Operating Instructions
FRIDGE
GB
English, 1
SC12SLAAI
Contents
GB
Installation, 2-3
Positioning and connection
Description of the appliance, 4
Overall view
Accessories, 5
Start-up and use, 6
Starting the appliance
Setting the temperature
Using the refrigerator to its full potential
Maintenance and care, 7
Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Defrosting the appliance
Replacing the light bulb
Precautions and tips, 8
General safety
Disposal
Respecting and conserving the environment
Troubleshooting, 9
Assistance, 10
1
Installation
! Before placing your new appliance into operation please
GB
read these operating instructions carefully. They contain
important information for safe use, for installation and for
care of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free
room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Ensure the appliance is away from any sources of heat
(direct sunlight, electric stove, etc.).
Electrical connections
After the appliance has been transported, carefully place
it vertically and wait at least 3 hours before connecting it
to the electricity mains. Before inserting the plug into the
electrical socket ensure the following:
The appliance is earthed and the plug is compliant with
the law.
The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located
on the right side of the horizontal surface in the top
compartment, under the thermostat (e.g. 150 W).
The voltage is within the range of values indicated on
the data plate located on the right side of the horizontal
surface in the top compartment, under the thermostat
(e.g. 220-240V).
The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it (see Assistance). Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
Your appliance is supplied with a 13amp fused plug
that can be plugged into a 13amp socket for immediate
use. Before using the appliance please read the
instructions below.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
Replacing fuse covers:
When replacing a faulty fuse, a 13amp ASTA approved
fuse to BS 1362 should always be used and the fuse
cover re-fitted.
If the fuse cover is lost, the plug must not be used until
a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking or the
colour that is embossed in words on the base of the plug.
Changing the plug:
Removing the plug
If your appliance has a non-rewireable moulded plug
and you should wish to remove it to add a longer cable
or to re-route the mains cable through partitions, units
etc. please ensure that either:
- The plug is replaced by a fused 13amp rewireable plug bearing the BSI mark of
approval.
or
- The mains cable is wired directly into a
13amp cable outlet, controlled by a
switch (in compliance with BS 5733)
which is accessible without moving the
appliance.
Disposing of the plug
Cut off and dispose of the supplied plug if it does not fit
your socket. The cable should be cut as close as
possible to the moulded plug.
Remove the fuse.
WARNING:
To avoid a shock hazard do not insert the discarded
plug into a socket anywhere else.
! The manufacturer declines any liability should these
safety measures not be observed.
2
Fitting a new plug
IMPORTANT:
WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...
Green and Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- Connect Green and Yellow wire to terminal marked
'E' or
- Connect Brown wire to terminal marked 'L' or
coloured red or brown.
- Connect Blue wire to terminal marked 'N' or
coloured Black or Blue.
or coloured Green and Yellow.
GB
If a 13amp plug (BS 1363) is used it must be
fitted with a 13amp fuse. A 15amp plug must be
protected by a 15amp fuse, either in the plug or
adaptor or at the distribution board.
If you are in any doubt about the electrical
supply to your machine, consult a qualified
electrician before use.
CE Marking certifies that this appliance conforms to
the following EEC directives :
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/
EEC & 93/68/EEC
3
Description of the
appliance
Overall view
GB
The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not
directly represent the appliance purchased. For more complex features, consult the following pages.
CONTROL PANEL
Set TEMPERATURE
SUPER COOL
indicator light
indicator light
ADJUSTMENT
button
PURE WIND
CONTROL PANEL
SHELVES
PYREX storage
container
MULTI-USE
VEGETABLE bin
bin
FRUIT and
Removable lidded
shelf with EGG TRAY
and BUTTER DISH
HINGED shelf
*
Removable
multipurpose
SHELVES
*
*
*
Compartment for
A 2 LITRE BOTTLE
BOTTLE shelf
Varies by number and/or position.
Available only on certain models.
*
4
Accessories
SHELVES: with or without grill.
Due to the special guides the
shelves are removable and the
height is adjustable (see
diagram), allowing easy
storage of large containers and
food. Height can be adjusted
without complete removal of the
shelf.
MULTI-USE bin: to store food
(such as cold meats) for a long
time and also prevent odours
from lingering in the refrigerator.
It can be removed for use and it
may be shifted sideways to
optimise space (see diagram).
PYREX storage container: refer to the enclosed leaflet
for details on the various ways to use this container.
TEMPERATURE Indicator light: to identify the coldest
area in the refrigerator.
1. Check that OK appears clearly on the indicator light
(see diagram).
2. If the word OK does not appear it means that the
temperature is too high: adjust the REFRIGERATOR
OPERATION knob to a higher position (colder) and
wait approximately 10 hours until the temperature has
been stabilised.
3. Check the indicator light again: if necessary, readjust
it following the initial process. If large quantities of
food have been added or if the refrigerator door has
been opened frequently, it is normal for the indicator
not to show OK. Wait at least 10 hours before
adjusting the REFRIGERATOR OPERATION knob to a
higher setting.
GB
5
Start-up and use
Starting the appliance
GB
! Before starting the appliance, follow the installation
instructions (see Installation).
! Before connecting the appliance, clean the
compartments and accessories well with lukewarm water
and bicarbonate.
1. Plug the appliance in; make sure that the set
TEMPERATURE indicator light is illuminated and
showing the level +4°.
2. If necessary, use the relevant ADJUSTMENT button to set
the temperature to an intermediate value. After a few
hours you will be able to put food in the refrigerator.
Setting the temperature
The temperature inside the refrigerator compartment
automatically adjusts itself in accordance with the
selected temperature level as displayed by the
corresponding indicator light. The selected temperature
indicates the desired level of refrigeration.
+8° = warmest
+2° = coldest
We recommend, however, an intermediate position is
used (+4°/+6°).
The cooling section of the refrigerator is located inside
the back wall of the refrigerator compartment for
increased space and improved aesthetics. During
operation, the back wall will be covered in frost or water
droplets depending on whether the compressor is
operating or paused. Do not worry, the refrigerator is
functioning normally.
If the temperature adjustment system has been set to a
low value (colder), with large quantities of food and a
high room temperature, the appliance may operate
continuously, resulting in excessive frost formation and
excessive energy consumption: this may be avoided by
using the ADJUSTMENT button to set the temperature
to a higher value (warmer); automatic defrosting will
then take place.
Using the refrigerator to its full potential
Use the ADJUSTMENT button to activate the SUPER
COOL (rapid cooling) function, which will lower the
temperature quickly. This is useful, for example,
when you place a large number of new food items
inside the refrigerator and you need to counteract
the slight rise in its internal temperature. This
function is automatically deactivated after the
required amount of time has passed.
Place only cold or lukewarm foods in the
compartment, not hot foods (see Precautions and
tips).
Remember that cooked foods do not last longer than
raw foods.
Do not store liquids in open containers. They will
increase humidity in the refrigerator and cause
condensation to form.
Food hygiene
PURE WIND SYSTEM
It is recognizable due to the presence of the
mechanism on the top part of the refrigerator
compartment (see diagram).
B
A
Pure Wind System maximises air circulation, improving
the efficiency of the evaporator and helping to achieve
the optimal temperature inside the refrigerator as quickly
as possible each time it has been opened. The blown air
(A) is cooled when it comes into contact with the cold
wall, whereas the hotter air (B) is sucked up (see
diagram).
6
B
A
B
1. Once you have bought your food, remove all
external packaging made of paper/cardboard or
other wrappers, which could introduce bacteria or
dirt inside your refrigerator.
2. Protect the food, (especially easily perishable items
and those that have a strong smell), in order to avoid
contact between them, thereby removing both the
possibility of germ/bacteria contamination as well as
the diffusion of strong odours inside the fridge.
3. Store all food in such a way as to ensure air can
circulate freely between different items.
4. Keep the inside of your fridge clean, taking care not
to use oxidiser or abrasive products.
5. Remove all food past its expiry date from the
refrigerator.
6. For the correct preservation of food, all easily
perishable items (soft cheeses, raw fish, meat, etc.)
should be stored in the coldest zone of the fridge
compartment, i.e. just above the salad crisper where
the temperature indicator is situated.
Maintenance and care
Switching the appliance off
During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply:
It is not sufficient to set the temperature adjustment
knobs on
contact.
(appliance off) to eliminate all electrical
Cleaning the appliance
The external and internal parts, as well as the rubber
seals may be cleaned using a sponge that has been
soaked in lukewarm water and bicarbonate of soda
or neutral soap. Do not use solvents, abrasive
products, bleach or ammonia.
The removable accessories may be soaked in warm
water and soap or dishwashing liquid. Rinse and dry
them carefully.
Avoiding mould and unpleasant odours
Defrosting the appliance
GB
! Follow the instructions below.
Do not use objects with sharp or pointed edges to
defrost the appliance as these may damage the
refrigeration circuit beyond repair.
The refrigerator has an
automatic defrosting
function: water is ducted
to the back of the
appliance by a special
discharge outlet (see
diagram) where the heat
produced by the
compressor causes it to
evaporate. It is necessary
to clean the discharge
hole regularly so that the
water can flow out easily.
Replacing the light bulb
The appliance is manufactured with hygienic
materials which are odour free. In order to maintain
an odour free refrigerator and to prevent the
formation of stains, food must always be covered or
sealed properly.
If you want to switch the appliance off for an
extended period of time, clean the inside and leave
the doors open.
To replace the light bulb in the refrigerator
compartment, pull out the plug from the electrical
socket. Follow the instructions below.
Access the light bulb by
removing the cover as
indicated in the diagram.
Replace it with a similar
light bulb within the
power range indicated
on the cover (15W or
25W).
7
Precautions and tips
! The appliance was designed and manufactured in
GB
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
This appliance complies with the following
Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC of 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE.
General safety
The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
The appliance must be used to store and freeze food
products by adults only and according to the
instructions in this manual.
The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
Do not touch the appliance with bare feet or with wet or
moist hands and feet.
Do not touch the internal cooling elements: this could
cause skin abrasions or frost/freezer burns.
When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
Before cleaning and maintenance, always switch off the
appliance and disconnect it from the electrical supply. It
is not sufficient to set the temperature adjustment knobs
(appliance off) to eliminate all electrical contact.
on
In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
Do not use devices or tools other than the special
scraper provided inside the compartments.
Do not put ice cubes taken directly from the freezer into
your mouth.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
lack of experience and knowledge unless they have
been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
Keep packaging material out of the reach of children! It
can become a choking or suffocation hazard.
Disposal
Observe local environmental standards when
disposing packaging material for recycling
purposes.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment. The crossed out
wheeled bin symbol on the product reminds you of
your obligation, that when you dispose of the
appliance it must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Respecting and conserving the
environment
Install the appliance in a fresh and well-ventilated
room. Ensure that it is protected from direct sunlight
and do not place it near heat sources.
Try to avoid keeping the door open for long periods
or opening the door too frequently in order to
conserve energy.
Do not fill the appliance with too much food:
cold air must circulate freely for food to be preserved
properly. If circulation is impeded, the compressor
will work continuously.
Do not place hot food directly into the refrigerator.
The internal temperature will increase and force the
compressor to work harder and will consume more
energy.
Defrost the appliance if ice forms (see Maintenance).
A thick layer of ice makes cold transference to food
products more difficult and results in increased
energy consumption.
Regularly check the door seals and wipe clean to
ensure they are free of debris and to prevent cold air
from escaping (see Maintenance).
8
Troubleshooting
Assistance
If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.
Malfunctions:
The internal light does not
illuminate.
The refrigerator do not cool well.
The food inside the refrigerator is
beginning to freeze.
The PURE WIND fan does not rotate.
The motor runs continuously.
The appliance makes a lot of noise.
Possible causes / Solutions:
The plug has not been inserted into the electrical socket, or not far
enough to make contact, or there is no power in the house.
The door do not close properly or the seals are damaged.
The door are opened too frequently.
The TEMPERATURE ADJUSTMENT knob is not in the correct position
The refrigerator or the freezer have been over-filled.
The TEMPERATURE ADJUSTMENT knob is not in the correct position.
The food is in contact with the back inside wall of the refrigerator.
The PURE WIND system is only activated automatically when it
becomes necessary to restore perfect operational conditions inside the
refrigerator compartment.
The door is not closed properly or is continuously opened.
The outside ambient temperature is very high.
The appliance has not been installed on a level surface (see Installation).
The appliance has been installed between cabinets that vibrate and
make noise.
The internal refrigerant makes a slight noise even when the compressor
is off. This is not a defect, it is normal.
GB
The alarm sounds and the lamp
flashes.
The alarm sounds and the set
temperature indicator lights flash
(all of them excluding the Super Cool
indicator light which is turned off).
The back wall of the refrigerator unit
is covered in frost or droplets of
water.
There is water at the bottom of the
refrigerator.
The refrigerator door has been open for more than 2 minutes. The
buzzer will stop sounding when the door is shut.
The appliance signals that it has heated excessively. We recommend
checking the state of the foodstuffs: they may need to be removed. In
this situation, the product continues functioning as in the normal
functioning mode. The buzzer can be stopped by simply opening and
closing the door. To stop the indicator lights from flashing, it is
necessary to turn off the appliance using the adjustment button (OFF),
then use the same button to switch on the appliance and restore
normal functioning at the desired temperature.
This shows the appliance is operating normally.
The water discharge hole is blocked (see Maintenance).
9
Assistance
GB
Before calling for Assistance:
Check if the malfunction can be solved on your own (see Troubleshooting).
If after all the checks, the appliance still does not operate or the problem persists, call the nearest Service Centre
model serial number
Communicating:
type of malfunction
appliance model (Mod.)
serial number (S/N)
This information can be found on the data plate
located on the right side of the horizontal surface in the
top compartment (under the thermostat).
Never call on unauthorized technicians and always refuse spare parts which are not originals.
10
COMMITMENT TO AFTER SALES SUPPORT
THANK YOU FOR INVESTING IN SCHOLTÈS
Scholtès products are designed to perform consistently and reliably throughout their life.
To give you further reassurance Scholtès ensures your appliance benefits from a five year guarantee.
This promise means, that if within five years from the date of purchase of your appliance it is proven to
be defective Scholtès will, at its discretion, repair or replace the appliance at no additional cost.
CONTACT
There is a dedicated team of advisors to provide free advice and assistance with any problem you
experience with a Scholtès appliance. Where necessary, Scholtès will arrange for an engineer from its
specialist field support team to resolve the issue with the least disruption.
TELEPHONE FREE ON 0800 158 55 00
To help manage potential problems quickly and effectively Scholtès recommends registering all
appliances. To register appliances, telephone free on 0800 158 55 00 or visit www.scholtes.co.uk.
GB
This garantee is subject to the following conditions:-
The appliance has been installed and operated correctly and in accordance with the operating and maintenance instructions.
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered serviced, maintained, dismantled, or otherwise interfered with by any person not
authorized by Scholtès.
Any repair work be undertaken by Scholtès or an appointed agent.
Any parts removed during repair work or any appliance that is replaced becomes the property of Scholtès.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
Damage resulting from transportation improper use, neglect or interference or as a result of improper installation.
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables, batteries, light bulbs,
fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THE GARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON DOMESTIC PREMISES.
11
GB
195085236.00
03/2010 - Xerox Fabriano
12
Loading...