SCHOLTES TIS 632 CDL,TIS 62 CL,TIS 632 CDL Operating Instructions Manual
Operating Instructions
Contents
Installation, 26-27
Positioning
Electrical connection
Description of the appliance, 28
Control panel
Start-up and use, 29-33
Switching on the hob
Switching on the cooking zones
Medium function
Booster function
Switching off the cooking zones
Programming the cooking duration
Timer
Control panel lock
Switching off the hob
“Demo” mode
EXTENSO TECHNOLOGY mode
Practical advice on using the appliance
Safety devices
Practical cooking advice
Precautions and tips, 34
General safety
Disposal
Care and maintenance, 35
Switching the appliance off
Cleaning the appliance
Disassembling the hob
Technical description of the models, 36
HOB
Italiano, 1
GB
Espanol, 49
ES
Deutsch, 37
DE
Français, 13 English,25
IT FR
TIS 632 CDL
TIS 62 CL
26
GB
Installation
! Before operating your new appliance please read this
instruction booklet carefully. It contains important
information concerning the safe operation, installation and
maintenance of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to any new owners of the
appliance.
Positioning
! Keep all packaging material out of the reach of children.
It may present a choking or suffocation hazard (
see
Precautions and tips
).
! The appliance must be installed by a qualified
professional in accordance with the instructions provided.
Incorrect installation may cause harm to people and
animals or may damage property.
Built-in appliance
Use a suitable cabinet to ensure that the appliance
functions properly.
• The supporting surface must be heat-resistant up to a
temperature of approximately 100°C.
• If the appliance is to be installed above an oven, the
oven must be equipped with a forced ventilation
cooling system.
• Avoid installing the hob above a dishwasher: if this
cannot be avoided, place a waterproof separation
device between the two appliances.
• Depending on the hob you want to install, the cabinet
must have the following dimensions (
see figure
):
560 +/- 1
490 +/- 1
48
590
520
6
9
0
520
560 +/- 1
490 +/- 1
48
Ventilation
To allow adequate ventilation and to avoid overheating of the
surrounding surfaces the hob should be positioned as follows:
• At a minimum distance of 40 mm from the back panel
or any other vertical surfaces.
• So that a minimum distance of 20 mm is maintained
between the installation cavity and the cabinet
underneath.
• Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 600 mm from
the edge of the hob.
FRONT SIDE
OF HOB
SUPPORTING
SURFACE
30
40
UNDERSIDE
OF HOB
5 mm
min. 20 mm
min. 20 mm
min. 40 mm
COMPARTMENT
5 mm
min. 40 mm
FAN-ASSISTED
OVEN
27
GB
Fixing
The appliance must be installed on a perfectly level
supporting surface.
Any deformities caused by improper fixing could affect
the features and operation of the hob.
The thickness of the supporting surface
should be taken
into account when choosing
the length of the screws for the
fixing hooks:
• 30 mm thick: 23 mm screws
• 40 mm thick: 13 mm screws
Fix the hob as follows:
1. Use short flat-bottomed screws to fix the 4 alignment
springs in the holes provided at the central point of each
side of the hob.
2. Place the hob in the cavity, make sure it is in a central
position and push down on the whole perimeter until the
hob is stuck to the supporting surface.
3. For hobs with raised sides: After inserting the hob into
its cavity, insert the 4 fixing hooks (each has its own pin)
into the lower edges of the hob, using the long pointed
screws to fix them in place, until the glass is stuck to the
supporting surface.
! The screws for the alignment springs must remain
accessible.
! In order to adhere to safety standards, the appliance
must not come into contact with electrical parts once it
has been installed.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a tool.
Electrical connection
! The electrical connection for the hob and for any built-in
oven must be carried out separately, both for safety
purposes and to make extracting the oven easier.
Single-phase connection
The hob is equipped with a pre-connected electricity
supply cable, which is designed for single-phase
connection. Connect the wires in accordance with the
instructions given in the following table and diagrams:
Voltage and
mains frequency
Electrical cable Wire connection
220-240V 1+N ~
50 Hz
: yellow/green
N
: the two blue wires together
L
: brown and black together
Other types of connection
If the mains supply corresponds with one of the following:
Voltage and mains frequency
• 400V - 2+N ~ 50 Hz
• 220-240V 3 ~ 50 Hz
• 400V 3 - N ~ 50 Hz
• 400V - 2+2N ~ 50 Hz
Separate the wires and connect them in accordance with
the instructions given in the following table and diagrams:
Voltage and
mains frequency
Electrical cable Wire connection
400V - 2+N ~
50 Hz
220-240V 3 ~
50 Hz
400V 3-N ~
50 Hz
: yellow/green;
N: the two blue wires
together
L1: black
L2: brown
400V - 2+2N ~
50 Hz
: yellow/green;
N1: blue
N2: blue
L1: black
L2: brown
Connecting the electricity supply cable to the mains
If the appliance is being connected directly to the
electricity mains an omnipolar switch must be installed
with a minimum opening of 3 mm between contacts.
! The installer must ensure that the correct electrical
connection has been made and that it is fully compliant
with safety regulations.
Before connecting the appliance to the power supply,
make sure that:
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located
on the appliance itself.
• The voltage falls within the range of values indicated on
the data plate.
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the plug,
ask an authorised technician to replace it. Do not use
extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only.
! The manufacturer declines any liability should these
safety measures not be observed.
! Do not remove or replace the power supply cable for any
reason. Its removal or replacement will void the warranty
and the CE marking. INDESIT does not assume liability
for accidents or damage arising from replacement/
removal of the original power supply cable. Replacement
can only be accepted when carried out by personnel
authorised by INDESIT and using an original spare part.
28
GB
Description of the
appliance
Control panel
The control panel described in this manual is only a representative example: it may not exactly match the panel
on your appliance.
*
Only available in certain models.
ON/OFF indicator light
CONTROLS LOCKED
indicator light
CONTROL PANEL LOCK
button
INCREASE TIME*
button
COOKING ZONE PROGRAMMED*
indicator light
PROGRAMME TIMER*
display
PROGRAMME TIMER
button
DECREASE TIME*
button
POWER and
RESIDUAL HEAT
indicators
ON/OFF button
COOKING ZONE
indicator
TIMER*
indicator light
BOOSTER*
button
BOOSTER*
indicator light
SLIDER ZONE
X
button
button
button
EXTENSO TECHNOLOGY
button
EXTENSO TECHNOLOGY
indicator light
•
"SLIDER" ZONE -"SLIDER" ZONE -
"SLIDER" ZONE -"SLIDER" ZONE -
"SLIDER" ZONE - switches the hotplate on/off or
adjusts its power level (see Start-up and use).
• COOKING ZONE indicator represents the
corresponding cooking zone.
• POWER indicator provides a visual display for the
current heat level.
• ON/OFF button switches the appliance on and off.
• ON/OFF indicator light shows whether the
appliance is on or off.
• PROGRAMME TIMER* button controls the
cooking programme times (
see Start-up and use
).
• PROGRAMME TIMER* display shows which
programme has been selected (
see Start-up and
use
).
• COOKING ZONE PROGRAMMED* indicator lights
show which cooking zones are being used during
a cooking programme (
see Start-up and use
).
• CONTROL PANEL LOCK button prevents
accidental changes to the hob settings (
see Start-
up and use
).
• CONTROL PANEL LOCK indicator light shows
the control panel has been locked (
see Start-up
and use
).
• BOOSTER* button activates the booster function -
3000 W - of the cooking zone
(see Start-up and
use).
• BOOSTER* indicator light shows that the booster
function has been activated.
• TIMER* indicator light shows that the timer has
been activated
• MAX BUTTON - switches the cooking zone on at
its maximum power level 16 (see Start-up and
use).
• MED BUTTON - switches the cooking zone on at
its medium power level 8 (see Start-up and use).
• MIN BUTTON - switches the cooking zone on at
its minimum power level 1 (see Start-up and use).
• INCREASE TIME* button increases the cooking
duration while the timer is running or while a set
programme is underway
(see Start-up and use).
• DECREASE TIME* button decreases the cooking
duration while the timer is running or while a set
programme is underway
(see Start-up and use).
• EXTENSO TECHNOLOGY button - activates the
EXTENSO TECHNOLOGY mode
• EXTENSO TECHNOLOGY indicator light shows
that the EXTENSO TECHNOLOGY function has
been activated
! This product complies with the requirements of the
latest European Directive on the limitation of power
consumption of the standby mode.
If no operations are carried out for a period of 2
minutes, after the residual heat indicator lights turn
off and the fan stops (if present), the appliance
automatically switches to the “off mode”.
The appliance resumes the operating mode once the
ON/OFF button is pressed.
Loading...