READ ENTIRE MANUAL BEFORE
USING THIS PRODUCT
LEA EL MANUAL COMPLETO ANTES DE
UTILIZAR ESTE PRODUCTO
00-99-000854/0109
TABLE OF CONTENTS / ÍNDICE
SECTION / SECCIÓN PAGE / PÀGINA
IMPORTANT SAFETY INSTRUCTIONS 1
CONTROL PANEL 2
CHARGING THE INTERNAL BATTERY OF THE
PORTABLE POWER 2
OPERATING INSTRUCTIONS 3
STORAGE 5
SPECIFICATIONS 5
LIMITED WARRANTY 6
INSTRUCCIONES DE SEGURIDAD IMPORTANTES 8
PANEL DE CONTROL 9
PARA CARGAR LA BATERIA INTERNA DEL
PORTABLE POWER 9
INSTRUCCIONES DE OPERACIÓN 10
ALMACENAJE 12
ESPECIFICACIONES 13
GARANTÍA LIMITADA 13
IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.
CHARGE IMMEDIATELY AFTER PURCHASE.
IMPORTANT SAFETY INSTRUCTIONS1.
SAVE THESE INSTRUCTIONS – Charge the Portable Power internal 1.1
battery immediately after purchase, after every use and every 30 days.
WARNING:1.2 Pursuant to California Proposition 65, this product contains
chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
Contains a sealed, non-spillable lead-acid battery; must be disposed of 1.3
properly.
Keep the Portable Power well ventilated in order to properly disperse heat 1.4
generated while it is in use. Make sure there are several inches of clearance around the top and sides and do not block the slots of the Portable
Power.
Make sure the Portable Power is not close to any potential source of am-1.5
mable fumes, gases or clothing.
Keep the Portable Power dry.1.6
DO NOT allow the Portable Power to come into contact with rain or mois-1.7
ture.
DO NOT operate the Portable Power if you, the Portable Power, the 1.8
device being operated, or any other surfaces that may come in contact
with any power source are wet. Water and many other liquids can conduct
electricity, which may lead to serious injury.
Do not place the Portable Power on or near heating vents, radiators or 1.9
other sources of heat.
Do not modify the AC receptacle in any way.1.10
This device does not include an internal Ground Fault Circuit Interrupter 1.11
(GFCI). For GFCI protection, use a Coleman Cable 02822 GFCI outlet.
Do not permit the internal battery of the Portable Power to freeze. Never 1.12
charge a frozen battery.
Do not operate the Portable Power if it has received a sharp blow, been 1.13
dropped or otherwise damaged in any way; take it to a qualied service
person. (Call customer service at: 1-800-621-5485.)
Do not disassemble the Portable Power; take it to a qualied service 1.14
person when service or repair is required. Incorrect reassembly may
result in a risk of re or electric shock. (Call customer service at: 1-800-
621-5485.)
• 1 •
CONTROL PANEL2.
CHARGING THE INTERNAL BATTERY OF THE PORTABLE POWER3.
IMPORTANT: CHARGE IMMEDIATELY AFTER PURCHASE, AFTER
EACH USE AND EVERY 30 DAYS TO KEEP THE PORTABLE POWER
INTERNAL BATTERY FULLY CHARGED.
LED Indicators:3.1
TO CHECK THE INTERNAL BATTERY’S CHARGE STATUS, PRESS
THE BATTERY STATUS BUTTON ON THE FRONT OF THE PORTABLE
POWER
The LED lights will indicate the charge level as follows:1.
A red LED indicates a 50% or less charge, and you should immedi-•
ately recharge the Portable Power.
A yellow LED indicates a 50 to 70% charge. The Portable Power may •
be used but should be recharged as soon as possible.
A green LED indicates the internal battery is fully charged.•
The CHARGING (red) LED indicates the Portable Power is charging •
(connected to an AC power source). At full charge, the green LED will
light.
Charging the Internal Battery using the Plug-In Charger:3.2
After removing the Portable Power from the carton, charge it for a mini-1.
mum of 8 hours before using, even if the green LED glows.
NOTE: The ON/OFF switch should be in the OFF position to recharge the
internal battery.
To charge, plug the included wall charger into the socket on the front of 2.
the Portable Power.
Plug the wall charger into a 120V electrical wall outlet.3.
The CHARGING (red) LED will light indicating charging.4.
• 2 •
The green LED will light when the battery has reached full charge. This 5.
could take up to 72 hours due to the age and condition of the battery.
The charger will automatically go into maintain mode and maintain the
battery at full charge without damaging it.
Charge the Portable Power as soon as possible after use.6.
You may also charge the internal battery while driving, using the maleto-male charger cable (p/n 38-99-001564 – not included). Insert one end
of the accessory cable into the 12V DC power outlet and the other end
into the vehicle’s accessory outlet (lighter socket). Completely disconnect
the charger cable when the vehicle’s engine is not running. NOTE: The
Charging (red) LED and the green LED do not operate during this method
of charging.
OPERATING INSTRUCTIONS4.
Using The Inverter4.1
It is important to know the continuous wattage of the device you plan
to use with the inverter. The Portable Power must be used with devices
drawing 400 watts or less. If the wattage is not marked on the device, an
estimate can be made by multiplying the AC input current (Amps) by the
AC voltage (120V).
Devices like TVs, fans or electronic motors require additional power to
start (commonly known as the “starting or peak power”). The Portable
Power can supply a momentary surge in wattage; however, even devices
rated less than the maximum 400 watts can exceed the inverter’s surge
capability and cause an automatic overload shutdown.
Make sure the device you are using is compatible with the modied sine
wave inverter.
NOTE: In the event of a power overload, the inverter is designed to automatically shut down. This safety feature prevents damaging the inverter
while testing devices and equipment with the 400-watt limit.
Powering a 120V AC Device
To operate a 120V AC device:
Plug the 120V AC device into the AC power outlet, and push the inverter •
switch to ON. NOTE: The CHARGING (red) LED also functions as the
INVERTER ON light. When you push the inverter switch to the ON position, the CHARGING (red) LED will light.
Turn on the 120V AC device (if required).•
If a device will not operate properly when rst connected to the inverter, •
push the inverter rocker switch ON, OFF, and ON again in quick succession. If this procedure is not successful, it is likely that the Portable Power
does not have the required capacity to operate the device in question.
Charge the Portable Power as soon as possible after each use.•
• 3 •
Loading...